Sustainable Oil Adsorption from Produced Water using Cane Papyrus as Natural Biosorbent

2021 ◽  
Author(s):  
Mohammed Jaafar Ali Alatabe
Keyword(s):  
Produced Water ◽  
Fourier Transforms ◽  
Inorganic Compounds ◽  
Standard Free Energy ◽  
Isotherm Models ◽  
Standard Entropy ◽  
Order Kinetic ◽  
Standard Free Energy Change ◽  
First Order ◽  
Pseudo First Order

High quantities of wastewater produced from producing natural gas and oil from the aquifer, which called produced water. The produced water was comprised of dissolved solids, suspended solids, emulsified oil, and organic and inorganic compounds. That should be treated it's before disposal because it causes harm to the environment. This study takes the produced water from the southern Iraqi oilfield drilling company to adsorption by the Cane papyrus as natural and low-cost adsorbent. The analysis completed by using Fourier transforms infrared spectroscopy, EDX spectra and Scanning Electron Microscopic (SEM) for Cane papyrus. Investigating the effect of many parameters such as adsorbent dosage, temperature, solution pH, mixer speed and contact time. The Langmuir, Freundlich, Temkin and Harkins-Henderson isotherm models were tested, the results were 0.998,0.966, 0.931 and 0.966 respectively. The Langmuir model was more suitable described the adsorption process than the other models. The kinetics results were, 0.984 for Pseudo-first-order, 0.938 for Pseudo-second order is, 0.979 for Intra particle diffusion study and 0.912 for the Elovich model, the Pseudo-first-order kinetic equation best described the kinetics of the reaction. The thermodynamics study effect temperature changes on the thermodynamic parameters such as standard free energy change (∆G°), standard enthalpy change (∆H°) and standard entropy change (∆S°). The experimental data obtained demonstrated that Cane papyrus is a suitable adsorbent for removing oil from produced water.

scholarly journals Preparation and characterization of biodiesel waste-derived biomass for the removal of dye from contaminated water

2020 ◽  
Vol 69 (4) ◽  
pp. 365-375 ◽  
Author(s):  
Alagarasan Jagadeesh Kumar ◽  
Eldon R. Rene ◽  
Rajendra Prasad Singh ◽  
Shasikala Siddharthy ◽  
Jimin Xie ◽  
...  
Keyword(s):  
Ph Effect ◽  
Standard Free Energy ◽  
Contaminated Water ◽  
Standard Entropy ◽  
Order Kinetic ◽  
Batch Mode ◽  
First Order ◽  
Monolayer Adsorption ◽  
Order Kinetic Model ◽  
Pseudo First Order

Abstract Lignocellulosic biodiesel waste of Jatropha husk (JH) was used to develop ZnCl2 activated Jatropha husk carbon (ZAJHC). ZAJHC was applied as an adsorbent for the removal of methylene blue (MB) from contaminated water. Batch mode of adsorption experiments were carried out and the parameters investigated included agitation time, MB concentration (100–180 mg L−1) and adsorbent dose (25–200 mg/50 mL). The adsorption of MB reached equilibrium at 120 min for 100 mg L−1, 140 min for 120 mg L−1 and 160 min for other concentrations tested. Based on the Langmuir isotherm, the monolayer adsorption capacity (Q0) was found to be 500 mg g−1. The kinetic data were also fitted to the pseudo first-order, second-order and intraparticle diffusion models, and the experimental data followed closely the pseudo first-order kinetic model. Thermodynamic parameters such as standard enthalpy (ΔH° 3.86 J mol−1K−1), standard entropy (ΔS° 65.86 J mol−1K−1) and standard free energy (ΔG°) indicated the spontaneous nature of MB adsorption by ZAJHC. The adsorption was found to be endothermic in nature. Alkaline pH was favourable for the adsorption of MB. The pH effect and desorption studies suggest that ion-exchange might be the possible mechanism governing the adsorption process.

scholarly journals Indian Jujuba Seed Powder as an Eco-Friendly and a Low-Cost Biosorbent for Removal of Acid Blue 25 from Aqueous Solution

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
L. Sivarama Krishna ◽  
A. Sreenath Reddy ◽  
W. Y. Wan Zuhairi ◽  
M. R. Taha ◽  
A. Varada Reddy
Keyword(s):  
Aqueous Solution ◽  
Low Cost ◽  
Standard Free Energy ◽  
Isotherm Models ◽  
Standard Entropy ◽  
Standard Free Energy Change ◽  
Electron Microscopic ◽  
Enthalpy Changes ◽  
Acid Blue 25 ◽  
Acid Blue

Indian jujuba seed powder (IJSP) has been investigated as a low-cost and an eco-friendly biosorbent, prepared for the removal of Acid Blue 25 (AB25) from aqueous solution. The prepared biomaterial was characterized by using FTIR and scanning electron microscopic studies. The effect of operation variables, such as IJSP dosage, contact time, concentration, pH, and temperature on the removal of AB25 was investigated, using batch biosorption technique. Removal efficiency increased with increase of IJSP dosage but decreased with increase of temperature. The equilibrium data were analyzed by the Langmuir and the Freundlich isotherm models. The data fitted well with the Langmuir model with a maximum biosorption capacity of 54.95 mg g−1. The pseudo-second-order kinetics was the best for the biosorption of AB25 by IJSP, with good correlation. Thermodynamic parameters such as standard free energy change (ΔG0), standard enthalpy changes (ΔH0), and standard entropy changes (ΔS0) were analyzed. The removal of AB25 from aqueous solution by IJSP was a spontaneous and exothermic adsorption process. The results suggest that IJSP is a potential low-cost and an eco-friendly biosorbent for the AB25 removal from synthetic AB25 wastewater.

scholarly journals Adsorption of Acid Red 18 (AR18) by Activated Carbon from Poplar Wood- A Kinetic and Equilibrium Study

2010 ◽  
Vol 7 (1) ◽  
pp. 65-72 ◽  
Author(s):  
Reza Shokoohi ◽  
Vahid Vatanpoor ◽  
Mansuor Zarrabi ◽  
Akram Vatani
Keyword(s):  
Activated Carbon ◽  
Removal Efficiency ◽  
Kinetic Models ◽  
Contact Time ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Poplar Wood ◽  
Adsorbent Dosage ◽  
First Order ◽  
Pseudo First Order

Adsorption process by activated carbon is widely used for removal of dyes. Because of economical limits, activated carbon derived from low cost materials seem to be economical. The aim of this work is preparation of activated carbon from poplar wood and investigation of its ability to removal of (AR18) dye. In this work, we prepared the activated carbon by chemical activation method in electric furnace. In addition we have investigated effect of various parameters such as pH, contact time, dye concentration and adsorbent dosage on dye removal. Langmuir and Freundlich isotherm models have been investigated. Pseudo-first order, pseudo-second order and modified pseudo-first order kinetic models have been used for experimental data. The results showed that removal efficiency was increased with increasing of adsorbent dosage, contact time and decreasing of pH, but with increasing of dye concentration, the removal efficiency was decreased. Adsorption isotherm models showed that Langmuir isotherm model was best fitted onto collected data (r2>0.978). In addition, kinetic models showed that sorption of AR18 onto activated carbon prepared from poplar wood follows the pseudo-first order model (r2>0.9758).

scholarly journals Adsorption Behavior of Waste Leaves of Quercus Leucotrichophora for the Removal of Ni2+ and Cd2+ ions from Waste Water

2019 ◽  
Vol 35 (2) ◽  
pp. 591-596 ◽  
Author(s):  
Naveen Chandra Joshi ◽  
Vaishali Rangar ◽  
Ruchi Sati ◽  
Ekta Joshi ◽  
Ajay Singh
Keyword(s):  
Waste Water ◽  
Contact Time ◽  
Metal Ion ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Batch Experiments ◽  
First Order ◽  
Pseudo First Order ◽  
Quercus Leucotrichophora

Recently, the heavy metals are known for their toxicity to living organisms and natural environment. In the present study, we have removed Ni2+ and Cd2+ ions from synthetically prepared waste water under batch experiments using the waste leaves of Quercus leucotrichophora as low cost adsorbents. The adsorbent was characterized by FTIR and FESEM methods and the batch experiments included contact time, pH, dosage, temperature and concentration. The adsorption of metal ions was found maximum at the optimized conditions such as contact time 60 minutes, dosage 1 g, pH 5 and lower metal ion concentrations. The percentage adsorption at contact time 60 minutes, dosage 1 g and pH 6 was found 50.2, 51.0 and 74.0% for nickel and 38.8, 29.9 and 70.1% for cadmium. The adsorption data under selected batch system have been tested with Langmuir, Freundlich isotherm models, pseudo first order and pseudo second order kinetic models. Langmuir isotherm model and pseudo first order kinetic model were best fitted to adsorption of nickel and cadmium onto waste leaf powder of Quercus leucotrichophora.

scholarly journals Reuse of Brick Waste as a Cheap-Sorbent for the Removal of Nickel Ions from Aqueous Solutions

2020 ◽  
Vol 21 (2) ◽  
pp. 15-23
Author(s):  
Teba Hameed Mhawesh ◽  
Ziad T. Abd Ali
Keyword(s):  
Aqueous Solutions ◽  
Freundlich Isotherm ◽  
Bet Surface Area ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Sorption Data ◽  
Nickel Ions ◽  
X Ray ◽  
First Order ◽  
Pseudo First Order

   The potential application of granules of brick waste (GBW) as a low-cost sorbent for removal of Ni+2ions from aqueous solutions has been studied. The properties of GBW were determined through several tests such as X-Ray diffraction (XRD), Energy dispersive X-ray (EDX), Scanning electron microscopy (SEM), and BET surface area. In batch tests, the influence of several operating parameters including contact time, initial concentration, agitation speed, and the dose of GBW was investigated. The best values of these parameters that provided maximum removal efficiency of nickel (39.4%) were 1.5 hr, 50 mg/L, 250 rpm, and 1.8 g/100mL, respectively. The adsorption data obtained by batch experiments subjected to the Three isotherm models called Langmuir, Freundlich and Elovich, The results showed that the Freundlich isotherm model described well the sorption data (R2=0.9176) in comparison with other models. The kinetic data were analyzed using two kinetic models called pseudo-first-order and pseudo-second-order. The pseudo-first-order kinetic model was found to agree well with the experimental data.  

Leaching Kinetics of Atrazine and Inorganic Chemicals in Tilled and Orchard Soils

2014 ◽  
Vol 28 (2) ◽  
pp. 231-237 ◽  
Author(s):  
Lech W. Szajdak ◽  
Jerzy Lipiec ◽  
Anna Siczek ◽  
Artur Nosalewicz ◽  
Urszula Majewska
Keyword(s):  
Reaction Rate ◽  
Inorganic Compounds ◽  
Model Performance ◽  
Order Reaction ◽  
First Order Reaction ◽  
Order Kinetic ◽  
Time Data ◽  
First Order ◽  
Concentration Changes ◽  
Reaction Constants

Abstract The aim of this study was to verify first-order kinetic reaction rate model performance in predicting of leaching of atrazine and inorganic compounds (K+1, Fe+3, Mg+2, Mn+2, NH4 +, NO3 - and PO4 -3) from tilled and orchard silty loam soils. This model provided an excellent fit to the experimental concentration changes of the compounds vs. time data during leaching. Calculated values of the first-order reaction rate constants for the changes of all chemicals were from 3.8 to 19.0 times higher in orchard than in tilled soil. Higher first-order reaction constants for orchard than tilled soil correspond with both higher total porosity and contribution of biological pores in the former. The first order reaction constants for the leaching of chemical compounds enables prediction of the actual compound concentration and the interactions between compound and soil as affected by management system. The study demonstrates the effectiveness of simultaneous chemical and physical analyses as a tool for the understanding of leaching in variously managed soils.

scholarly journals Removal of organic pollutants from produced water by batch adsorption treatment

2021 ◽  
Author(s):  
Eman Hashim Khader ◽  
Thamer Jassim Mohammed ◽  
Nourollah Mirghaffari ◽  
Ali Dawood Salman ◽  
Tatjána Juzsakova ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Produced Water ◽  
Oxygen Demand ◽  
Powdered Activated Carbon ◽  
Pollutant Removal ◽  
Operating Conditions ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Zeolite X

AbstractThis paper studied the adsorption of chemical oxygen demand (COD), oil and turbidity of the produced water (PW) which accompanies the production and reconnaissance of oil after treating utilizing powdered activated carbon (PAC), clinoptilolite natural zeolite (CNZ) and synthetic zeolite type X (XSZ). Moreover, the paper deals with the comparison of pollutant removal over different adsorbents. Adsorption was executed in a batch adsorption system. The effects of adsorbent dosage, time, pH, oil concentration and temperature were studied in order to find the best operating conditions. The adsorption isotherm models of Langmuir, Freundlich and Temkin were investigated. Using pseudo-first-order and pseudo-second-order kinetic models, the kinetics of oil sorption and the shift in COD content on PAC and CNZ were investigated. At a PAC adsorbent dose of 0.25 g/100 mL, maximum oil removal efficiencies (99.57, 95.87 and 99.84 percent), COD and total petroleum hydrocarbon (TPH) were identified. Moreover, when zeolite X was used at a concentration of 0.25 g/100 mL, the highest turbidity removal efficiency (99.97%) was achieved. It is not dissimilar to what you would get with PAC (99.65 percent). In comparison with zeolites, the findings showed that adsorption over PAC is the most powerful method for removing organic contaminants from PW. In addition, recycling of the consumed adsorbents was carried out in this study to see whether the adsorbents could be reused. Chemical and thermal treatment will effectively regenerate and reuse powdered activated carbon and zeolites that have been eaten. Graphic abstract

scholarly journals Ganglioside incorporation and release by the isolated perfused rat liver

1991 ◽  
Vol 274 (2) ◽  
pp. 581-585 ◽  
Author(s):  
S C Kivatinitz ◽  
A Miglio ◽  
R Ghidoni
Keyword(s):  
Rat Liver ◽  
The Other ◽  
Regulatory Role ◽  
Isolated Perfused Rat Liver ◽  
Order Kinetic ◽  
Perfused Rat Liver ◽  
Ganglioside Gm1 ◽  
First Order ◽  
Pseudo First Order

The fate of exogenous ganglioside GM1 labelled in the sphingosine moiety, [Sph-3H]GM1, administered as a pulse, in the isolated perfused rat liver was investigated. When a non-recirculating protocol was employed, the amount of radioactivity in the liver and perfusates was found to be dependent on the presence of BSA in the perfusion liquid and on the time elapsed after the administration of the ganglioside. When BSA was added to the perfusion liquid, less radioactivity was found in the liver and more in the perfusate at each time tested, for up to 1 h. The recovery of radioactivity in the perfusates followed a complex course which can be described by three pseudo-first-order kinetic constants. The constants, in order of decreasing velocity, are interpreted as: (a) the dilution of the labelled GM1 by the constant influx of perfusion liquid; (b) the washing off of GM1 loosely bound to the surface of liver cells; (c) the release of gangliosides from the liver. Process (b) was found to be faster in the presence of BSA, probably owing to the ability of BSA to bind gangliosides. The [Sph-3H]GM1 in the liver underwent metabolism, leading to the appearance of products of anabolic (GD1a, GD1b) and catabolic (GM2, GM3) origin; GD1a appeared before GM2 and GM3 but, at times longer than 10 min, GM2 and GM3 showed more radioactivity than GD1a. At a given time the distribution of the radioactivity in the perfusates was quite different from that of the liver. In fact, after 60 min GD1a was the only metabolite present in any amount, the other being GM3, the quantity of which was small. This indicates that the liver is able to release newly synthesized gangliosides quite specifically. When a recirculating protocol was used, there were more catabolites and less GD1a than with the non-recirculating protocol. A possible regulatory role of ganglioside re-internalization on their own metabolism in the liver is postulated.

scholarly journals Enhanced photocatalytic activity of wool-ball-like TiO2 microspheres on carbon fabric and FTO substrates

2018 ◽  
Vol 38 ◽  
pp. 02014
Author(s):  
Yu Zhang ◽  
Jian Gu ◽  
Mengqi Zhang
Keyword(s):  
Hydrothermal Method ◽  
Order Kinetic ◽  
Carbon Fabric ◽  
Facile Hydrothermal Method ◽  
Sem Images ◽  
First Order ◽  
Good Crystallinity ◽  
Degradation Rate Constant ◽  
Order Kinetic Model ◽  
Pseudo First Order

The wool-ball-like TiO2 microspheres on carbon fabric (TiO2-CF) and FTO substrates (TiO2-FTO) have been synthesized by a facile hydrothermal method in alkali environment, using commercial TiO2 (P25) as precursors. The XRD results indicate that the as-prepared TiO2 have good crystallinity. And the SEM images show that the wool-ball-like TiO2 microspheres with a diameter of 2-3 μm are composed of TiO2 nanowires, which have a diameter of ~50 nm. The photocatalytic behavior of the wool-ball-like TiO2 microspheres, TiO2-CF and TiO2-FTO under ultraviolet light was investigated by a pseudo first-order kinetic model, using methyl orange (MO) as pollutant. The wool-ball-like TiO2 microspheres obtained a degradation rate constant (Kap) of 6.91×10-3 min-1 . The Kap values of TiO2-FTO and TiO2-CF reach 13.97×10-3 min-1 and 11.80×10-3 min-1, which are 2.0 and 1.7 times higher than that of pristine wool-ball-like TiO2 microspheres due to the “sum effect” between TiO2 and substrates. This study offers a facile hydrothermal method to prepare wool-ball-like TiO2 microspheres on CF and FTO substrates, which will improve the recyclability of phtocatalysts and can be extended to other fields.

scholarly journals Photocatalytic degradation of indigo carmine by ZnO photocatalyst under visible light irradiation

2017 ◽  
Vol 14 (3) ◽  
pp. 582-587
Author(s):  
Baghdad Science Journal
Keyword(s):  
Zinc Oxide ◽  
Photocatalytic Degradation ◽  
Indigo Carmine ◽  
Catalyst Loading ◽  
Order Kinetic ◽  
Kinetic Reaction ◽  
First Order ◽  
Pseudo First Order ◽  
The Relationship ◽  
Influential Parameters

In this work, the photocatalytic degradation of indigo carmine (IC) using zinc oxide suspension was studied. The effect of influential parameters such as initial indigo carmine concentration and catalyst loading were studied with the effect of Vis irradiation in the presence of reused ZnO was also investigated. The increased in initial dye concentration decreased the photodegradation and the increased catalyst loading increased the degradation percentage and the reused-ZnO exhibits lower photocatalytic activity than the ZnO catalyst. It has been found that the photocatalytic degradation of indigo carmine obeyed the pseudo-first-order kinetic reaction in presence of zinc oxide. This was found from plotting the relationship between ln (C0/Ct) and irradiation the rate constant of the process.UV- spectrophotometer was used to study the indigo carmine photodegradation.

Sign in / Sign up

Export Citation Format

Share Document