scholarly journals Seepage Characteristics of a Low Permeability Sandstone Reservoir in Mobei Oilfield, Junggar Basin

Lithosphere ◽  
2021 ◽  
Vol 2021 (Special 4) ◽  
Author(s):  
Qi Lisha ◽  
Jiang Zhibin ◽  
Wang Xiaowei ◽  
Wang Jie ◽  
Qian Chuanchuan

Abstract The microscopic pore structure characteristics and the oil-water two-phase seepage law in the low permeability sandstone reservoir in Mobei oilfield in Junggar Basin were analyzed through laboratory experiments. The results of mercury pressure, constant velocity mercury pressure, thin slice of casting, and CT scan analyses showed that the reservoir had strong microheterogeneity with the presence of local large channels. The large channel had a small volume but considerably contributed to the permeability, which played a crucial role in the reservoir seepage. The relative permeability curve showed that with the increase of water saturation, the relative permeability of the oil phase decreased rapidly; the water phase relative permeability of glutenite, gravel-bearing sandstone, and coarse sandstone increased slightly; and the water cut increased rapidly. The relative permeability of the water phase of medium and fine sandstone increased, the water cut increased rapidly, and the residual oil saturation was high. In the process of core displacement, on-line CT scanning monitoring showed that before the breakthrough of the water drive front, the oil saturation decreased greatly along the way. After the breakthrough of the water drive front, the water cut increased rapidly and directly entered the ultrahigh water cut stage. Owing to the serious heterogeneity of the micropore structure, the fingering phenomenon was obvious in the process of displacement.

2014 ◽  
Vol 1010-1012 ◽  
pp. 1676-1683 ◽  
Author(s):  
Bin Li ◽  
Wan Fen Pu ◽  
Ke Xing Li ◽  
Hu Jia ◽  
Ke Yu Wang ◽  
...  

To improve the understanding of the influence of effective permeability, reservoir temperature and oil-water viscosity on relative permeability and oil recovery factor, core displacement experiments had been performed under several experimental conditions. Core samples used in every test were natural cores that came from Halfaya oilfield while formation fluids were simulated oil and water prepared based on analyze data of actual oil and productive water. Results from the experiments indicated that the shape of relative permeability curves, irreducible water saturation, residual oil saturation, width of two-phase region and position of isotonic point were all affected by these factors. Besides, oil recovery and water cut were also related closely to permeability, temperature and viscosity ratio.


2017 ◽  
pp. 77-83
Author(s):  
V. A. Korotenko ◽  
S. I. Grachev ◽  
N. P. Kushakova

The article discusses the differential equation of the stationary two-phase filtration, the obtained as a spe-cial case of nonlinear non-stationary equations. It is established that for the formulation of solutions it is necessary to use the dependence of water-saturation and oil-saturation factors on the pressure of water pumped into the reservoir. With the advance bringing into the development of the injection well, it has been established, that the water and oil flow rates and the water-cut coefficient depend on the selected coefficients of the relative permeability and the outer boundary of the drainage area. The merits and demerits of the stationary filtration model are estimated.


1985 ◽  
Vol 25 (06) ◽  
pp. 945-953 ◽  
Author(s):  
Mark A. Miller ◽  
H.J. Ramey

Abstract Over the past 20 years, a number of studies have reported temperature effects on two-phase relative permeabilities in porous media. Some of the reported results, however, have been contradictory. Also, observed effects have not been explained in terms of fundamental properties known to govern two-phase flow. The purpose of this study was to attempt to isolate the fundamental properties affecting two-phase relative permeabilities at elevated temperatures. Laboratory dynamic-displacement relative permeability measurements were made on unconsolidated and consolidated sand cores with water and a refined white mineral oil. Experiments were run on 2-in. [5.1-cm] -diameter, 20-in. [52.-cm] -long cores from room temperature to 300F [149C]. Unlike previous researchers, we observed essentially no changes with temperature in either residual saturations or relative permeability relationships. We concluded that previous results may have been affected by viscous previous results may have been affected by viscous instabilities, capillary end effects, and/or difficulties in maintaining material balances. Introduction Interest in measuring relative permeabilities at elevated temperatures began in the 1960's with petroleum industry interest in thermal oil recovery. Early thermal oil recovery field operations (well heaters, steam injection, in-situ combustion) indicated oil flow rate increases far in excess of what was predicted by viscosity reductions resulting from heating. This suggested that temperature affects relative permeabilities. One of the early studies of temperature effects on relative permeabilities was presented by Edmondson, who performed dynamic displacement measurements with crude performed dynamic displacement measurements with crude and white oils and distilled water in Berea sandstone cores. Edmondson reported that residual oil saturations (ROS's) (at the end of 10 PV's of water injected) decreased with increasing temperature. Relative permeability ratios decreased with temperature at high water saturations but increased with temperature at low water saturations. A series of elevated-temperature, dynamic-displacement relative permeability measurements on clean quartz and "natural" unconsolidated sands were reported by Poston et al. Like Edmondson, Poston et al. reported a decrease in the "practical" ROS (at less than 1 % oil cut) as temperature increased. Poston et al. also reported an increase in irreducible water saturation. Although irreducible water saturations decreased with decreasing temperature, they did not revert to the original room temperature values. It was assumed that the cores became increasingly water-wet with an increase in both temperature and time; measured changes of the IFT and the contact angle with temperature increase, however, were not sufficient to explain observed effects. Davidson measured dynamic-displacement relative permeability ratios on a coarse sand and gravel core with permeability ratios on a coarse sand and gravel core with white oil displaced by distilled water, nitrogen, and superheated steam at temperatures up to 540F [282C]. Starting from irreducible water saturation, relative permeability ratio curves were similar to Edmondson's. permeability ratio curves were similar to Edmondson's. Starting from 100% oil saturation, however, the curves changed significantly only at low water saturations. A troublesome aspect of Davidson's work was that he used a hydrocarbon solvent to clean the core between experiments. No mention was made of any consideration of wettability changes, which could explain large increases in irreducible water saturations observed in some runs. Sinnokrot et al. followed Poston et al.'s suggestion of increasing water-wetness and performed water/oil capillary pressure measurements on consolidated sandstone and limestone cores from room temperature up to 325F [163C]. Sinnokrot et al confirmed that, for sandstones, irreducible water saturation appeared to increase with temperature. Capillary pressures increased with temperature, and the hysteresis between drainage and imbibition curves reduced to essentially zero at 300F [149C]. With limestone cores, however, irreducible water saturations remained constant with increase in temperature, as did capillary pressure curves. Weinbrandt et al. performed dynamic displacement experiments on small (0.24 to 0.49 cu in. [4 to 8 cm3] PV) consolidated Boise sandstone cores to 175F [75C] PV) consolidated Boise sandstone cores to 175F [75C] with distilled water and white oil. Oil relative permeabilities shifted toward high water saturations with permeabilities shifted toward high water saturations with increasing temperature, while water relative permeabilities exhibited little change. Weinbrandt et al. confirmed the findings of previous studies that irreducible water saturation increases and ROS decreases with increasing temperature. SPEJ P. 945


1996 ◽  
Vol 464 ◽  
Author(s):  
E. H. Kawamoto ◽  
Po-Zen Wong

ABSTRACTWe have carried out x-ray radiography and computed tomography (CT) to study two-phase flow in 3-D porous media. Air-brine displacement was imaged for drainage and imbibition experiments in a vertical column of glass beads. By correlating water saturation Sw with resistance R, we find that there is a threshold saturation S* ≈ 0.2, above which R(SW) ∼ Sw−2, in agreement with the empirical Archie relation. This holds true for both drainage and imbibition with littlehysteresis, provided that Sw remains above S*. Should Sw drop below S* during drainage, R(Sw) rises above the Archie prediction, exhibiting strong hysteresis upon reimbibition. This behavior suggests a transition in the connectivity of the water phase near S*, possibly due to percolation effects.


1964 ◽  
Vol 4 (01) ◽  
pp. 49-55 ◽  
Author(s):  
Pietro Raimondi ◽  
Michael A. Torcaso

Abstract The distribution of the oil phase in Berea sandstone resulting from increasing and decreasing the water saturation by imbibition was investigated Three types of distribution were recognized: trapped, normal and lagging. The amount of oil in each of these distributions was determined as a function of saturation by carrying out a miscible displacement in the oil phase under steady-state conditions of saturation. These conditions were maintained by flowing water and oil simultaneously in given ratios and by using a displacing solvent having essentially the same density and viscosity as the oil.A correlation shows the amount of trapped oil at any saturation to be directly proportional to the conventional residual oil saturation Sir The factor of proportionality is related to the fractional permeability to the water phase. Part of the oil which was not trapped was displaced in a piston- like manner (normal part) and part was eluted gradually (lagging part). The observed phenomena are more than of mere academic importance. Oil which is trapped may well provide the fuel essential for forward combustion and thus be beneficial. On the contrary, in tertiary recovery operations, it is this trapped oil which seems to make current techniques uneconomic. Introduction A typical oilfield may initially contain connate water and oil. After a period of primary production water often enters the field either from surrounding aquifers or from surface injection. During primary production evolution and establishment of a free gas saturation usually occurs. The effect and importance of this third phase is fully recognized. However, this investigation is limited to a two- phase system, one wetting phase (water) and one non-wetting phase (oil). The increase in water content of a water-wet system is termed imbibition. In a relative permeability-saturation diagram such as the one shown in Fig. 1, the initial conditions of the field would he represented by a point below a water saturation of about 35 per cent, i.e., where the imbibition and the drainage curves to the non-wetting phase nearly coincide. When water enters the field the relative permeability to oil decreases along the imbibition curve. At watered-out conditions the relative permeability to the oil becomes zero. At this point a considerable amount of oil, called residual oil, (about 35 per cent in Fig. 1) remains unrecovered. Any attempt to produce this oil will require that its saturation be increased. In Fig. 1 this would mean retracing the imbibition curve upwards. In addition, processes like alcohol and fire flooding, which can be employed at any stage of production, involve the complete displacement of connate water and an increase, or imbibition, of water saturation ahead of the displacing front. Thus, in several types of oil production it is the imbibition-relative permeability curve which rules the flow behavior. For this reason a knowledge of the distribution of the non-wetting phase, as obtained through imbibition, whether "coming down" or "going up" on the imbibition curve, is important. SPEJ P. 49^


2020 ◽  
Vol 10 (8) ◽  
pp. 3649-3661
Author(s):  
Meiling Zhang ◽  
Jiayi Fan ◽  
Yongchao Zhang ◽  
Yinxin Liu

Abstract The water cutting rate is recorded dynamically during the production process of a well. If the remaining oil saturation of the reservoir can be deduced based on the water cutting rate, it will give guidance to improve the reservoir recovery and can save expensive drilling costs. In the oil–water two-phase seepage experiment on core samples, the oil and water relative permeability reflects the relationship between the water cutting rate and water saturation, that is, percolating saturation formula. The relative permeability test data of 17 rock samples from six seal coring wells in Daqing Changyuan were used to optimize and construct the coefficients of the index percolating saturation formula that vary with the pore structure parameters of reservoirs, to form an index percolating saturation formula with variable coefficients that is more consistent with the regional geological characteristics of the reservoir. Based on this, the formula of water saturation calculated by the water cutting rate is deduced. And the high-precision formula for calculating the irreducible water saturation and residual oil saturation by effective porosity, absolute permeability, and shale content is given. The derivative formula of water saturation on the water cutting rate was established, and the parameters of 17 rock samples were calculated. It was found that the variation velocity of water saturation of each sample with the water cutting rate presented a “U” shape, which was consistent with the actual characteristics that the variation velocity of the water saturation in the early, middle, and late stages of oilfield development first decreased, then stabilized, and finally increased rapidly. The research results were applied to the prediction of remaining oil saturation in the research area, and the water saturation about six producing wells was calculated by using their present water cutting rates, and the remaining oil distribution profile was predicted effectively. The analysis of four layers of two newly drilled infill wells and reasonable oil recovery suggestions were given to achieve good results.


SPE Journal ◽  
2020 ◽  
Vol 25 (06) ◽  
pp. 3265-3279
Author(s):  
Hamidreza Hamdi ◽  
Hamid Behmanesh ◽  
Christopher R. Clarkson

Summary Rate-transient analysis (RTA) is a useful reservoir/hydraulic fracture characterization method that can be applied to multifractured horizontal wells (MFHWs) producing from low-permeability (tight) and shale reservoirs. In this paper, we applied a recently developed three-phase RTA technique to the analysis of production data from an MFHW completed in a low-permeability volatile oil reservoir in the Western Canadian Sedimentary Basin. This RTA technique is used to analyze the transient linear flow regime for wells operated under constant flowing bottomhole pressure (BHP) conditions. With this method, the slope of the square-root-of-time plot applied to any of the producing phases can be used to directly calculate the linear flow parameter xfk without defining pseudovariables. The method requires a set of input pressure/volume/temperature (PVT) data and an estimate of two-phase relative permeability curves. For the field case studied herein, the PVT model is constructed by tuning an equation of state (EOS) from a set of PVT experiments, while the relative permeability curves are estimated from numerical model history-matchingresults. The subject well, an MFHW completed in 15 stages, produces oil, water, and gas at a nearly constant (measured downhole) flowing BHP. This well is completed in a low-permeability,near-critical volatile oil system. For this field case, application of the recently proposed RTA method leads to an estimate of xfk that is in close agreement (within 7%) with the results of a numerical model history match performed in parallel. The RTA method also provides pressure–saturation (P–S) relationships for all three phases that are within 2% of those derived from the numerical model. The derived P–S relationships are central to the use of other RTA methods that require calculation of multiphase pseudovariables. The three-phase RTA technique developed herein is a simple-yet-rigorous and accurate alternative to numerical model history matching for estimating xfk when fluid properties and relative permeability data are available.


2020 ◽  
Vol 146 ◽  
pp. 05001
Author(s):  
Denis Dzhafarov ◽  
Benjamin Nicot

Relative permeability is a concept used to convey the reduction in flow capability due to the presence of multiple fluids. Relative permeability governs the multiphase flow, therefore it has a significant importance in understanding the reservoir behavior. These parameters are routinely measured on conventional rocks, however their measurement becomes quite challenging for low permeability rocks such as tight gas formations. This study demonstrates a methodology for relative permeability measurements on tight gas samples. The gas permeability has been measured by the Step Decay method and two different techniques have been used to vary the saturations: steady state flooding and vapor desorption. Series of steady-state gas/water simultaneous injection have been performed on a tight gas sample. After stabilization at each injection ratio, NMR T2, NMR Saturation profile and low pressure Step Decay gas permeability have been measured. In parallel, progressive desaturation by vapor desorption technique has been performed on twin plugs. After stabilization at each relative humidity level the NMR T2 and Step Decay gas permeability have been measured in order to compare and validate the two approaches. The techniques were used to gain insight into the tight gas two phase relative permeability of extremely low petrophysical properties (K<100 nD, phi < 5 pu) of tight gas samples of Pyrophyllite outcrop. The two methods show quite good agreement. Both methods demonstrate significant permeability degradation at water saturation higher than irreducible. NMR T2 measurements for both methods indicates bimodal T2-distributions, and desaturation first occurs on low T2 signal (small pores). Comparison of humidity drying and steady-state desaturation technique has shown a 12-18 su difference between critical water saturation (Swc) measured in gas/water steady-state injection and irreducible saturation (Swirr) measured by vapor desorption.


2020 ◽  
pp. 69-81
Author(s):  
I. M. Sagitova ◽  
D. K. Sagitov ◽  
Yu. V. Zeigman

The development of undersaturated oil layered heterogeneous oil reservoirs against the background of a general depletion of oil reserves is becoming increasingly interesting. The development of these hard-to-recover oil reserves is associated with non-standard changes and increased water-cut in wells. An undersaturated (unformed, young) reservoir is a conditionally large transitional water-oil zone of the reservoir, in its classical sense. It is assumed that, since the initial oil saturation of the formation is low, and the water saturation is correspondingly high, the starting water cut should correspond to this ratio, but this is not so in some cases. At the same time, it is difficult to say in advance whether water-cut will increase, stabilize or fall in the first months. The study is aimed at identifying the determining parameter and the ranges of its change by statistical methods, based on which it will be possible to predict with high probability the nature of the change in water cut during the feasibility study for drilling new wells. For the conditions of the selected object, a graphical dependence of the water cut deviation in the initial period of well operation from layered heterogeneity of the reservoir is found. The results of the study are the rationale for creating new technologies for the selective isolation of oil-layers. It should to allow reversibly limiting the permeability of the low-permeability low-saturated part of the reservoir. Most of the existing technologies are aimed at the selective isolation of high-permeability and watered layers.


2014 ◽  
Vol 522-524 ◽  
pp. 1562-1566
Author(s):  
Li Ping He ◽  
Ping Ping Shen ◽  
Qi Chao Gao ◽  
Meng Chen ◽  
Xiang Yang Ma

Because of the instability of steam and tough requirement of HTHP equipments in steam flooding laboratory simulation, it is rather difficult to obtain representative Steam/Oil relative permeability curves with high precision. In addition, although the effect of temperature on Water/Oil relative permeability curves has been studied a lot both at home and aboard, there are still some controversy perspectives, and research on temperature effect on Steam/Oil relative permeability is rare. As to the above issue, an improved steam flooding experimental method is launched to obtain accurate base data, and then simplified JBN method is applied for data processing. The Result revealed that the improved experimental methods and simplified JBN formulas can obtain representative Steam/Oil relative permeability with high precision, and temperature affects steam/oil relative permeability in various aspects, as temperature increased, oil relative permeability and irreducible water saturation increased while steam relative permeability and residual oil saturation decreased.


Sign in / Sign up

Export Citation Format

Share Document