scholarly journals NUMERICAL SIMULATION OF THE DYNAMICS OF A FLEXIBLE ROTOR WITH TWO BALL AUTO-BALANCERS

2020 ◽  
pp. 31-44
Author(s):  
Nikolay Zaytsev ◽  
◽  
Denis Zaytsev ◽  
Andrey Makarov ◽  
Dmitriy Mineev ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Cross Sections ◽  
Experimental Studies ◽  
Element Model ◽  
Rolling Friction ◽  
Published Data ◽  
Flexible Rotor ◽  
Flexible Rotors ◽  
The Mathematical Model

Ball auto-balancing devices can to compensate changes of unbalance "on the move" only for rotors operating at supercritical speeds. For automatic balancing of such rotors, classified as flexible rotors, several auto-balancers located in different cross sections of the shaft are necessary. This makes it necessary to account bending fluctuations on studies of dynamics of the rotor with auto-balancers, that is especially important in the design of the real rotors. In view of the complexity of experimental studies of such rotors in the article the method of direct numerical simulation of the dynamics of the flexible rotor system – supports – auto-balances is considered. The methodological basis of this method is the use of a discrete multi-mass rotor model, which is equivalent in dynamic characteristics to a real rotor, and also the equations of dynamics of the system discrete rotor – supports – auto-balancers, obtained in the direct form of recording. For definition of discrete masses and a matrix of coefficients of influence of stiffness of rotor cross-sections it is supposed to use calculations for finite-element model of a real rotor by existing software complexes of the engineering analysis. The mathematical model of the system dynamics obtained by the Lagrange method takes into account the non-stationarity of the rotor rotation speed, the influence of gravity and the rolling friction of the balls in the auto-balancer cages. Verification of the mathematical model was performed by reproducing the published data using a computational model for a two-support single-disk three-mass rotor with a two-ball auto-balancer. For a four-mass rotor with two two-ball auto-balancers, the results of numerical simulation of dynamics for the modes of acceleration, steady-state rotation and deceleration are presented. It is shown that for the system under consideration, only partial auto-balancing takes place in the steady rotation mode, including after a stepwise increase of the imbalance.

Optimal Design of Dynamic Secondary Cooling of Continuous Casting

2012 ◽  
Vol 472-475 ◽  
pp. 1907-1910
Author(s):  
Yi Wang ◽  
Xin Jian Ma
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Finite Element ◽  
Continuous Casting ◽  
Cooling System ◽  
Solidification Process ◽  
Element Model ◽  
Secondary Cooling ◽  
The Mathematical Model ◽  
The Finite Element Model

Numerical simulation of the secondary cooling is applied to the design of continuous casting. The mathematical model for solidification process of the strand under air-mist was established and calculated with the finite element model. The model is used to calculate the feasible operating range of the continuous casting machines. The dynamic secondary cooling system has been analyzed with consideration of the thermo mechanical principles and numerical model. The adequacy of the model has been confirmed with experimental results.

EXPERIMENTAL STUDIES OF CAR PROPERTIES ON A PHYSICAL MODEL

2019 ◽  
pp. 10-16
Author(s):  
Oleksii Timkov ◽  
Dmytro Yashchenko ◽  
Volodymyr Bosenko
Keyword(s):  
Mathematical Model ◽  
Remote Control ◽  
Physical Model ◽  
Model Experiment ◽  
Experimental Studies ◽  
Electrical Energy ◽  
Short Term ◽  
Motor Current ◽  
Memory Card ◽  
The Mathematical Model

The article deals with the development of a physical model of a car equipped with measuring, recording and remote control equipment for experimental study of car properties. A detailed description of the design of the physical model and of the electronic modules used is given, links to application libraries and the code of the first part of the program for remote control of the model are given. Atmega microcontroller on the Arduino Uno platform was used to manage the model and register the parameters. When moving the car on the memory card saved such parameters as speed, voltage on the motor, current on the motor, the angle of the steered wheel, acceleration along three coordinate axes are recorded. Use of more powerful microcontrollers will allow to expand the list of the registered parameters of movement of the car. It is possible to measure the forces acting on the elements of the car and other parameters. In the future, it is planned to develop a mathematical model of motion of the car and check its adequacy in conducting experimental studies on maneuverability on the physical model. In addition, it is possible to conduct studies of stability and consumption of electrical energy. The physical model allows to quickly change geometric dimensions and mass parameters. In the study of highway trains, this approach will allow to investigate the various layout schemes of highway trains in the short term. It is possible to make two-axle road trains and saddle towed trains, three-way hitched trains of different layout. The results obtained will allow us to improve not only the mathematical model, but also the experimental physical model, and move on to further study the properties of hybrid road trains with an active trailer link. This approach allows to reduce material and time costs when researching the properties of cars and road trains. Keywords: car, physical model, experiment, road trains, sensor, remote control, maneuverability, stability.

MATHEMATICAL ANALYSIS OF THE ENDEMIC EQUILIBRIUM OF MALARIAHYGIENE MODEL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Oluwafemi Temidayo J. ◽  
Azuaba E. ◽  
Lasisi N. O.
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Equilibrium Point ◽  
Reproduction Number ◽  
Endemic Equilibrium ◽  
The Mathematical Model ◽  
Globally Stable ◽  
Well Posed ◽  
The Basic Reproduction Number ◽  
Invariant Principle

In this study, we analyzed the endemic equilibrium point of a malaria-hygiene mathematical model. We prove that the mathematical model is biological and meaningfully well-posed. We also compute the basic reproduction number using the next generation method. Stability analysis of the endemic equilibrium point show that the point is locally stable if reproduction number is greater that unity and globally stable by the Lasalle’s invariant principle. Numerical simulation to show the dynamics of the compartment at various hygiene rate was carried out.

Numerical Simulation of Subsea Cluster Manifold Installation by the Sheave Method

2018 ◽  
Author(s):  
Yu Zhao ◽  
Yingying Wang ◽  
Liwei Li ◽  
Chao Yang ◽  
Yang Du ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
South China Sea ◽  
Deep Sea ◽  
High Reliability ◽  
Two Dimensional ◽  
Complex Environment ◽  
Lumped Mass ◽  
Lumped Mass Method ◽  
The Mathematical Model

The sheave installation method (SIM) is an effective and non-conventional method to solve the installation of subsea equipment in deep water (>1000m), which has been developed to deploy the 175t Roncador Manifold I into 1,885 meters water depth in 2002. With the weight increment of subsea cluster manifold, how to solve its installation with the high reliability in the deep sea is still a great challenge. In this paper, the installation of the 300t subsea cluster manifold using the SIM is studied in the two-dimensional coordinate system. The mathematical model is established and the lumped mass method is used to calculate the hydrodynamic forces of the wireropes. Taking into account the complex environment loads, the numerical simulation of the lowering process is carried out by OrcaFlex. The displacement and vibration of the subsea cluster manifold in the z-axis direction and the effective tension at the top of the wireropes can be gotten, which can provide guidance for the installation of the cluster manifold in the South China Sea.

scholarly journals Population Behavior in the Mathematical Model of the Spread of COVID19 Type SEIRS

2021 ◽  
Vol 6 (2) ◽  
pp. 83-88
Author(s):  
Asmaidi As Med ◽  
Resky Rusnanda
Keyword(s):  
Mathematical Modeling ◽  
Numerical Simulation ◽  
Mathematical Model ◽  
Everyday Life ◽  
Applied Mathematics ◽  
Living Things ◽  
Simulation Results ◽  
Parameter Values ◽  
The Mathematical Model ◽  
Disease Free

Mathematical modeling utilized to simplify real phenomena that occur in everyday life. Mathematical modeling is popular to modeling the case of the spread of disease in an area, the growth of living things, and social behavior in everyday life and so on. This type of research is included in the study of theoretical and applied mathematics. The research steps carried out include 1) constructing a mathematical model type SEIRS, 2) analysis on the SEIRS type mathematical model by using parameter values for conditions 1and , 3) Numerical simulation to see the behavior of the population in the model, and 4) to conclude the results of the numerical simulation of the SEIRS type mathematical model. The simulation results show that the model stabilized in disease free quilibrium for the condition  and stabilized in endemic equilibrium for the condition .

scholarly journals Numerical simulation of changes in the electric properties of biological tissues under local heating by laser radiation

2021 ◽  
Vol 2090 (1) ◽  
pp. 012049
Author(s):  
N V Kovalenko ◽  
A V Smirnov ◽  
O A Ryabushkin
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Laser Radiation ◽  
Optical Radiation ◽  
Local Heating ◽  
Biological Tissues ◽  
Electric Properties ◽  
Reliable Tool ◽  
The Mathematical Model

Abstract The mathematical model that describes the local heating of biological tissues by optical radiation is introduced. Changes of the electric properties of biological tissues in such process can be used as a reliable tool for analyzing heating and damage degrees of tissues.

scholarly journals Mathematical modeling and harmonic analysis of SISFCL

2017 ◽  
Vol 36 (1) ◽  
pp. 258-270
Author(s):  
Debraj Sarkar ◽  
Debabrata Roy ◽  
Amalendu Bikash Choudhury ◽  
Sotoshi Yamada
Keyword(s):  
Mathematical Modeling ◽  
Mathematical Model ◽  
Harmonic Analysis ◽  
Voltage Drop ◽  
Element Model ◽  
Iron Core ◽  
Content Type ◽  
Hysteresis Characteristic ◽  
The Core ◽  
The Mathematical Model

Purpose A saturated iron core superconducting fault current limiter (SISFCL) has an important role to play in the present-day power system, providing effective protection against electrical faults and thus ensuring an uninterrupted supply of electricity to the consumers. Previous mathematical models developed to describe the SISFCL use a simple flux density-magnetic field intensity curve representing the ferromagnetic core. As the magnetic state of the core affects the efficient working of the device, this paper aims to present a novel approach in the mathematical modeling of the device with the inclusion of hysteresis. Design/methodology/approach The Jiles–Atherton’s hysteresis model is utilized to develop the mathematical model of the limiter. The model is numerically solved using MATLAB. To support the validity of model, finite element model (FEM) with similar specifications was simulated. Findings Response of the limiter based on the developed mathematical model is in close agreement with the FEM simulations. To illustrate the effect of the hysteresis, the responses are compared by using three different hysteresis characteristics. Harmonic analysis is performed and comparison is carried out utilizing fast Fourier transform and continuous wavelet transform. It is observed that the core with narrower hysteresis characteristic not only produces a better current suppression but also creates a higher voltage drop across the DC source. It also injects more harmonics in the system under fault condition. Originality/value Inclusion of hysteresis in the mathematical model presents a more realistic approach in the transient analysis of the device. The paper provides an essential insight into the effect of the core hysteresis characteristic on the device performance.

scholarly journals On Numerical Simulation Approach for Multiple Resonance Modes in Servo Systems

2017 ◽  
Vol 2017 ◽  
pp. 1-7
Author(s):  
Qixin Zhu ◽  
Hongli Liu ◽  
Yiyi Yin ◽  
Lei Xiong ◽  
Yonghong Zhu
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Closed Loop ◽  
Resonance Mode ◽  
Servo Control ◽  
Simulation Approach ◽  
Servo Systems ◽  
Resonance Modes ◽  
Resonant Part ◽  
The Mathematical Model

Mechanical resonance is one of the most pervasive problems in servo control. Closed-loop simulations are requisite when the servo control system with high accuracy is designed. The mathematical model of resonance mode must be considered when the closed-loop simulations of servo systems are done. There will be a big difference between the simulation results and the real actualities of servo systems when the resonance mode is not considered in simulations. Firstly, the mathematical model of resonance mode is introduced in this paper. This model can be perceived as a product of a differentiation element and an oscillating element. Secondly, the second-order differentiation element is proposed to simulate the resonant part and the oscillating element is proposed to simulate the antiresonant part. Thirdly, the simulation approach for two resonance modes in servo systems is proposed. Similarly, this approach can be extended to the simulation of three or even more resonances in servo systems. Finally, two numerical simulation examples are given.

scholarly journals Use of the mathematical model of the ignition system to analyze the spark discharge, including the destruction of spark plug electrodes

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 57-62 ◽  
Author(s):  
Sebastian Różowicz
Keyword(s):  
Mathematical Model ◽  
Experimental Studies ◽  
Fuel Mixture ◽  
Spark Discharge ◽  
Fuel Additives ◽  
Ignition System ◽  
Spark Plug ◽  
The Mathematical Model

Abstract The paper presents the results of analytical and experimental studies concerning the influence of different kinds of fuel additives on the quality of the spark discharge for different configurations of the ignition system. The wear of the spark plug electrode and the value of spark discharge were determined for various impurities and configurations of the air-fuel mixture.

Dynamics of Shock Waves in the Cylindrical Channel With Confusers

2009 ◽  
Vol 4 (2) ◽  
pp. 13-18
Author(s):  
Igor Anufriev ◽  
Aleksandr Golovanov ◽  
Aleksandr Tsimbalyuk ◽  
Oleg Sharypov
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Shock Wave ◽  
Shock Wave Front ◽  
Gas Flow ◽  
Cylindrical Channel ◽  
Maximal Pressure ◽  
The Mathematical Model ◽  
Forest Combustible ◽  
Gunpowder Charge

Current work covers experimental and theoretical investigation of conic confusers impact on the intensity shock wave, generated in the shock tube by explosion of gunpowder charge. For given conditions optimal geometric characteristics of the confuser, providing maximal pressure in the shock wave front, were found experimentally. The mathematical model was developed and numerical simulation of the axisymmetric shock-wave gas flow in the channel was carried out. Experimentally was shown, that the application of the optimal confuser provides significant increase of the efficiency gasdynamic effect on the combustion of forest combustible materials.

Sign in / Sign up

Export Citation Format

Share Document