An Experimental Investigation of Gas-Production Rates During Depressurization of Sedimentary Methane Hydrates

SPE Journal ◽  
2019 ◽  
Vol 24 (02) ◽  
pp. 522-530 ◽  
Author(s):  
Stian Almenningen ◽  
Per Fotland ◽  
Martin A. Fernø ◽  
Geir Ersland
Keyword(s):  
Gas Production ◽  
Production Performance ◽  
Methane Hydrates ◽  
Gas Recovery ◽  
Rate Analysis ◽  
Pressure Depletion ◽  
Hydrate Saturation ◽  
Rate Of Recovery ◽  
Magnetic Resonance Imaging Mri ◽  
Production Rate Analysis

Summary Sedimentary methane hydrates contain a vast amount of untapped natural gas that can be produced through pressure depletion. Several field pilots have proved the concept with days to weeks of operation, but the longer-term response remains uncertain. This paper investigates the parameters affecting the rate of gas recovery from methane-hydrate-bearing sediments. The recovery of methane gas from hydrate dissociation through pressure depletion was studied at different initial hydrate saturations and different constant production pressures in cylindrical sandstone cores. Core-scale dissociation patterns were mapped with magnetic resonance imaging (MRI), and pore-scale dissociation events were visualized in a high-pressure micromodel. Key findings from the gas-production-rate analysis are that the maximum rate of recovery is only to a small extent affected by the magnitude of the pressure reduction below the dissociation pressure, and that the hydrate saturation directly affects the rate of recovery, where intermediate hydrate saturations (0.30 to 0.50) give the highest initial recovery rate. These results are of interest to anyone who evaluates the production performance of sedimentary hydrate accumulations and demonstrate how important accurate saturation estimates are to prediction of both the initial rate of gas recovery and the ultimate-recovery efficiency.

Impact of the Cluster Spacing on Hydraulic Fracture Conductivity and Productivity of a Marcellus Shale Horizontal Well

2021 ◽  
Author(s):  
Mohamed El Sgher ◽  
Kashy Aminian ◽  
Ameri Samuel
Keyword(s):  
Hydraulic Fracture ◽  
Marcellus Shale ◽  
Technical Information ◽  
Gas Production ◽  
Production Performance ◽  
Valuable Insight ◽  
Fracture Conductivity ◽  
Fracture Properties ◽  
Gas Recovery ◽  
The Impact

Abstract The objective of this study was to investigate the impact of the hydraulic fracturing treatment design, including cluster spacing and fracturing fluid volume on the hydraulic fracture properties and consequently, the productivity of a horizontal Marcellus Shale well with multi-stage fractures. The availability of a significant amount of advanced technical information from the Marcellus Shale Energy and Environment Laboratory (MSEEL) provided an opportunity to perform an integrated analysis to gain valuable insight into optimizing fracturing treatment and the gas recovery from Marcellus shale. The available technical information from a horizontal well at MSEEL includes well logs, image logs (both vertical and lateral), diagnostic fracture injection test (DFIT), fracturing treatment data, microseismic recording during the fracturing treatment, production logging data, and production data. The analysis of core data, image logs, and DFIT provided the necessary data for accurate prediction of the hydraulic fracture properties and confirmed the presence and distribution of natural fractures (fissures) in the formation. Furthermore, the results of the microseismic interpretation were utilized to adjust the stress conditions in the adjacent layers. The predicted hydraulic fracture properties were then imported into a reservoir simulation model, developed based on the Marcellus Shale properties, to predict the production performance of the well. Marcellus Shale properties, including porosity, permeability, adsorption characteristics, were obtained from the measurements on the core plugs and the well log data. The Quanta Geo borehole image log from the lateral section of the well was utilized to estimate the fissure distribution s in the shale. The measured and published data were utilized to develop the geomechnical factors to account for the hydraulic fracture conductivity and the formation (matrix and fissure) permeability impairments caused by the reservoir pressure depletion during the production. Stress shadowing and the geomechanical factors were found to play major roles in production performance. Their inclusion in the reservoir model provided a close agreement with the actual production performance of the well. The impact of stress shadowing is significant for Marcellus shale because of the low in-situ stress contrast between the pay zone and the adjacent zones. Stress shadowing appears to have a significant impact on hydraulic fracture properties and as result on the production during the early stages. The geomechanical factors, caused by the net stress changes have a more significant impact on the production during later stages. The cumulative gas production was found to increase as the cluster spacing was decreased (larger number of clusters). At the same time, the stress shadowing caused by the closer cluster spacing resulted in a lower fracture conductivity which in turn diminished the increase in gas production. However, the total fracture volume has more of an impact than the fracture conductivity on gas recovery. The analysis provided valuable insight for optimizing the cluster spacing and the gas recovery from Marcellus shale.

scholarly journals Effect of Perforation Interval Design on Gas Production from the Validated Hydrate-Bearing Deposits with Layered Heterogeneity by Depressurization

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-20
Author(s):  
Yingli Xia ◽  
Tianfu Xu ◽  
Yilong Yuan ◽  
Xin Xin
Keyword(s):  
Energy Demand ◽  
Production Efficiency ◽  
Gas Production ◽  
Production Performance ◽  
Gas Release ◽  
Methane Recovery ◽  
Hydrate Dissociation ◽  
Gas Recovery ◽  
Hydrate Reservoir ◽  
Production Wells

Natural gas hydrate is considered as one of the best potential alternative resource to address the world’s energy demand. The available geological data at the Mallik site of Canada indicates the vertical heterogeneities of hydrate reservoir petrophysical properties. According to the logging data and sample analysis results at the Mallik 2L-38 well, a 2D model of geologically descriptive hydrate-bearing sediments was established to investigate the multiphase flow behaviors in hydrate reservoir induced by gas recovery and the effects of perforation interval on gas production performance. Firstly, the constructed model with vertical heterogeneous structures of permeability, porosity, and hydrate saturation was validated by matching the measured data in the Mallik 2007 test. The excessive residual methane in the hydrate reservoir observed in simulated results indicates insufficient gas production efficiency. For more effective methane recovery from a hydrate reservoir, the effect of perforation interval on long-term gas production performance was investigated based on the validated reservoir model. The simulation results suggest that both the location and length of the perforation interval have significant impact on hydrate dissociation behavior, while the gas production performance is mainly affected by the length of the perforation interval. To be specific, an excellent gas release performance is found in situations where the perforation interval is set at the interface between a hydrate reservoir and an underlying water-saturated zone. By increasing the perforation interval lengths of 5 m, 8 m, and 10 m, the gas release volumes from hydrate dissociation and gas production volumes from production wells are increased by 34%, 52%, and 57% and 37%, 58%, and 62%, respectively.

scholarly journals Multiphase Flow Behavior of Layered Methane Hydrate Reservoir Induced by Gas Production

Geofluids ◽  
2017 ◽  
Vol 2017 ◽  
pp. 1-15 ◽  
Author(s):  
Yilong Yuan ◽  
Tianfu Xu ◽  
Xin Xin ◽  
Yingli Xia
Keyword(s):  
Multiphase Flow ◽  
Gas Hydrate ◽  
Methane Hydrate ◽  
Nankai Trough ◽  
Flow Behavior ◽  
Gas Production ◽  
Production Performance ◽  
Heterogeneous Structure ◽  
Hydrate Saturation ◽  
Hydrate Reservoirs

Gas hydrates are expected to be a potential energy resource with extensive distribution in the permafrost and in deep ocean sediments. The marine gas hydrate drilling explorations at the Eastern Nankai Trough of Japan revealed the variable distribution of hydrate deposits. Gas hydrate reservoirs are composed of alternating beds of sand and clay, with various conditions of permeability, porosity, and hydrate saturation. This study looks into the multiphase flow behaviors of layered methane hydrate reservoirs induced by gas production. Firstly, a history matching model by incorporating the available geological data at the test site of the Eastern Nankai Trough, which considers the layered heterogeneous structure of hydrate saturation, permeability, and porosity simultaneously, was constructed to investigate the production characteristics from layered hydrate reservoirs. Based on the validated model, the effects of the placement of production interval on production performance were investigated. The modeling results indicate that the dissociation zone is strongly affected by the vertical reservoir’s heterogeneous structure and shows a unique dissociation front. The beneficial production interval scheme should consider the reservoir conditions with high permeability and high hydrate saturation. Consequently, the identification of the favorable hydrate deposits is significantly important to realize commercial production in the future.

Geomechanical Response Induced by Multiphase (Gas/Water) Flow in the Mallik Hydrate Reservoir of Canada

SPE Journal ◽  
2021 ◽  
pp. 1-18
Author(s):  
Yingli Xia ◽  
Tianfu Xu ◽  
Yilong Yuan ◽  
Xin Xin ◽  
Huixing Zhu
Keyword(s):  
Shear Stress ◽  
Shear Failure ◽  
Energy Resource ◽  
Gas Production ◽  
Production Performance ◽  
Reservoir Model ◽  
Hydrate Reservoir ◽  
Maximum Subsidence ◽  
Permeability Anisotropy

Summary Natural gas hydrate (NGH) is regarded as an important alternative future energy resource. In recent years, a few short-term production tests have been successfully conducted with both permafrost and marine sediments. However, long-term hydrate production performance and the potential geomechanical problems are not very clear. According to the available geological data at the Mallik site, a more realistic hydrate reservoir model that considers the heterogeneity of porosity, permeability, and hydrate saturation was developed and validated by reproducing the field depressurization test. The coupled multiphase and heat flow and geomechanical response induced by depressurization were fully investigated for long-term gas production from the validated hydrate reservoir model. The results indicate that long-term gas production through depressurization from a vertically heterogeneous hydrate reservoir is technically feasible, but the production efficiency is generally modest, with the low average gas production rate of 4.93 × 103 ST m3/d (ST represents the standard conditions) over a 1-year period. The hydrate dissociation region is significantly affected by the reservoir heterogeneity and reveals a heterogeneous dissociation front in the reservoir. The depressurization production results in significant increase of shear stress and vertical compaction in the hydrate reservoir. The response of shear stress indicates that the potential region of sand migration is mainly in the sand-dominant layer during gas production from the hydraulically heterogeneous hydrate reservoir (e.g., sand layers interbedded with clay layers). The maximum subsidence is approximately 78 mm and occurred at the 72nd day, whereas the final subsidence is slowly dropped to 63 mm after 1-year of depressurization production. The vertical subsidence is greatly dependent on the elastic properties and the permeability anisotropy. In particular, the maximum subsidence increased by approximately 81% when the ratio of permeability anisotropy was set at 5:1. Furthermore, the potential shear failure in the hydrate reservoir is strongly correlated to the in-situ stress state. For the normal fault stress regime, the greater the initial horizontal stress is, the less likely the hydrate reservoir is to undergo shear failure during depressurization production.

Unlocking By-Passed Oil with Autonomous Inflow Control Devices Through an Integrated Approach

2021 ◽  
Author(s):  
Pawan Agrawal ◽  
Sharifa Yousif ◽  
Ahmed Shokry ◽  
Talha Saqib ◽  
Osama Keshtta ◽  
...  
Keyword(s):  
Continuous Production ◽  
Oil Production ◽  
Gas Production ◽  
Oil Field ◽  
Production Performance ◽  
Fluid Distribution ◽  
Flow Profile ◽  
Horizontal Drain ◽  
Control Devices

Abstract In a giant offshore UAE carbonate oil field, challenges related to advanced maturity, presence of a huge gas-cap and reservoir heterogeneities have impacted production performance. More than 30% of oil producers are closed due to gas front advance and this percentage is increasing with time. The viability of future developments is highly impacted by lower completion design and ways to limit gas breakthrough. Autonomous inflow-control devices (AICD's) are seen as a viable lower completion method to mitigate gas production while allowing oil production, but their effect on pressure drawdown must be carefully accounted for, in a context of particularly high export pressure. A first AICD completion was tested in 2020, after a careful selection amongst high-GOR wells and a diagnosis of underlying gas production mechanisms. The selected pilot is an open-hole horizontal drain closed due to high GOR. Its production profile was investigated through a baseline production log. Several AICD designs were simulated using a nodal analysis model to account for the export pressure. Reservoir simulation was used to evaluate the long-term performance of short-listed scenarios. The integrated process involved all disciplines, from geology, reservoir engineering, petrophysics, to petroleum and completion engineering. In the finally selected design, only the high-permeability heel part of the horizontal drain was covered by AICDs, whereas the rest was completed with pre-perforated liner intervals, separated with swell packers. It was considered that a balance between gas isolation and pressure draw-down reduction had to be found to ensure production viability for such pilot evaluation. Subsequent to the re-completion, the well could be produced at low GOR, and a second production log confirmed the effectiveness of AICDs in isolating free gas production, while enhancing healthy oil production from the deeper part of the drain. Continuous production monitoring, and other flow profile surveys, will complete the evaluation of AICD effectiveness and its adaptability to evolving pressure and fluid distribution within the reservoir. Several lessons will be learnt from this first AICD pilot, particularly related to the criticality of fully integrated subsurface understanding, evaluation, and completion design studies. The use of AICD technology appears promising for retrofit solutions in high-GOR inactive strings, prolonging well life and increasing reserves. Regarding newly drilled wells, dedicated efforts are underway to associate this technology with enhanced reservoir evaluation methods, allowing to directly design the lower completion based on diagnosed reservoir heterogeneities. Reduced export pressure and artificial lift will feature in future field development phases, and offer the flexibility to extend the use of AICD's. The current technology evaluation phases are however crucial in the definition of such technology deployments and the confirmation of their long-term viability.

The Key Factors of Low-Frequency Electric Heating Assisted Depressurization Method in the Exploiting of Methane Hydrate Sediments

2021 ◽  
Author(s):  
Ermeng Zhao ◽  
Jian Hou ◽  
Yunkai Ji ◽  
Lu Liu ◽  
Yongge Liu ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Specific Heat ◽  
Specific Heat Capacity ◽  
Low Frequency ◽  
Electric Heating ◽  
Gas Production ◽  
Hydrate Decomposition ◽  
Hydrate Saturation ◽  
Production Behavior

Abstract Natural gas hydrate is widely distributed in the permafrost and marine deposits, and is regarded as an energy resource with great potential. The low-frequency electric heating assisted depressurization (LF-EHAD) has been proven to be an efficient method for exploiting hydrate sediments, which involves complex multi-physics processes, i.e. current conduction, multiphase flow, chemical reaction and heat transfer. The physical properties vary greatly in different hydrate sediments, which may profoundly affect the hydrate decomposition in the LF-EHAD process. In order to evaluate the influence of hydrate-bearing sediment properties on the gas production behavior and energy utilization efficiency of the LF-EHAD method, a geological model was first established based on the data of hydrate sediments in the Shenhu Area. Then, the influence of permeability, porosity, thermal conductivity, specific heat capacity, hydrate saturation and hydrate-bearing layer (HBL) thickness on gas production behavior is comprehensively analyzed by numerical simulation method. Finally, the energy efficiency ratio under different sediment properties is compared. Results indicate that higher gas production is obtained in the high-permeability hydrate sediments during depressurization. However, after the electric heating is implemented, the gas production first increases and then tends to be insensitive as the permeability decreases. With the increasing of porosity, the gas production during depressurization decreases due to the low effective permeability; while in the electric heating stage, this effect is reversed. High thermal conductivity is beneficial to enhance the heat conduction, thus promoting the hydrate decomposition. During depressurization, the gas production is enhanced with the increase of specific heat capacity. However, more heat is consumed to increase the reservoir temperature during electric heating, thereby reducing the gas production. High hydrate saturation is not conducive to depressurization because of the low effective permeability. After electric heating, the gas production increases significantly. High HBL thickness results in a higher gas production during depressurization, while in the electric heating stage, the gas production first increases and then remains unchanged with the increase of thickness, due to the limited heat supply. The comparison results of energy efficiency suggest that electric heating is more advantageous for hydrate sediments with low permeability, high porosity, high thermal conductivity, low specific heat capacity, high hydrate saturation and high HBL thickness. The findings in this work can provide a useful reference for evaluating the application of the LF-EHAD method in gas hydrate sediments.

Gas production enhancement effect of underlying gas on methane hydrates in marine sediments by depressurization

Fuel ◽  
2021 ◽  
pp. 122415
Author(s):  
Jie Zhao ◽  
Jia-nan Zheng ◽  
Shuang Dong ◽  
Mingjun Yang ◽  
Yongchen Song
Keyword(s):  
Marine Sediments ◽  
Gas Production ◽  
Methane Hydrates ◽  
Enhancement Effect

Experiments on methane hydrates formation in seabed deposits and gas recovery adopting carbon dioxide replacement strategies

2019 ◽  
Vol 148 ◽  
pp. 371-381 ◽  
Author(s):  
Federico Rossi ◽  
Alberto Maria Gambelli ◽  
Deepak Kumar Sharma ◽  
Beatrice Castellani ◽  
Andrea Nicolini ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Methane Hydrates ◽  
Gas Recovery

First Successful Autonomous ICD Pilot for GOR Management Across ADNOC Offshore

2021 ◽  
Author(s):  
Fazeel Ahmad ◽  
Zohaib Channa ◽  
Fahad Al Hosni ◽  
Salman Farhan Nofal ◽  
Ziad Talat Libdi ◽  
...  
Keyword(s):  
Oil Production ◽  
Pilot Project ◽  
Gas Production ◽  
Simulation Software ◽  
Production Performance ◽  
Production Operation ◽  
Open Hole ◽  
Early Production ◽  
Horizontal Wellbore ◽  
Selection Factors

Abstract The paper discusses the pilot project in ADNOC Offshore to assess the Autonomous Inflow Control Device (AICD) technology as an effective solution for increasing oil production over the life of the field. High rate of water and gas production in horizontal wells is one of the key problems from the commencement of operation due to the high cost of produced water and gas treatment including several other factors. Early Gas breakthrough in wells can result in shut-in to conserve reservoir energy and to meet the set GOR guidelines. The pilot well was shut-in due to high GOR resulted from the gas breakthrough. A pilot project was implemented to evaluate the ability of autonomous inflow control technology to manage gas break through early in the life of the well spanned across horizontal wellbore. And also to balance the production influx profile across the entire lateral length and to compensate for the permeability variation and therefore the productivity of each zone. Each compartment in the pilot well was equipped with AICD Screens and Swell-able Packers across horizontal open hole wellbore to evaluate oil production and defer gas breakthrough. Some AICDs were equipped with treatment valve for the compartments that needed acid simulation to enhance the effectiveness of the zone. The selection factors for installing number of production valves in the pilot well per each AICD was based on reservoir and field data. Pre-modeling of the horizontal wellbore section with AICD was performed using commercial simulation software (NETool). After the first pilot was completed, a detailed technical analysis was conducted and based on the early production results from the pilot well showed that AICD completions effectively managed gas production by delaying the gas break through and restricting gas inflow from the reservoir with significant GOR reduction ±40% compared to baseline production performance data from the open hole without AICD thus increasing oil production. The pilot well performed positively to the AICD completion allowing to produce healthy oil and meeting the guidelines. The early production results are in line with NETool simulation modelling, thereby increasing assurance in the methods employed in designing the AICD completion for the well and candidate selection. This paper discusses the successful AICD completion installation and production operation in pilot well in ADNOC Offshore to manage GOR and produced the well with healthy oil under the set guidelines. This will enable to re-activate wells shut-in due to GOR constraint to help meeting the sustainable field production target.

Sign in / Sign up

Export Citation Format

Share Document