Influence of Inlet Charge Swirl on Fuel-Economic and Environmental Indicators of a Gas-Piston Engine

2020 ◽  
pp. 131-146
Author(s):  
P.S. Patsey ◽  
Yu.V. Galyshev ◽  
A.B. Zaytsev ◽  
A.Yu. Shabanov
Keyword(s):  
Turbulent Flow ◽  
Combustion Chamber ◽  
Vortex Motion ◽  
Spark Ignition ◽  
Environmental Indicators ◽  
Piston Engine ◽  
Inlet Channel ◽  
Physicochemical Processes ◽  
Gas Fuel ◽  
Ignition Kernel

The paper introduces the results of studying the influence of intake ports shape on turbulization and charge swirl in the combustion chamber, combustion rate, ecological and indicator values of the engine. The study was carried out using mathematical simulation of physicochemical processes occurring in the combustion chamber of a piston engine during gas fuel combustion. The turbulent flow of the mixture, spark ignition and combustion of gas fuel are simulated. To simulate the turbulent flow, the RNG (k--ε)-model was used, to simulate the combustion of natural gas in the combustion chamber a model based on the specific surface area of the flame, the so-called G-equation model, was used. When simulating spark ignition, the model of discrete particles of the ignition kernel DPIK (Discrete Particle Ignition Kernel) was applied. As a result of simulation, we found that replacing one inlet channel with a tangential channel allows creating a vortex motion and increasing the turbulence of the mixture in the combustion chamber. An increase in the kinetic energy of the mixture before the spark is applied leads to a decrease in the combustion time. The use of swirling the charge on inlet by replacing one filling channel with a tangential one can significantly improve the environmental performance of the engine while maintaining fuel and economic indicators. The ANSYS Forte program was used to simulate the physicochemical processes in the combustion chamber

Prediction of gaseous pollutant emissions from a spark-ignition direct-injection engine with gas-exchange simulation

2021 ◽  
pp. 146808742110050
Author(s):  
Stefania Esposito ◽  
Lutz Diekhoff ◽  
Stefan Pischinger
Keyword(s):  
Gas Exchange ◽  
Combustion Chamber ◽  
Direct Injection ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Operating Parameters ◽  
Gaseous Pollutant ◽  
Fuel Ratio ◽  
No Emissions

With the further tightening of emission regulations and the introduction of real driving emission tests (RDE), the simulative prediction of emissions is becoming increasingly important for the development of future low-emission internal combustion engines. In this context, gas-exchange simulation can be used as a powerful tool for the evaluation of new design concepts. However, the simplified description of the combustion chamber can make the prediction of complex in-cylinder phenomena like emission formation quite challenging. The present work focuses on the prediction of gaseous pollutants from a spark-ignition (SI) direct injection (DI) engine with 1D–0D gas-exchange simulations. The accuracy of the simulative prediction regarding gaseous pollutant emissions is assessed based on the comparison with measurement data obtained with a research single cylinder engine (SCE). Multiple variations of engine operating parameters – for example, load, speed, air-to-fuel ratio, valve timing – are taken into account to verify the predictivity of the simulation toward changing engine operating conditions. Regarding the unburned hydrocarbon (HC) emissions, phenomenological models are used to estimate the contribution of the piston top-land crevice as well as flame wall-quenching and oil-film fuel adsorption-desorption mechanisms. Regarding CO and NO emissions, multiple approaches to describe the burned zone kinetics in combination with a two-zone 0D combustion chamber model are evaluated. In particular, calculations with reduced reaction kinetics are compared with simplified kinetic descriptions. At engine warm operation, the HC models show an accuracy mainly within 20%. The predictions for the NO emissions follow the trend of the measurements with changing engine operating parameters and all modeled results are mainly within ±20%. Regarding CO emissions, the simplified kinetic models are not capable to predict CO at stoichiometric conditions with errors below 30%. With the usage of a reduced kinetic mechanism, a better prediction capability of CO at stoichiometric air-to-fuel ratio could be achieved.

scholarly journals Phenomenological model for determining velocity field of LPG jet in combustion chamber of direct injection S.I. engine

2004 ◽  
Vol 26 (2) ◽  
pp. 83-92
Author(s):  
Bui Van Ga ◽  
Phung Xuan Tho ◽  
Nhan Hong Quang ◽  
Nguyen Huu Huong
Keyword(s):  
Combustion Chamber ◽  
Phenomenological Model ◽  
Direct Injection ◽  
Spark Ignition ◽  
Velocity Profiles ◽  
Gas Jet ◽  
Liquefied Petroleum Gas ◽  
Si Engine ◽  
Si Engines ◽  
Stratified Combustion

A phenomenological model has been established to predict the velocity distribution of LPG (Liquefied Petroleum Gas) jet in combustion chamber of spark ignition (SI) engine. A shaped coefficient \(\beta\) governing the similarity of velocity profiles of LPG jets has been defined based on the theoretical and experimental analyses of turbulent diffusion jets. The results show that \(\beta\) is constant for steady jet but it is not the case for unsteady one. The model will enable us to calculate the velocity profiles of LPG jet after ending injection. This is necessary for research of stratified combustion in direct injection LPG SI engines.

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural Gas Spark Ignition

2018 ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Spark Timing ◽  
Heavy Duty Diesel

Increased utilization of natural-gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduce greenhouse-gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOx, CO, and HC emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing, engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late burn (including double-peak heat release rate) was observed for advanced spark timing. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3 %), moderate rate of pressure rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Simulation of Altitude Influence on Piston Ring Movement and Blow-By Effects in Piston Engines (Keynote)

2003 ◽  
Author(s):  
Sylvester Abanteriba
Keyword(s):  
Combustion Chamber ◽  
Piston Ring ◽  
Cylinder Liner ◽  
Lubricating Oil ◽  
Axial Position ◽  
Piston Engine ◽  
Piston Rings ◽  
Ability To Act ◽  
Effective Seal ◽  
The Impact

The compression and oil rings of the piston engine play a very important role in the performance and reliability of the piston engine. The rings are required to accomplish three main distinct tasks: 1. Sealing the combustion chamber gas from the crankcase to eliminate blow-by phenomenon, which constitutes the flow of some of the contents of the combustion chamber into the crankcase. 2. Proper distribution of the lubricating oil film over the piston skirt and cylinder liner. 3. Transfer of heat from piston to cylinder liner. Unfortunately the piston ring pack contributes to the highest proportion of the frictional losses in the engine and is more prone to high wear rates. In the engine, the compression rings are designed to provide effective sealing of the crankcase against the gases from the combustion chamber. The oil-rings provide an effective means of distributing the lubricating oil over the cylinder liner while keeping it from flowing into the combustion chamber. The ability of the compression rings to serve as a gas seal depends on their axial position within the groove. The ring needs to be in contact with the lower flank in order to provide the requisite sealing effect. Once the ring lifts itself from the lower flank its ability to act as an effective seal is compromised. The axial motion of the piston rings during the operation of the engine engenders blow-by and therefore has deteriorating effect on the engine performance. Not much work has, hereto, been done to study the impact of altitude on the movement of the piston rings and hence the blow-by phenomenon. This papers presents a simulation model to investigate this effect.

Thermophysical Properties of Working Substance and Heat Transfer in a Hydrogen Combustion Engine

2003 ◽  
Author(s):  
T. Shudo ◽  
H. Oka
Keyword(s):  
Heat Transfer ◽  
Combustion Chamber ◽  
Heat Loss ◽  
Thermophysical Properties ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Spark Ignition ◽  
Hydrogen Combustion ◽  
Spark Ignition Engine ◽  
Combustion Engines

Hydrogen is a clean alternative to fossil fuels for internal combustion engines and can be easily used in spark-ignition engines. However, the characteristics of the engines fueled with hydrogen are largely different from those with conventional hydrocarbon fuels. A higher burning velocity and a shorter quenching distance for hydrogen as compared with hydrocarbons bring a higher degree of constant volume and a larger heat transfer from the burning gas to the combustion chamber wall of the engines. Because of the large heat loss, the thermal efficiency of an engine fueled with hydrogen is sometimes lower than that with hydrocarbons. Therefore, the analysis and the reduction of the heat loss are crucial for the efficient utilization of hydrogen in internal combustion engines. The empirical correlations to describe the total heat transferred from the burning gas to the combustion chamber walls are often used to calculate the heat loss in internal combustion engines. However, the previous research by one of the authors has shown that the widely used heat transfer correlations cannot be properly applied to the hydrogen combustion even with adjusting the constants in them. For this background, this research analyzes the relationship between characteristics of thermophysical properties of working substance and heat transfer to the wall in a spark-ignition engine fueled with hydrogen.

THE OXIDATION, DECOMPOSITION, IGNITION, AND DETONATION OF FUEL VAPORS AND GASES: XVI. BENZENE AS A KNOCKING FUEL IN CONDITIONS PROMOTING THE FORMATION OF FINELY DIVIDED CARBON

1950 ◽  
Vol 28f (8) ◽  
pp. 308-314
Author(s):  
R. O. King ◽  
E. J. Durand ◽  
A. B. Allan
Keyword(s):  
Low Temperature ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Otto Cycle ◽  
Liquid Drops ◽  
Air Supply

Experiments are described which demonstrate that benzene becomes a knocking fuel when used in a spark ignition Otto cycle engine if operating conditions are such that the vapor–air mixture becomes impregnated with finely divided carbon. The carbon was obtained on the impingement of the flame of burning benzene on relatively cool surfaces in the combustion chamber and by the burning of liquid drops dispersed in a combustible vapor–air mixture. The droplets were obtained by wet carburation even when the over-all mixture was weak; the engine being run with low temperature coolant, low temperature air supply, and with the carburetor attached directly to the engine head.

Investigation of engine performance for alcohol/kerosene blends as in spark-ignition aviation piston engine

2020 ◽  
Vol 268 ◽  
pp. 114959 ◽  
Author(s):  
Guibin Liu ◽  
Can Ruan ◽  
Zilong Li ◽  
Guan Huang ◽  
Qiyan Zhou ◽  
...  
Keyword(s):  
Engine Performance ◽  
Spark Ignition ◽  
Piston Engine

Lean-Burn Characteristics of a Heavy-Duty Diesel Engine Retrofitted to Natural-Gas Spark Ignition

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Jinlong Liu ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Combustion Chamber ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Fuel Injector ◽  
Heavy Duty ◽  
Lean Burn ◽  
Heavy Duty Diesel ◽  
Ci Engines

Increased utilization of natural gas (NG) in the transportation sector can decrease the use of petroleum-based fuels and reduced greenhouse gas emissions. Heavy-duty diesel engines retrofitted to NG spark ignition (SI) can achieve higher efficiencies and low NOX, CO, and hydrocarbon (HC) emissions when operated under lean-burn conditions. To investigate the SI lean-burn combustion phenomena in a bowl-in-piston combustion chamber, a conventional heavy-duty direct-injection CI engine was converted to SI operation by replacing the fuel injector with a spark plug and by fumigating NG in the intake manifold. Steady-state engine experiments and numerical simulations were performed at several operating conditions that changed spark timing (ST), engine speed, and mixture equivalence ratio. Results suggested a two-zone NG combustion inside the diesel-like combustion chamber. More frequent and significant late-burn (including double-peak heat release rate) was observed for advanced ST. This was due to the chamber geometry affecting the local flame speed, which resulted in a faster and thicker flame in the bowl but a slower and thinner flame in the squish volume. Good combustion stability (COVIMEP < 3%), moderate rate of pressure-rise, and lack of knocking showed promise for heavy-duty CI engines converted to NG SI operation.

Sign in / Sign up

Export Citation Format

Share Document