Rozwiązania techniczne i technologiczne końcowego wyposażenia odwiertów z odcinkiem odchylonym i horyzontalnym w odwiertach na Niżu Polskim

Nafta-Gaz ◽  
2021 ◽  
Vol 77 (8) ◽  
pp. 529-540
Author(s):  
Marian Wolan ◽  
Keyword(s):  
Carbonate Reservoir ◽  
Common Elements ◽  
Rock Layer ◽  
Reservoir Rocks ◽  
Fracture Pressure ◽  
Reservoir Conditions ◽  
Cap Rock ◽  
High Concentrations ◽  
Very High ◽  
Selection Of

The article covers typical problems during realization of completion projects in the Polish Lowlands. It also presents harsh reservoir conditions encountered at the time of completion. Very high pressure gradient (over 0.021 MPa/m), relatively small thickness of cap rock layer, small differences between hydrostatic pressure and fracture pressure and high concentrations of CO2 and H2S require experience and knowledge when completing the wells. The article discusses the main functions and most common elements of completion assembly. Only a few sample completion assemblies that are used in boreholes in the Polish Lowlands are presented. Each element is described with emphasis placed on its tasks and advantages during completion, production phase of the well, as well as during workover and abandonment operations in the well. Some completion schemes common in the Polish Lowlands are presented together with their advantages and capabilities depending on final equipment used for completion and its location in the completion assembly. Selection of materials and elastomers used in completion assembly is shown depending on reservoir conditions. The article also presents a brief analysis of stresses that can occur in completion assembly during stimulation treatments, e.g. during acidizing of carbonate reservoir rocks, killing the well, operation of the well. Tools and equipment necessary for completing the well, determined by well construction and well conditions are described. Wells have been divided into two types depending on the trajectory of the well, up to 30° and above 30°, which influences the selection of equipment used to perform the operations of controlling the elements of the final completion assembly of the wells. It was emphasized that the selection of equipment to control the above-mentioned elements also depends on other conditions, such as the parameters of the fluid in which these operations are performed or the depth. The article also outlines the procedures necessary before and during the installation of the completion assembly.

Der Sommer und Herbst 2003 aus phänologischer Sicht | Summer and autumn 2003 from a phenological point of view

2004 ◽  
Vol 155 (5) ◽  
pp. 142-145 ◽  
Author(s):  
Claudio Defila
Keyword(s):  
Time Series ◽  
New Record ◽  
Point Of View ◽  
Late Spring ◽  
Mean Deviation ◽  
Leaf Shedding ◽  
The Mean ◽  
Very High ◽  
Selection Of

The record-breaking heatwave of 2003 also had an impact on the vegetation in Switzerland. To examine its influences seven phenological late spring and summer phases were evaluated together with six phases in the autumn from a selection of stations. 30% of the 122 chosen phenological time series in late spring and summer phases set a new record (earliest arrival). The proportion of very early arrivals is very high and the mean deviation from the norm is between 10 and 20 days. The situation was less extreme in autumn, where 20% of the 103 time series chosen set a new record. The majority of the phenological arrivals were found in the class «normal» but the class«very early» is still well represented. The mean precocity lies between five and twenty days. As far as the leaf shedding of the beech is concerned, there was even a slight delay of around six days. The evaluation serves to show that the heatwave of 2003 strongly influenced the phenological events of summer and spring.

Late Permian carbonate concretions in the marine siliciclastic sediments of the Ravnefjeld Formation, East Greenland

2002 ◽  
pp. 126-132
Author(s):  
Jesper Kresten Nielsen ◽  
Nils-Martin Hanken
Keyword(s):  
Mineral Resources ◽  
Sedimentary Basins ◽  
Sedimentary Facies ◽  
Carbonate Reservoir ◽  
Upper Permian ◽  
Late Permian ◽  
East Greenland ◽  
Reservoir Rocks ◽  
Carbonate Concretions ◽  
Siliciclastic Sediments

NOTE: This article was published in a former series of GEUS Bulletin. Please use the original series name when citing this article, for example: Kresten Nielsen, J., & Hanken, N.-M. (2002). Late Permian carbonate concretions in the marine siliciclastic sediments of the Ravnefjeld Formation, East Greenland. Geology of Greenland Survey Bulletin, 191, 126-132. https://doi.org/10.34194/ggub.v191.5140 _______________ This investigation of carbonate concretions from the Late Permian Ravnefjeld Formation in East Greenland forms part of the multi-disciplinary research project Resources of the sedimentary basins of North and East Greenland (TUPOLAR; Stemmerik et al. 1996, 1999). The TUPOLAR project focuses on investigations and evaluation of potential hydrocarbon and mineral resources of the Upper Permian – Mesozoic sedimentary basins. In this context, the Upper Permian Ravnefjeld Formation occupies a pivotal position because it contains local mineralisations and has source rock potential for hydrocarbons adjacent to potential carbonate reservoir rocks of the partly time-equivalent Wegener Halvø Formation (Harpøth et al. 1986; Surlyk et al. 1986; Stemmerik et al. 1998; Pedersen & Stendal 2000). A better understanding of the sedimentary facies and diagenesis of the Ravnefjeld Formation is therefore crucial for an evaluation of the economic potential of East Greenland.

The Effects of Shock Vancomycin Concentrations on the Formation of Heteroresistance in Staphylococcus aureus

2020 ◽  
Vol 65 (9-10) ◽  
pp. 3-7
Author(s):  
V. V. Gostev ◽  
Yu. V. Sopova ◽  
O. S. Kalinogorskaya ◽  
M. E. Velizhanina ◽  
I. V. Lazareva ◽  
...  
Keyword(s):  
Staphylococcus Aureus ◽  
In Vitro Selection ◽  
Methicillin Resistant Staphylococcus Aureus ◽  
High Concentration ◽  
Short Term ◽  
High Concentrations ◽  
Selection Of ◽  
Selection Of Resistance ◽  
Test Cultures

Glycopeptides are the basis of the treatment of infections caused by MRSA (Methicillin-Resistant Staphylococcus aureus). Previously, it was demonstrated that antibiotic tolerant phenotypes are formed during selection of resistance under the influence of high concentrations of antibiotics. The present study uses a similar in vitro selection model with vancomycin. Clinical isolates of MRSA belonging to genetic lines ST8 and ST239, as well as the MSSA (ATCC29213) strain, were included in the experiment. Test isolates were incubated for five hours in a medium with a high concentration of vancomycin (50 μg/ml). Test cultures were grown on the medium without antibiotic for 18 hours after each exposure. A total of ten exposure cycles were performed. Vancomycin was characterized by bacteriostatic action; the proportion of surviving cells after exposure was 70–100%. After selection, there was a slight increase in the MIC to vancomycin (MIC 2 μg/ml), teicoplanin (MIC 1.5–3 μg/ml) and daptomycin (MIC 0.25–2 μg/ml). According to the results of PAP analysis, all strains showed an increase in the area under curve depending on the concentration of vancomycin after selection, while a heteroresistant phenotype (with PAP/AUC 0.9) was detected in three isolates. All isolates showed walK mutations (T188S, D235N, E261V, V380I, and G223D). Exposure to short-term shock concentrations of vancomycin promotes the formation of heteroresistance in both MRSA and MSSA. Formation of VISA phenotypes is possible during therapy with vancomycin.

The metachor as a characteristic of the association of electrolytes in aqueous solutions

1984 ◽  
Vol 49 (5) ◽  
pp. 1061-1078 ◽  
Author(s):  
Jiří Čeleda ◽  
Stanislav Škramovský
Keyword(s):  
Aqueous Solutions ◽  
Apparent Volume ◽  
Solutions Of Electrolytes ◽  
Molal Volumes ◽  
The Difference ◽  
High Concentrations ◽  
Experimental Values ◽  
Suitable Characteristic ◽  
Association Of Ions ◽  
Very High

Based on the earlier paper introducing a concept of the apparent parachor of a solute in the solution, we have eliminated in the present work algebraically the effect which is introduced into this quantity by the additivity of the apparent molal volumes. The difference remaining from the apparent parachor after substracting the contribution corresponding to the apparent volume ( for which the present authors suggest the name metachor) was evaluated from the experimental values of the surface tension of aqueous solutions for a set of 1,1-, 1,2- and 2,1-valent electrolytes. This difference showed to be independent of concentration up to the very high values of the order of units mol dm-3 but it was directly proportional to the number of the free charges (with a proportionality factor 5 ± 1 cm3 mol-1 identical for all studied electrolytes). The metachor can be, for this reason, a suitable characteristic for detection of the association of ions and formation of complexes in the solutions of electrolytes, up to high concentrations where other methods are failing.

scholarly journals Nitrification Process in a Nuclear Wastewater with High Load of Nitrogen, Uranium and Organic Matter under ORP Controlled

Water ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1607
Author(s):  
Mariano Venturini ◽  
Ariana Rossen ◽  
Patricia Silva Paulo
Keyword(s):  
Ammonia Oxidation ◽  
High Load ◽  
Nuclear Fuels ◽  
Monod Model ◽  
Nernst Equation ◽  
Nitrification Process ◽  
Real Wastewater ◽  
High Concentrations ◽  
Wastewater Samples ◽  
Very High

To produce nuclear fuels, it is necessary to convert uranium′s ore into UO2-ceramic grade, using several quantities of kerosene, methanol, nitric acid, ammonia, and, in low level, tributyl phosphate (TBP). Thus, the effluent generated by nuclear industries is one of the most toxic since it contains high concentrations of dangerous compounds. This paper explores biological parameters on real nuclear wastewater by the Monod model in an ORP controlled predicting the specific ammonia oxidation. Thermodynamic parameters were established using the Nernst equation to monitor Oxiders/Reductors relationship to obtain a correlation of these parameters to controlling and monitoring; that would allow technical operators to have better control of the nitrification process. The real nuclear effluent is formed by a mixture of two different lines of discharges, one composed of a high load of nitrogen, around 11,000 mg/L (N-NH4+-N-NO3−) and 600 mg/L Uranium, a second one, proceeds from uranium purification, containing TBP and COD that have to be removed. Bioprocesses were operated on real wastewater samples over 120 days under controlled ORP, as described by Nernst equations, which proved to be a robust tool to operate nitrification for larger periods with a very high load of nitrogen, uranium, and COD.

scholarly journals Halogenated Volatile Organic Compounds in Water Samples and Inorganic Elements Levels in Ores for Characterizing a High Anthropogenic Polluted Area in the Northern Latium Region (Italy)

2021 ◽  
Vol 18 (4) ◽  
pp. 1628
Author(s):  
Mario Vincenzo Russo ◽  
Ivan Notardonato ◽  
Alberto Rosada ◽  
Giuseppe Ianiri ◽  
Pasquale Avino
Keyword(s):  
Organic Compounds ◽  
Mean Value ◽  
Greenhouse Crops ◽  
River Waters ◽  
Liquid Liquid Extraction ◽  
Volatile Organic ◽  
High Concentrations ◽  
Very High ◽  
Inorganic Fraction

This paper shows a characterization of the organic and inorganic fraction of river waters (Tiber and Marta) and ores/soil samples collected in the Northern Latium region of Italy for evaluating the anthropogenic/natural source contribution to the environmental pollution of this area. For organic compounds, organochloride volatile compounds in Tiber and Marta rivers were analyzed by two different clean-up methods (i.e., liquid–liquid extraction and static headspace) followed by gas chromatography–electron capture detector (GC-ECD) analysis. The results show very high concentrations of bromoform (up to 1.82 and 3.2 µg L−1 in Tiber and Marta rivers, respectively), due to the presence of greenhouse crops, and of chloroform and tetrachloroethene, due to the presence of handicrafts installations. For the qualitative and quantitative assessment of the inorganic fraction, it is highlighted the use of a nuclear analytical method, instrumental neutron activation analysis, which allows having more information as possible from the sample without performing any chemical-physical pretreatment. The results have evidenced high levels of mercury (mean value 88.6 µg g−1), antimony (77.7 µg g−1), strontium (12,039 µg g−1) and zinc (103 µg g−1), whereas rare earth elements show levels similar to the literature data. Particular consideration is drawn for arsenic (414 µg g−1): the levels found in this paper (ranging between 1 and 5100 µg g−1) explain the high content of such element (as arsenates) in the aquifer, a big issue in this area.

scholarly journals Joint universal modular plasmids (JUMP): a flexible vector platform for synthetic biology

2021 ◽  
Vol 6 (1) ◽  
Author(s):  
Marcos Valenzuela-Ortega ◽  
Christopher French
Keyword(s):  
Copy Number ◽  
Life Science ◽  
Insertion Site ◽  
Golden Gate ◽  
Common Elements ◽  
Modern Life ◽  
Specific Host ◽  
Modular Cloning ◽  
Golden Gate Cloning ◽  
Selection Of

Abstract Generation of new DNA constructs is an essential process in modern life science and biotechnology. Modular cloning systems based on Golden Gate cloning, using Type IIS restriction endonucleases, allow assembly of complex multipart constructs from reusable basic DNA parts in a rapid, reliable and automation-friendly way. Many such toolkits are available, with varying degrees of compatibility, most of which are aimed at specific host organisms. Here, we present a vector design which allows simple vector modification by using modular cloning to assemble and add new functions in secondary sites flanking the main insertion site (used for conventional modular cloning). Assembly in all sites is compatible with the PhytoBricks standard, and vectors are compatible with the Standard European Vector Architecture (SEVA) as well as BioBricks. We demonstrate that this facilitates the construction of vectors with tailored functions and simplifies the workflow for generating libraries of constructs with common elements. We have made available a collection of vectors with 10 different microbial replication origins, varying in copy number and host range, and allowing chromosomal integration, as well as a selection of commonly used basic parts. This design expands the range of hosts which can be easily modified by modular cloning and acts as a toolkit which can be used to facilitate the generation of new toolkits with specific functions required for targeting further hosts.

THE SELECTIVE PROTEOLYTIC ENZYME INHIBITORY ACTION OF BENZETHONIUM CHLORIDE

1960 ◽  
Vol 38 (1) ◽  
pp. 25-32 ◽  
Author(s):  
Ivan T. Beck ◽  
E. Pinter ◽  
R. D. McKenna ◽  
H. Griff
Keyword(s):  
Subcutaneous Injection ◽  
Proteolytic Enzyme ◽  
Inhibitory Action ◽  
Hemorrhagic Pancreatitis ◽  
Benzethonium Chloride ◽  
Tryptic Activity ◽  
High Concentrations ◽  
Acute Hemorrhagic Pancreatitis ◽  
Very High

Acute hemorrhagic pancreatitis in humans is thought to be perpetuated by the autolytic processes catalyzed by trypsin and lipase. This study is an integral part of our search for trypsin and lipase inhibitors to be used in the treatment of this disease.Benzethonium chloride was found to inhibit tryptic activity in vitro. The proteolytic activity of rabbit's serum was inhibited, and the inhibition was most pronounced 6 to 12 hours after the subcutaneous injection of the compound. Fibrinolysin was also inhibited in vitro but benzethonium chloride had no inhibitory action on chymotrypsin, pepsin, or lipase.Serum proteins in vitro were precipitated only with very high concentrations of the compound. No significant protein changes were observed in sera of rabbits after the subcutaneous injection of the compound.

Integrated Usage of Surveillance Data for Estimating Cap Rock Integrity and Heat Distribution during Steam Injection in a Fractured Carbonate Reservoir

2010 ◽  
Author(s):  
Stan Schoofs ◽  
Mohamed Hassan Ali Al-Lawati ◽  
Geir Engen ◽  
Khalid Al Salmi ◽  
Issa Al Quseimi ◽  
...  
Keyword(s):  
Steam Injection ◽  
Carbonate Reservoir ◽  
Surveillance Data ◽  
Heat Distribution ◽  
Fractured Carbonate ◽  
Cap Rock
Sign in / Sign up

Export Citation Format

Share Document