scholarly journals Preliminary Study of the Rheological and Mechanical Properties of Alkali-activated Concrete Based on Tungsten Mining Waste Mud

2020 ◽  
Author(s):  
Abdelhakim Benhamouda ◽  
João Castro-Gomes
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Rheological Behaviour ◽  
Coarse Sand ◽  
Mining Waste ◽  
Binder Phase ◽  
Portland Cement Concrete ◽  
Alkali Activated Concrete ◽  
Alkali Activated

The rheological properties of Portland cement (PC) concrete have been extensively studied and compared with those of alkali-activated concrete (AAC). This study discusses the effect of the liquid to solid ratio on the rheological and mechanical properties of AAM concrete, based on mining waste mud as the binder phase, and compares them with those of Portland cement concrete (PCC). The AAM concrete studied is a mix of coarse aggregate 6/15, two types of sand (finer and coarse sand), and a precursor. The precursor is a mix of 70% tungsten mining waste mud, 15% waste glass and 15% metakaolin. This mix was activated by a combination of sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) and the PCC was a mix of the same aggregate but with cement as binder and water as a liquid. The activator/precursor ratio was studied 0.5, 0.52, 0.54, 0.56 and 0.58. The results obtained show a similar rheological behaviour between AAC and PCC, the workability affected by L/S increases with the increasing ratio L/S in AAC and for L/S=0.5 slump was 6 cm and was 16 cm for L/S =0.58. Regarding the mechanical properties, the results obtained in 7 days showed similar performance in AAC and PCC. The compressive strength also decreases with the increasing of L/S, in AAC with L/S=0.5 the compressive strength was 15.9 MPa and for L/S =0.58 was 10.5. Keywords: Tungsten mining waste, Rheology, Mechanical properties, Portland cement, alkali-activated concrete

scholarly journals Rheology, Mechanical Properties and Porosity of Ternary Alkali-Activated Binders Based on Mining Mud Waste with Waste Glass and Metakaolin

CivilEng ◽  
2021 ◽  
Vol 2 (1) ◽  
pp. 236-253
Author(s):  
Abdelhakim Benhamouda ◽  
João Castro-Gomes ◽  
Luiz Pereira-de-Oliveira
Keyword(s):  
Mechanical Properties ◽  
Portland Cement ◽  
Yield Stress ◽  
Relative Yield ◽  
Rheological Behaviour ◽  
Waste Glass ◽  
Plastic Viscosity ◽  
Rheological Parameters ◽  
Alkali Activated Binders ◽  
Alkali Activated

Alkali-activated materials have the potential to replace Portland cement in certain applications. To better understand these binders’ properties, it is relevant to study their rheological behaviour at early ages, like in the case of Portland cement paste. There are already many studies on the rheological behaviour of these materials in the available literature, using fly ash, metakaolin, and ground granulated blast furnace slag as precursors. However, this study discusses the rheological behaviour, mechanical properties, and porosity of ternary alkali-activated binders based on mining mud waste, waste glass, and metakaolin. The precursor consisted of a volume mix of 70% of tungsten mining waste mud, 15% glass waste, and 15% of metakaolin. The activator was a combination of sodium hydroxide and sodium silicate solution. Five activator/precursor (A/P) ratios (0.37, 0.38, 0.39, 0.40, and 0.4) were studied. The result showed that the activator/precursor ratio affects the rheology of paste and their rheological behaviour fit the Bingham model. The relative yield stress (g) and plastic viscosity (h) increased inversely with the A/P ratio, while the workability increased proportionally. Furthermore, some empirical models are proposed to describe the characteristic of yield stress: plastic viscosity and spread diameter versus the A/P ratio and time with a correlation between the rheological parameters and the spread diameter. The increase in A/P ratio has also followed a decrease in compressive strength in all tested samples for all the ages. As expected, an increase of the porosity accompanied the increase of the A/P ratio.

scholarly journals Some Mechanical Properties of Cement Treated Base (CTB) Incorporating Waste Portland Cement Concrete Under Different Corresponding Conditions

2018 ◽  
Vol 7 (4.37) ◽  
pp. 138
Author(s):  
Asst. Prof. Dr. Khawla H. H. Shubber ◽  
Eng. Sajjad Hashim Mohamed
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Granular Materials ◽  
Compression Strength ◽  
Cement Content ◽  
Strength Increase ◽  
Test Results ◽  
Portland Cement Concrete ◽  
Cement Concrete

This research represents a trial of understanding and improving mechanical properties of base or subbase granular materials, used in pavement construction, stabilized with Portland cement known as cement treated base (CTB) in terms of density, optimum water content (O.W.C), and compression Strength of three curing ages (3, 7, 28) days under different situations. Different Portland cement percent of (0, 5, 7, 10, 12, and 15) % by weight were added to selected base course granular materials (type B according to local standard specification in Iraq). Results showed that the density of mixture increase with increasing added cement percent, while O.W.C takes its maximum value around 7% cement content, and compression strength increase with increasing cement content and curing age. Then effect of replacing 50% of natural granular materials by waste Portland cement concrete (WPCC) was investigated on the results of (0, 7& 15)% cement content on density, O.W.C and compression strength in the three curing ages. Results reveled although density of mixture cooperating WPCC for 0% cement content was higher, CTB of natural granular material were denser. On the other hand compressive strength decrease in case of using WPCC for all percent cement added and curing ages. Finally, effect of soaking in water on CTB with (7 &15)% cement compressive strength of three curing ages was studied, under three period of soaking (1 week, 2 weeks, &one month). Test results exposed that, CTB Compressive strength increase with increasing soaking period but still less than that of un-soaked and for all curing ages. For each test stage mathematics relationships with acceptable correlation were presented proofing test results tendency.  

Mechanical Properties of Alite-Calcium Barium Sulphoaluminate Cement Concrete

2008 ◽  
Vol 400-402 ◽  
pp. 121-124
Author(s):  
Zong Hui Zhou ◽  
Ling Chao Lu ◽  
Xing Kai Gao ◽  
Xin Cheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Portland Cement ◽  
Cement Paste ◽  
Early Age ◽  
Hardened Cement ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Hardened Cement Paste ◽  
Sulphoaluminate Cement

In this paper, preparation and mechanical properties of Alite-calcium barium sulphoaluminate (Alite-C2.75B1.25A3 ) cement concrete were studied. The results showed the compressive strength of Alite-C2.75B1.25A3 cement concrete was much higher than that of Portland cement concrete, especially the early-age compressive strength. The 24-hour compressive strength of Alite-C2.75B1.25A3 cement concrete could reach 22.81Mpa for w/c=0.45, 17.29Mpa for w/c=0.50 and 17.04Mpa for w/c=0.55 respectively. They were about 50 to 65 percent higher than those of Portland cement concrete. The 7-day compressive strength could reach about 80 to 90 percent of 28-day strength for Alite-C2.75B1.25A3 cement concrete. The 28-day strength could reach 55.85Mpa for w/c=0.45, 48.01Mpa for w/c=0.50 and 44.21Mpa for w/c=0.55 respectively. The results of SEM showed the interfaces between the hardened cement paste and aggregates in Alite-C2.75B1.25A3 cement concrete were more compact than those in Portland cement concrete. Distribution of particulate bulk was more uniformity and a majority of clinker particles was wrapped by hydrated gel in Alite-C2.75B1.25A3 concrete. And, the structure of Alite-C2.75B1.25A3 cement concrete was much more compact than that of Portland cement concrete.

Effect of Specimen Size and Curing Condition on the Compressive Strength of Alkali-Activated Concrete

2017 ◽  
Vol 2629 (1) ◽  
pp. 9-14 ◽  
Author(s):  
Robert James Thomas ◽  
Sulapha Peethamparan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Specimen Size ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Slag Cement ◽  
Fly Ash Concrete ◽  
Activated Slag ◽  
Alkali Activated Concrete ◽  
Alkali Activated

Alkali-activated concrete is a rapidly emerging sustainable alternative to portland cement concrete. The compressive strength behavior of alkali-activated concrete has been reported by various studies to a limited extent, but these discussions have been based on minimal evidence. Furthermore, although it is known that specimen size has a distinct effect on the apparent compressive strength of concrete, this effect has yet to be modeled for alkali-activated concrete. This paper presents the results of a comprehensive study of the effects of curing condition (i.e., moist-cured at ambient temperature for 28 days or heat-cured at 50çC for 48 h) and specimen size on the compressive strength of sodium silicate–activated fly ash and slag cement concrete. The heat-cured strength of alkali-activated slag cement concrete was linearly related to the moist-cured strength; the former was about 5% greater than the latter. Heat curing also improved the strength of alkali-activated fly ash concrete, although the effect was greatly magnified for lower-strength mixtures and was much less significant at higher strengths. Existing size effect laws employed for portland cement concrete proved reasonably accurate in describing the effect of specimen size on the apparent strength of alkali-activated slag cement concrete. However, these existing models greatly underestimated the size effect in alkali-activated fly ash concrete; the authors suggest that this finding was the result of significant microcracking in the alkali-activated fly ash concrete.

Study of Mechanical Properties and Physical Properties of Rubberized Portland Cement Concrete

2012 ◽  
Vol 512-515 ◽  
pp. 2812-2816
Author(s):  
Wei Li ◽  
Xiao Chu Wang ◽  
Hong Tao Liu
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Portland Cement ◽  
Silica Fume ◽  
Rubber Particle ◽  
Portland Cement Concrete ◽  
Cement Concrete ◽  
Cleavage Strength ◽  
Research Situation

This test summers up the research situation of rubber powder modifier. According to tests of density, flexural strength, compressive strength and cleavage strength, this test analyzes the basic mechanical properties and the variation of rubberized portland cement concrete which is mixing the silica fume modifier. The results show that the flexural strength, compressive strength and cleavage strength of concrete may increase when silica fume concrete admixture modifiers is mixed in cement concrete. The workability, density, flexural strength, compressive strength, ratio of compressive strength and cleavage strength of rubberized portland cement concrete gradually reduced with the increase in dosage of rubber. The rubber particles mixed with concrete which can when the rubber particle size is not more than 30% of the dosage of coarse aggregate, the fine pavement of rubberized portland cement concrete can be got.

Sign in / Sign up

Export Citation Format

Share Document