Metalorganic chemical vapor deposition of aluminum oxide on silicon nitride

2002 ◽  
Vol 751 ◽  
Author(s):  
Anindya Dasgupta ◽  
Abhijit Roy Chowdhuri ◽  
Christos G. Takoudis
Keyword(s):  
Thin Films ◽  
Silicon Nitride ◽  
Aluminum Oxide ◽  
Silicon Oxide ◽  
Chemical Vapor ◽  
Aluminum Silicate ◽  
Excess Oxygen ◽  
Silicon Substrates ◽  
Interfacial Layers ◽  
Film Substrate

ABSTRACTThin films of aluminum oxide were deposited on silicon nitride thin films using trimethylaluminum and oxygen at 0.5 Torr and 300 °C. Fourier transform infrared (FTIR) and x-ray photoelectron spectroscopic (XPS) analyses of these films showed no aluminum silicate phase at the film-substrate interface. The O/Al ratio in the deposited film was found to be higher than that in stoichiometric Al2O3 indicating the presence of excess oxygen. FTIR spectroscopy and XPS of the annealed samples did not show any formation of silicon oxide, oxynitride or silicate at the aluminum oxide/silicon nitride interface. In contrast to aluminum oxide on clean silicon substrates, using ultrathin silicon nitride as a barrier layer could prevent excess oxygen migration towards the Si substrate and formation of any interfacial layers.

Microbridge Testing of Thin Films Under Small Deformation

1999 ◽  
Vol 594 ◽  
Author(s):  
T. Y. Zhang ◽  
Y. J. Su ◽  
C. F. Qian ◽  
M. H. Zhao ◽  
L. Q. Chen
Keyword(s):  
Thin Films ◽  
Residual Stress ◽  
Silicon Nitride ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Chemical Vapor ◽  
Small Deformation ◽  
Nitride Film ◽  
Silicon Nitride Film ◽  
Pressure Chemical

AbstractThe present work proposes a novel microbridge testing method to simultaneously evaluate the Young's modulus, residual stress of thin films under small deformation. Theoretic analysis and finite element calculation are conducted on microbridge deformation to provide a closed formula of deflection versus load, considering both substrate deformation and residual stress in the film. Silicon nitride films fabricated by low pressure chemical vapor deposition on silicon substrates are tested to demonstrate the proposed method. The results show that the Young's modulus and residual stress for the annealed silicon nitride film are respectively 202 GPa and 334.9 MPa.

Residual Stress in Sputtered Silicon Oxycarbide Thin Films

2011 ◽  
Vol 1299 ◽  
Author(s):  
Ping Du ◽  
I-Kuan Lin ◽  
Yunfei Yan ◽  
Xin Zhang
Keyword(s):  
Thin Films ◽  
Residual Stress ◽  
Elevated Temperatures ◽  
Silicon Oxide ◽  
Composite Films ◽  
Deposition Process ◽  
Silicon Oxycarbide ◽  
X Ray ◽  
Curvature Measurement ◽  
Film Substrate

ABSTRACTSilicon carbide (SiC) has received increasing attention on the integration of microelectro-mechanical system (MEMS) due to its excellent mechanical and chemical stability at elevated temperatures. However, the deposition process of SiC thin films tends to induce relative large residual stress. In this work, the relative low stress material silicon oxide was added into SiC by RF magnetron co-sputtering to form silicon oxycarbide (SiOC) composite films. The composition of the films was characterized by Energy dispersive X-ray (EDX) analysis. The Young’s modulus and hardness of the films were measured by nanoindentation technique. The influence of oxygen/carbon ratio and rapid thermal annealing (RTA) temperature on the residual stress of the composite films was investigated by film-substrate curvature measurement using the Stoney’s equation. By choosing the appropriate composition and post processing, a film with relative low residual stress could be obtained.

Measurement of The Activation Energy in Phosphorous Doped Polycrystalline Diamond Thin Films Grown on Silicon Substrates by Hot Filament Chemical Vapor Deposition

1996 ◽  
Vol 423 ◽  
Author(s):  
S. Mirzakuchaki ◽  
H. Golestanian ◽  
E. J. Charlson ◽  
T. Stacy
Keyword(s):  
Thin Films ◽  
Activation Energy ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Polycrystalline Diamond ◽  
Silicon Substrates ◽  
Boron Doped Diamond ◽  
Diamond Thin Films ◽  
Hot Filament

AbstractAlthough many researchers have studied boron-doped diamond thin films in the past several years, there have been few reports on the effects of doping CVD-grown diamond films with phosphorous. For this work, polycrystalline diamond thin films were grown by hot filament chemical vapor deposition (HFCVD) on p-type silicon substrates. Phosphorous was introduced into the reaction chamber as an in situ dopant during the growth. The quality and orientation of the diamond thin films were monitored by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Current-voltage (I-V) data as a function of temperature for golddiamond film-silicon-aluminum structures were measured. The activation energy of the phosphorous dopants was calculated to be approximately 0.29 eV.

Wear and Nanomechanical Studies of Silicon Oxide and Silicon Nitride Thin Films for MEMS Applications

1998 ◽  
pp. 579-589 ◽  
Author(s):  
Z. Rymuza ◽  
Z. Kusznierewicz ◽  
M. Misiak ◽  
K. Schmidt-Szałowski ◽  
Z. Rżanek-Boroch ◽  
...  
Keyword(s):  
Thin Films ◽  
Silicon Nitride ◽  
Silicon Oxide

Epitaxial Ferroelectric BaTiO3 Thin Films for Microphotonic Applications

2000 ◽  
Vol 637 ◽  
Author(s):  
F. Niu ◽  
A.R. Teren ◽  
B.H. Hoerman ◽  
B.W. Wessels
Keyword(s):  
Thin Films ◽  
Chemical Vapor ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Insulating Layer ◽  
Ferroelectric State ◽  
Transmission Electron ◽  
Electro Optic ◽  
Metal Organic ◽  
Mgo Layers

AbstractEpitaxial ferroelectric BaTiO3 thin films have been developed as a material for microphotonics. Efforts have been directed toward developing these materials for thin film electro-optic modulators. Films were deposited by metalorganic chemical vapor deposition (MOCVD) on both MgO and silicon substrates. The electro-optic properties of the thin films were measured. For BaTiO3 thin films grown on (100) MgO substrates, the effective electro-optic coefficient, reff depended on the magnitude and direction of the electric field. Coefficients as high as 260 pm/V have been measured. Investigation of BaTiO3 films on silicon has been undertaken. Epitaxial BaTiO3 thin films were deposited by MOCVD on (100) MgO layers grown on silicon (100) substrates by metal-organic molecular beam epitaxy (MOMBE). The MgO serves as the low index optical cladding layer as well as an insulating layer. X-ray diffraction and transmission electron microscopy (TEM) indicated that BaTiO3 was epitaxial with an orientational relation given by BaTiO3 (100)//Si (100) and BaTiO3[011]//Si [011]. Polarization measurements indicated that the BaTiO3 epitaxial films on Si were in the ferroelectric state.

In Vivo Biostability of CVD Silicon Oxide and Silicon Nitride Films

2005 ◽  
Vol 872 ◽  
Author(s):  
John M. Maloney ◽  
Sara A. Lipka ◽  
Samuel P. Baldwin
Keyword(s):  
Chemical Vapor Deposition ◽  
Silicon Nitride ◽  
Vapor Deposition ◽  
Focused Ion Beam ◽  
Silicon Oxide ◽  
Ion Beam ◽  
Chemical Vapor ◽  
Silicon Chips ◽  
Silicon Nitride Films

AbstractLow pressure chemical vapor deposition (LPCVD) and plasma enhanced chemical vapor deposition (PECVD) silicon oxide and silicon nitride films were implanted subcutaneously in a rat model to study in vivo behavior of the films. Silicon chips coated with the films of interest were implanted for up to one year, and film thickness was evaluated by spectrophotometry and sectioning. Dissolution rates were estimated to be 0.33 nm/day for LPCVD silicon nitride, 2.0 nm/day for PECVD silicon nitride, and 3.5 nm/day for PECVD silicon oxide. A similar PECVD silicon oxide dissolution rate was observed on a silicon oxide / silicon nitride / silicon oxide stack that was sectioned by focused ion beam etching. These results provide a biostability reference for designing implantable microfabricated devices that feature exposed ceramic films.

Sign in / Sign up

Export Citation Format

Share Document