scholarly journals A preliminary approach to study the behavior of human fingertip at contact via experimental test and numerical model

ACTA IMEKO ◽  
2017 ◽  
Vol 6 (2) ◽  
pp. 81
Author(s):  
Maria Laura D'Angelo ◽  
Ferdinando Cannella ◽  
Mariapaola D'Imperio ◽  
Matteo Bianchi
Keyword(s):  
Experimental Data ◽  
Element Model ◽  
Fe Model ◽  
Proof Of Concept ◽  
Pressure Contour ◽  
Set Up ◽  
Deformation Models ◽  
Fundamental Action ◽  
Good Agreement

<p>How human fingertip deforms during the interaction with the environment represents a fundamental action that shapes our perception of external world. In this work, we present the <em>proof of concept</em> of an experimental <em>in vivo</em> set up that enables to characterize the mechanical behavior of human fingertip, in terms of contact area, force and a preliminary estimation of pressure contour, while it is put in contact against a flat rigid surface. Experimental outcomes are then compared with the output of a 3D Finite Element Model (FEM) of the human fingerpad, built upon existing validated models. The good agreement between numerical and experimental data suggests the correctness of our procedure for measurement acquisitions and finger modeling. Furthermore, we will also discuss how our experimental data can be profitably used to estimate strain limiting deformation models for tactile rendering, while the here reported 3D FE model has also been profitably employed to investigate hypotheses on human tactile perception.</p>

scholarly journals Fatigue Modeling and Numerical Analysis of Re-Filling Probe Hole of Friction Stir Spot Welded Joints in Aluminum Alloys

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2171
Author(s):  
Armin Yousefi ◽  
Ahmad Serjouei ◽  
Reza Hedayati ◽  
Mahdi Bodaghi
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Element Model ◽  
Plastic Strain Amplitude ◽  
Friction Stir ◽  
Probe Hole ◽  
Good Agreement

In the present study, the fatigue behavior and tensile strength of A6061-T4 aluminum alloy, joined by friction stir spot welding (FSSW), are numerically investigated. The 3D finite element model (FEM) is used to analyze the FSSW joint by means of Abaqus software. The tensile strength is determined for FSSW joints with both a probe hole and a refilled probe hole. In order to calculate the fatigue life of FSSW joints, the hysteresis loop is first determined, and then the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted. The results were verified against available experimental data from other literature, and a good agreement was observed between the FEM results and experimental data. The results showed that the joint’s tensile strength without a probe hole (refilled hole) is higher than the joint with a probe hole. Therefore, re-filling the probe hole is an effective method for structures jointed by FSSW subjected to a static load. The fatigue strength of the joint with a re-filled probe hole was nearly the same as the structure with a probe hole at low applied loads. Additionally, at a high applied load, the fatigue strength of joints with a refilled probe hole was slightly lower than the joint with a probe hole.

Finite Element Model of Human Cochlea Considering of the Helicotrema Size

2013 ◽  
Vol 456 ◽  
pp. 576-581 ◽  
Author(s):  
Li Fu Xu ◽  
Na Ta ◽  
Zhu Shi Rao ◽  
Jia Bin Tian
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Basilar Membrane ◽  
Round Window ◽  
Element Model ◽  
Oval Window ◽  
Fe Model ◽  
Cochlear Duct ◽  
Human Cochlea ◽  
Set Up

A 2-D finite element model of human cochlea is established in this paper. This model includes the structure of oval window, round window, basilar membrane and cochlear duct which is filled with fluid. The basilar membrane responses are calculated with sound input on the oval window membrane. In order to study the effects of helicotrema on basilar membrane response, three different helicotrema dimensions are set up in the FE model. A two-way fluid-structure interaction numerical method is used to compute the responses in the cochlea. The influence of the helicotrema is acquired and the frequency selectivity of the basilar membrane motion along the cochlear duct is predicted. These results agree with the experiments and indicate much better results are obtained with appropriate helicotrema size.

Conformational Structure of Chloromethyldichlorophosphines

2002 ◽  
Vol 57 (6-7) ◽  
pp. 333-336
Author(s):  
Evgenii A. Romanenko ◽  
Alexander M. Nesterenko
Keyword(s):  
Experimental Data ◽  
Ab Initio Calculations ◽  
Ab Initio ◽  
Electron Correlation ◽  
Basis Set ◽  
Conformational Structure ◽  
Gauche Conformation ◽  
Nuclear Quadrupole ◽  
Set Up ◽  
Good Agreement

IThe 35Cl nuclear quadrupole resonances (77 K) and ab initio calculations of trichloromethyldichlorophosphine () show that it exists in the chess conformation form. The barrier to internal rotation about the P-C bond in I at the RHF/6-31++ G(d,p) level equals to 38.1 kJ mol-1. In chloromethyldichlorophosphine (II) the extension of the basis set up to the RHF/6-311++G(df, pd) level does not improve the description of the most preferable gauche-conformation; only if electron correlation (at the MP2 level) is taken into account the results are in a good agreement with experimental data.

An assessment of the Sachs method for measuring residual stresses in cold worked fastener holes

1998 ◽  
Vol 33 (4) ◽  
pp. 263-274 ◽  
Author(s):  
D J Smith ◽  
C G C Poussard ◽  
M J Pavier
Keyword(s):  
Finite Element ◽  
Residual Stresses ◽  
Cold Working ◽  
Element Model ◽  
Fe Model ◽  
Working Process ◽  
Element Analysis ◽  
Near Surface ◽  
Cold Worked ◽  
Good Agreement

Measurements of residual stresses in 6 mm thick aluminium alloy 2024 plates containing 4 per cent cold worked fastener are made using the Sachs method. The measurements are made on discs extracted from the plates. The measured tangential residual stress distribution adjacent to the hole edge are found to be affected by the disc diameter. The measured residual stresses are also in good agreement with averaged through-thickness predictions of residual stresses from an axisymmetric finite element (FE) model of the cold working process. A finite element analysis is also conducted to simulate disc extraction and then the Sachs method. The measured FE residual stresses from the Sachs simulation are found to be in good agreement with the averaged through-thickness predicted residual stresses. The Sachs simulation was not able to reproduce the detailed near-surface residual stresses found from the finite element model of the cold working process.

A reaction-force-validated soccer ball finite element model

2016 ◽  
Vol 231 (1) ◽  
pp. 43-49 ◽  
Author(s):  
Zahari Taha ◽  
Mohd Hasnun Arif Hassan
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Finite Element Model ◽  
Reaction Force ◽  
Element Model ◽  
Optimal Number ◽  
Ball Impact ◽  
Soccer Ball ◽  
Mesh Density ◽  
Good Agreement

The soccer ball is one of the important pieces of equipment in the game of soccer. It undergoes various forms of impact during the game. In order to numerically investigate the occasions of ball impact such as soccer heading, a validated finite element model of a soccer ball is required. Therefore, a model was developed incorporating material properties obtained from literature. To ensure the accuracy of the model, it was validated against an established soccer ball model and experimental data of the coefficient of restitution, contact time, longitudinal deformation and reaction force. In addition, a parametric study of the mesh density was also performed to determine the optimal number of elements. The developed soccer ball model was found to be in a good agreement with the literature and experimental data. This suggests that, the soccer ball model is capable of replicating the impacts of interest. This article details the development of the model and the validation processes.

The use of electron gas modification in the evaluation of the vibration frequencies and the specific heat of lithium

1960 ◽  
Vol 259 (1298) ◽  
pp. 361-369 ◽  
Keyword(s):  
Experimental Data ◽  
Phase Transformation ◽  
Electron Gas ◽  
Vibration Frequencies ◽  
Specific Heats ◽  
Air Temperatures ◽  
Set Up ◽  
Good Agreement ◽  
Secular Determinant

A secular determinant for the determination of vibration frequencies of lithium has been set up by Launay’s method which takes the electron gas into account. Theoretical elastic constants have been used in the calculation of the force constants. Frequencies have been calculated for 47 points of the first Brillouin zone which gives the value of 3 x 1000 = 3000 frequencies by symmetry. Specific heats have been calculated by numerical computation in the range 300 to 6°K and show good agreement with the experimental data. The agreement below liquid-air temperatures is surprising in view of the known phase transformation of lithium.

Calculation of Fatigue Capacity for a Subsea Wellhead Connector

2020 ◽  
Author(s):  
Seyed H. Hashemizadeh ◽  
Venu Sunkavilli ◽  
Torfinn Hørte ◽  
Per Osen
Keyword(s):  
Fatigue Life ◽  
Hot Spot ◽  
High Strength Steels ◽  
Steel Structures ◽  
High Strength ◽  
Element Model ◽  
Fe Model ◽  
Specific Advice ◽  
Drilling Operations ◽  
Set Up

Abstract In the 2019 version of DNVGL-RP-C203 Fatigue Design of Offshore Steel Structures, significantly improved methods have been added on how to establish M-N curves representing the fatigue resistance of preloaded connectors subject to cyclic bending. The M-N curve parameters are typically provided by the manufacturer and used by operators and drilling contractors for calculating the wellhead fatigue life for planned drilling operations. DNVGL-RP-C203 provides specific advice on how to establish design M-N curves based on analysis, and the augmentation by possible testing, where testing may grant more favorable M-N curves and thus extended fatigue life for any given case. The paper provides background and introduction to the improved analysis methodology and relevant S-N curves for high-strength steels for wellhead systems, given in the 2019 version of the DNVGL-RP-C203. It includes a worked example in order to demonstrate the detailed use of the method, applied on a Baker Hughes preloaded BOP connector, connected to a 27” wellhead mandrel. This example describes the finite element model set up, FE model mesh refinement in hot-spots, the application of cyclic loads, extraction of hot-spot cyclic stresses, and the establishment of the M-N curve for the connector.

Numerical and Experimental Analysis of Articular Chondrocyte Deformation: Calibration of a Multiscale Finite Element Model

2007 ◽  
Author(s):  
Scott L. Bevill ◽  
Paul L. Briant ◽  
Thomas P. Andriacchi
Keyword(s):  
Finite Element ◽  
Load Transfer ◽  
Numerical Models ◽  
Experimental Studies ◽  
Element Model ◽  
Cartilage Explants ◽  
Fe Model ◽  
Articular Chondrocyte ◽  
Superficial Zone

Mechanical loading of chondrocytes in isolation [1] and of articular cartilage in culture [2] has been reported to be a potent regulator of chondrocyte metabolism. Experimental studies have related tissue-level and cell-level strains in mechanically loaded cartilage explants [3], but cannot be readily extended to address more physiologic loading cases. Numerical models, which might address this need, have primarily been axisymmetric [4, 5] or two-dimensional [6] and have idealized chondrocyte geometry. Given the complexity of the mechanism of the load transfer between the tissue and cell, however, there remains a lack of information regarding the in vivo level of cell stresses and strains. Thus, the purpose of this study was to develop a multiscale experimental/numerical approach to calibrate a three-dimensional finite element (FE) model of a chondrocyte based on experimentally derived chondrocyte morphology and deformation data. The method was than applied to determine the modulus of a chondrocyte located in the superficial zone.

Damping Matrix Identification by Finite Element Model Updating Using Frequency Response Data

2017 ◽  
Vol 17 (01) ◽  
pp. 1750004 ◽  
Author(s):  
S. Pradhan ◽  
S. V. Modak
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Frequency Response ◽  
Model Updating ◽  
Experimental Studies ◽  
Element Model ◽  
Fe Model ◽  
Damping Matrix ◽  
Steel Cast ◽  
Identification Techniques

Accurate modeling of damping is essential for prediction of vibration response of a structure. This paper presents a study of damping matrix identification method using experimental data. The identification is done by performing finite element (FE) model updating using normal frequency response functions (FRFs). The paper addresses some key issues like data incompleteness and computation of the normal FRFs for carrying out the model updating using experimental data. The effect of various levels of damping in structures on the performance of the identification techniques is also investigated. Experimental studies on three beam structures made up of mild steel, cast iron and acrylic are presented to demonstrate the effectiveness of the identification techniques for different levels of damping.

Compressive Behavior of AA6061 at Room Temperature and Validation of the FE Model Based on Optical 3D Measurement Technique

2013 ◽  
Vol 594-595 ◽  
pp. 909-913
Author(s):  
A.B. Abdullah ◽  
Z. Samad
Keyword(s):  
Finite Element ◽  
Measurement Technique ◽  
Room Temperature ◽  
Element Model ◽  
Surface Measurement ◽  
Fe Model ◽  
Cold Upsetting ◽  
Element Simulation ◽  
The Finite Element Model ◽  
Good Agreement

Recently, manufacturing process simulation using finite element (FE) model become important. Therefore, validation of the finite element model is crucial. This study will present validation of 2D finite element simulation of cold heading at room temperature. Validation of the simulation model is carried out by comparing the resulted bulge profile of the cold upsetting specimen to the profile of the specimen, which is obtained from an optical 3D surface measurement technique namely Infinite Focus Alicona system. Based on the result, both profiles show a very good agreement.

Sign in / Sign up

Export Citation Format

Share Document