New Fe-Ni Based Metal-Metalloid Glassy Alloys Prepared by Mechanical Alloying and Rapid Solidification

1996 ◽  
Vol 455 ◽  
Author(s):  
J. J. Suñol ◽  
M. T. Clavaguera-Mora ◽  
N. Clavaguera ◽  
T. Pradell
Keyword(s):  
Mechanical Alloying ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
Magnetic Interaction ◽  
Processing Route ◽  
Mechanically Alloyed ◽  
Scanning Calorimetry ◽  
Glassy Alloys ◽  
Rapidly Solidified ◽  
Thermal Stability Of

ABSTRACTMechanical alloying and rapid solidification are two important routes to obtain glassy alloys. New Fe-Ni based metal-metalloid (P-Si) alloys prepared by these two different processing routes were studied by differential scanning calorimetry and transmission Mössbauer spectroscopy. Mechanical alloyed samples were prepared with elemental precursors, and different nominal compositions. Rapidly solidified alloys were obtained by melt-spinning. The structural analyses show that, independent of the composition, the materials obtained by mechanical alloying are not completely disordered whereas fully amorphous alloys were obtained by rapid solidification. Consequently, the thermal stability of mechanically alloyed samples is lower than that of the analogous material prepared by rapid solidification. The P/Si ratio controls the magnetic interaction of the glassy ribbons obtained by rapid solidification. The experimental results are discussed in terms of the degree of amorphization and crystallization versus processing route and P/Si ratio content.

scholarly journals The Development of Rapidly Solidified Magnesium – Copper Ribbons

2016 ◽  
Vol 61 (2) ◽  
pp. 1083-1088
Author(s):  
M. Pastuszak ◽  
G. Cieślak ◽  
A. Dobkowska ◽  
J. Mizera ◽  
K.J. Kurzydłowski
Keyword(s):  
Corrosion Resistance ◽  
Cooling Rate ◽  
Melt Spinning ◽  
Diffraction Method ◽  
Electrode System ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Copper Addition ◽  
Rapidly Solidified ◽  
Thermal Stability Of

Abstract The aim of the present work was to plan and carry out an experiment consisting of amorphization of industrial magnesium alloy WE 43 (Mg - 4 Y - 3 RE - 0.5 Zr) modified by the copper addition. Investigated alloy modified with 20% of copper was rapidly quenched with the use of melt spinning technique. The effects of cooling rate on the structure and properties of the obtained material were extensively analyzed. The structure and phase analysis of samples were examined using X-ray diffraction method (XRD) while the thermal stability of the samples was determined by differential scanning calorimetry (DSC). Microstructure observations were also conducted. The microhardness tests (HV0.02) and corrosion resistance tests were carried out to investigate the properties of the material. Corrosion resistance measurements were held using a typical three-electrode system. As the result of the research, the effect of cooling rate on microstructure and properties of investigated alloy was determined.

Copper-Base Alloys Processed by Rapid Solidification and Ion Implantation

1985 ◽  
Vol 58 ◽  
Author(s):  
J.V. Wood ◽  
C.J. Elvidge ◽  
E. Johnson ◽  
A. Johansen ◽  
L. Sarholt-Kristensen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Martensitic Transformation ◽  
Ion Implantation ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
Scanning Calorimetry ◽  
Copper Base ◽  
Similarities And Differences ◽  
Rapidly Solidified

ABSTRACTAlloys of Cu-Sn and Cu-B have been processed by both melt spinning and ion implantation. In some instances (eg Cu-Sn alloys) rapidly solidified ribbons have been subjected to further implantation. This paper describes the similarities and differences in structure of materials subjected to a dynamic and contained process. For example in Cu-B alloys (up to 2wt% Boron) extended solubility is found in implanted alloys which is not present to the same degree in rapidly solidified alloys of the same composition. Likewise the range and nature of the reversible martensitic transformation is different in both cases as examined by electron microscopy and differential scanning calorimetry.

Influence of Sn Addition on the Amorphization and Thermal Stability of CuTiZrNi Powders Processed by Mechanical Alloying

2010 ◽  
Vol 636-637 ◽  
pp. 917-921 ◽  
Author(s):  
Dariusz Oleszak ◽  
Tadeusz Kulik
Keyword(s):  
Thermal Stability ◽  
Mechanical Alloying ◽  
Crystallization Behaviour ◽  
Chemical Compositions ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
Scanning Calorimetry ◽  
Activation Energy Of Crystallization ◽  
Preparation Techniques ◽  
Thermal Stability Of

The influence of Sn addition on the amorphization of CuTiZrNi alloys processed by mechanical alloying of a mixture of pure elemental powder was studied. The thermal stability and crystallization behaviour of the amorphous mechanically alloyed powders was determined and compared with rapidly quenched ribbons with the same nominal chemical compositions. X-ray diffraction and differential scanning calorimetry were employed as the experimental techniques for samples characterization. Both applied samples preparation techniques resulted in the formation of fully amorphous Cu47Ti34Zr11Ni8 and Cu37Sn10Ti34Zr11Ni8 alloys. However, significant differences in thermal stability and crystallization behaviour have been found, depending not only on the alloy composition, but on the fabrication method as well. The observed influence of Sn addition was more evident for the ribbons, resulting in the change of the number of crystallization effects, their temperatures and activation energy of crystallization. For mechanically alloyed powders these changes were not so dramatic.

Synthesis and Thermoelectric Properties of Undoped Half-Heusler Zr-Co-Sb Alloy Processed by Mechanically Alloying and Hot Pressing

2011 ◽  
Vol 695 ◽  
pp. 69-72
Author(s):  
Il Ho Kim ◽  
Joon Chul Kwon ◽  
Young Geun Lee ◽  
Sung Lim Ryu ◽  
Man Soon Yoon ◽  
...  
Keyword(s):  
Mechanical Alloying ◽  
Thermoelectric Properties ◽  
Thermoelectric Materials ◽  
Hot Pressing ◽  
Heusler Alloys ◽  
Processing Route ◽  
Mechanically Alloyed ◽  
Fundamental Study ◽  
Vacuum Hot Pressing ◽  
Fine Grain

Half-Heusler alloys are one of the potential thermoelectric materials for medium to high temperature range application. As a part of fundamental study to establish processing route and to observe thermoelectric properties in undoped state, ZrCoSb was selected, processed and evaluated. In an attempt to produce a half-Heusler thermoelectric materials having ultra fine grain structures, ZrCoSb was synthesized by mechanical alloying of stoichiometric elemental powder compositions, and consolidated by vacuum hot pressing. Phase transformations during mechanical alloying and hot consolidation were investigated using XRD, SEM and EDS. Single-phase, half-Heusler was successfully produced by vacuum hot pressing using as-milled powders without subsequent annealing. Thermoelectric properties as functions of temperature were evaluated in terms of Seebeek coefficient, electrical conductivity, thermal conductivity and the figure of merit for the hot pressed specimens. Mechanically alloyed half-Heusler phase, ZrCoSb, appeared to have a great potential as a thermoelectric materials in this study.

Thermal Stability of Amorphous Ti- Cu- Ni- Sn Prepared by Mechanical Alloying

2007 ◽  
Vol 534-536 ◽  
pp. 233-236 ◽  
Author(s):  
N.T.H. Oanh ◽  
Pyuck Pa Choi ◽  
Ji Soon Kim ◽  
Dae Hwan Kwon ◽  
Young Soon Kwon
Keyword(s):  
Thermal Stability ◽  
Differential Scanning Calorimetry ◽  
Mechanical Alloying ◽  
Amorphous Alloys ◽  
High Energy ◽  
Scanning Calorimetry ◽  
Thermal Stability Of

Ti-Cu-Ni-Sn quaternary amorphous alloys of Ti50Cu32Ni15Sn3, Ti50Cu25Ni20Sn5, and Ti50Cu23Ni20Sn7 composition were prepared by mechanical alloying in a planetary high-energy ballmill (AGO-2). The amorphization of all three alloys was found to set in after milling at 300rpm speed for 2h. A complete amorphization was observed for Ti50Cu32Ni15Sn3 and Ti50Cu25Ni20Sn5 after 30h and 20h of milling, respectively. Differential scanning calorimetry analyses revealed that the thermal stability increased in the order of Ti50Cu32Ni15Sn3, Ti50Cu25Ni20Sn5, and Ti50Cu23Ni20Sn7.

Rapidly Solidified Binary Tial Alloys

1986 ◽  
Vol 81 ◽  
Author(s):  
S. C. Huang ◽  
E. L. Hall ◽  
M. F. X. Gigliotti
Keyword(s):  
Electron Diffraction ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
Grain Structure ◽  
Bending Tests ◽  
Tial Alloys ◽  
Compositional Effect ◽  
X Ray ◽  
Antiphase Domains ◽  
Rapidly Solidified

AbstractMelt spinning has been carried out on binary TiAl alloys at three Ti/Al ratios. Antiphase domains were observed in one ribbon specimen, but no significant disordering was induced by the rapid solidification as indicated by X-ray and electron diffraction analyses. Bending tests of both the ribbons and the consolidated counterparts showed a decrease in ductility with increasing Al concentration. This compositional effect can be correlated with the TiAl tetragonality (the c/a ratio) as well as the grain structure.

scholarly journals MICROSTRUCTURE AND THERMAL STABILITY OF Al-Fe-X ALLOYS

2018 ◽  
Vol 24 (3) ◽  
pp. 223 ◽  
Author(s):  
Andrea Školáková ◽  
Petra Hanusová ◽  
Filip Průša ◽  
Pavel Salvetr ◽  
Pavel Novák ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Melt Spinning ◽  
Hot Extrusion ◽  
Dispersed Particles ◽  
Cast Alloys ◽  
Rapidly Solidified ◽  
Thermal Stability Of ◽  
Melt Spinning Technique ◽  
Extrusion Method

<p>In this work, Al-11Fe, Al-7Fe-4Ni and Al-7Fe-4Cr (in wt. %) alloys were prepared by combination of casting and hot extrusion. Microstructures of as-cast alloys were composed of aluminium matrix with large and coarse intermetallics such as Al<sub>13</sub>Fe<sub>4</sub>, Al<sub>13</sub>Cr<sub>2</sub> and Al<sub>5</sub>Cr. Subsequently, as-cast alloys were rapidly solidified by melt-spinning technique which led to the supersaturation of solid solution alloying elements. These rapidly solidified ribbons were milled and compacted by hot-extrusion method. Hot-extrusion caused that microstructures of all alloys were fine with uniform dispersed particles. Moreover, long-term thermal stability was tested at temperature 300 °C for as-cast and hot-extruded alloys and chromium was found to be the most suitable element for alloying to improve thermal stability.    </p>

Solid State Amorphization of Ti60Si40 Alloy via Mechanical Alloying

2021 ◽  
Vol 876 ◽  
pp. 7-12
Author(s):  
Petr Urban ◽  
Fátima Ternero Fernández ◽  
Rosa M. Aranda Louvier ◽  
Raquel Astacio López ◽  
Jesus Cintas Físico
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Mechanical Alloying ◽  
Amorphous Phase ◽  
Milling Time ◽  
X Ray Diffraction ◽  
Mechanically Alloyed ◽  
Scanning Calorimetry ◽  
Transmission Electron ◽  
Heating Up

The effect of milling time on the microstructure evolution and formation of amorphous phase of Ti60Si40 alloy produced by mechanical alloying (MA) has been investigated. Laser diffraction, Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Transmission Electron Microscopy (TEM) and Differential Scanning Calorimetry (DSC) were employed to characterize the particle size, morphology and structure of mechanically alloyed Ti60Si40. When the milling time is increased to 20 h, the particle size decreases from 23.7 to 4.7 μm, the shape of the particles changes to spherical and the crystalline structure is transformed into an amorphous phase. The amorphous Ti60Si40 alloy is stable when heating up to 750oC. Above this temperature, the cold crystallization of the intermetallic compounds Ti5Si3 and/or Ti5Si4 begins.

Thermal Stability of Amorphous Al-Fe-Y Prepared by Mechanical Alloying

2014 ◽  
Vol 804 ◽  
pp. 271-274 ◽  
Author(s):  
Nguyen Hoang Viet ◽  
Nguyen Thi Hoang Oanh ◽  
Pham Ngoc Dieu Quynh ◽  
Tran Quoc Lap ◽  
Ji Soon Kim
Keyword(s):  
Thermal Stability ◽  
Mechanical Alloying ◽  
Amorphous Alloys ◽  
Ball Mill ◽  
The Other ◽  
Scanning Calorimetry ◽  
Powder Alloys ◽  
Stage Crystallization ◽  
Dsc Analyses ◽  
Thermal Stability Of

Al-Fe-Y amorphous alloys of Al84Fe16, Al82Fe18 and Al82Fe16Y2 composition were prepared by mechanical alloying in a planetary ball mill P100. A nearly complete amorphization could be achieved for the Al84Fe16, Al82Fe18 and Al82Fe16Y2 powder alloys after 100h of milling at a rotational speed of 350 rpm in hexane medium. Differential scanning calorimetry (DSC) analyses revealed three-stage crystallization processes for Al82Fe18 and Al82Fe16Y2 alloys and four-stage crystallization processes for Al84Fe16 alloy, respectively. Taking into account the DSC data, the thermal stability increased in the order of Al84Fe16, Al82Fe18, and Al82Fe16Y2 composition. The Al82Fe16Y2 alloy exhibited a relatively better thermal stability than the other two alloys.

Substructure Development in Rapidly Solidified B2-Type TiCo Ribbons

2005 ◽  
Vol 475-479 ◽  
pp. 849-852 ◽  
Author(s):  
Kyosuke Yoshimi ◽  
Minseok Sung ◽  
Sadahiro Tsurekawa ◽  
Akira Yamauchi ◽  
Ryusuke Nakamura ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Dislocation Density ◽  
Rapid Solidification ◽  
Melt Spinning ◽  
Grain Structure ◽  
Second Phase ◽  
Rapidly Solidified ◽  
Equiaxed Grain

Substructure development through aging and annealing treatments was studied for rapidly solidified TiCo ribbons using TEM. In as-spun ribbons, equiaxed grain structure was developed and its crystal structure was B2-ordered immediately after melt-spinning, while a small amount of fine precipitates existed as second phase. Some grains were dislocation-free but others contained a certain amount of curved or helical dislocations and loops. The dislocation density in the ribbons annealed at 700 °C for 24 h was obviously higher than those in the as-spun ribbons and the ribbons aged at 200 °C for 100 h. The increase of the dislocation density in the annealed ribbons would result from the absorption of excess vacancies. Therefore, the obtained results indicated that a large amount of supersaturated thermal vacancies were retained in TiCo as-spun ribbons by the rapid solidification.

Sign in / Sign up

Export Citation Format

Share Document