Drilling System Optimization Leads to Expedited Wells Delivery

2021 ◽  
Author(s):  
Efe Mulumba Ovwigho ◽  
Saleh Al Marri ◽  
Abdulaziz Al Hajri
Keyword(s):  
Drill Pipe ◽  
System Optimization ◽  
Drill String ◽  
Stick Slip ◽  
Drilling Performance ◽  
Drilling Parameters ◽  
Single String ◽  
Innovative Solution ◽  
Open Hole ◽  
Weight On Bit

Abstract On a Deep Gas Project in the Middle East, it is required to drill 3500 ft of 8-3/8" deviated section and land the well across highly interbedded and abrasive sandstone formations with compressive strength of 15 - 35 kpsi. While drilling this section, the drill string was constantly stalling and as such could not optimize drilling parameters. Due to the resulting low ROP, it was necessary to optimize the Drill string in order to enhance performance. Performed dynamic BHA modelling which showed current drill string was not optimized for drilling long curved sections. Simulation showed high buckling levels across the 4" drill pipe and not all the weight applied on surface was transmitted to the bit. The drilling torque, flowrate and standpipe pressures were limited by the 4" drill pipe. This impacted the ROP and overall drilling performance. Proposed to replace the 4" drill pipe with 5-1/2" drill pipe. Ran the simulations and the model predicted improved drill string stability, better transmission of weights to the bit and increased ROP. One well was assigned for the implementation. Ran the optimized BHA solution, able to apply the maximum surface weight on bit recommended by the bit manufacturer, while drilling did not observe string stalling or erratic torque. There was also low levels of shocks and vibrations and stick-slip. Doubled the on-bottom ROP while drilling this section with the same bit. Unlike wells drilled with the previous BHA, on this run, observed high BHA stability while drilling, hole was in great shape while POOH to the shoe after drilling the section, there were no tight spots recorded while tripping and this resulted in the elimination of the planned wiper trip. Decision taken to perform open hole logging operation on cable and subsequently run 7-in liner without performing a reaming trip. This BHA has been adopted on the Project and subsequent wells drilled with this single string showed similar performance. This solution has led to average savings of approximately 120 hours per well drilled subsequently on this field. This consist of 80 hours due to improved ROP, 10 hrs due to the elimination of wiper trip and a further 30 hrs from optimized logging operation on cable. In addition, wells are now delivered earlier due to this innovative solution. This paper will show how simple changes in drill string design can lead to huge savings in this current climate where there is a constant push for reduction in well times, well costs and improved well delivery. It will explain the step-by-step process that was followed prior to implementing this innovative solution.

A Dynamic Model for Rotary Rock Drilling

1982 ◽  
Vol 104 (2) ◽  
pp. 108-120 ◽  
Author(s):  
I. E. Eronini ◽  
W. H. Somerton ◽  
D. M. Auslander
Keyword(s):  
Drill Pipe ◽  
Tooth Wear ◽  
Drill String ◽  
Rock Drilling ◽  
Large Power ◽  
Drilling Rig ◽  
Drilling Performance ◽  
Weight On Bit ◽  
Rotary Speed ◽  
Mud Pressure

A rock drilling model is developed as a set of ordinary differential equations describing discrete segments of the drilling rig, including the bit and the rock. The end segment consists of a description of the bit as a “nonideal” transformer and a characterization of the rock behavior. The effects on rock drilling of bottom hole cleaning, drill string-borehole interaction, and tooth wear are represented in the model. Simulated drilling under various conditions, using this model, gave results which are similar to those found in field and laboratory drilling performance data. In particular, the model predicts the expected relationships between drilling rate and the quantities, weight on bit, differential mud pressure, and rotary speed. The results also suggest that the damping of the longitudinal vibrations of the drill string could be predominantly hydrodynamic as opposed to viscous. Pulsations in the mud flow are found to introduce “percussive” effects in the bit forces which seem to improve the penetration rate. However, it is known from field observations that drill pipe movements, if strong enough, may induce mud pressure surges which can cause borehole and circulation problems. Bit forces and torques are shown to be substantially coupled and the influence of certain rock parameters on variables which are measurable either at the bit or on the surface support the expectation that these signals can furnish useful data on the formation being drilled. Other results, though preliminary, show that the effects of the lateral deflections of the drill string may be large for the axial bit forces and significant for the torsional vibrations. For the latter, the unsteady nature of the rotation above the bit increases and the resistance to rotation due to rubbing contact between the drill string and the wellbore accounts for very large power losses between the surface and the bit.

A Modular Mechanism for Downhole Weight-on-Bit and Torque Reaction in Small Diameter Boreholes

2021 ◽  
pp. 1-15
Author(s):  
Anirban Mazumdar ◽  
Stephen Buerger ◽  
Adam Foris ◽  
Jiann-cherng Su
Keyword(s):  
Axial Force ◽  
Small Diameter ◽  
Field Testing ◽  
Drill String ◽  
Force Transmission ◽  
Drilling Performance ◽  
Weight On Bit ◽  
In Series ◽  
Mechanical Devices ◽  
Scalable Design

Abstract Drilling systems that use downhole rotation must react torque either through the drill-string or near the motor to achieve effective drilling performance. Problems with drill-string loading such as buckling, friction, and twist become more severe as hole diameter decreases. Therefore, for small holes, reacting torque downhole without interfering with the application of weight-on-bit, is preferred. In this paper we present a novel mechanism that enables effective and controllable downhole weight on bit transmission and torque reaction. This scalable design achieves its unique performance through four key features: 1) mechanical advantage based on geometry, 2) direction dependent behavior using rolling and sliding contact, 3) modular scalability by combining modules in series, and 4) torque reaction and weight on bit that are proportional to applied axial force. As a result, simple mechanical devices can be used to react large torques while allowing controlled force to be transmitted to the drill bit. We outline our design, provide theoretical predictions of performance, and validate the results using full-scale testing. The experimental results include laboratory studies as well as limited field testing using a percussive hammer. These results demonstrate effective torque reaction, axial force transmission, favorable scaling with multiple modules, and predictable performance that is proportional to applied force.

Successful CWD Campaign in Turnkey Project with Potential Utilisation for Well Construction Optimisation

2021 ◽  
Author(s):  
Louis Frederic Antoine Champain ◽  
Syed Zahoor Ullah ◽  
Alexey Ruzhnikov
Keyword(s):  
Cost Effective ◽  
Drill String ◽  
Successful Implementation ◽  
Delivery Time ◽  
Wellbore Instability ◽  
Third Phase ◽  
Drilling Parameters ◽  
Open Hole ◽  
Bottom Hole Assembly ◽  
Full Throttle

Abstract Drilling and completion of the surface and intermediate sections in some fields is extremely challenging due to wellbore instability, especially accomplished with complete losses. Such circumstances lead to several time-consuming stuck pipe events, when existing standard ways of drilling did not lead to a permanent resolution of the problems. After exhausting the available conventional techniques without sustainable success, unorthodox solutions were required to justify the well delivery time and cost. Here comes the Casing While Drilling (CwD), being the most time and cost-effective solution to wellbore instability. CwD is introduced at full throttle aiming at the well cost reduction and well quality improvement. The implementation plan was divided in three phases. The first phase was a remedial solution to surface and intermediate sections drilling and casing off to prevent stuck pipe events and provide smooth well delivery performances. After successful implementation of CwD first phase, CwD was taken to the next level by shifting it from a mitigation to an optimization measure. Each step of CwD shoe-to-shoe operations was analysed to improve its performances: drill-out (D/O) of 18⅝-in shoe track with CwD, optimum drilling parameters per formation and CwD bit design. Implemented in 19 wells, CwD shoe-to-shoe performances have been brought up or even above standard rotary bottom hole assembly (BHA) benchmark. Planning for third phase is undergoing whereby CwD is aiming to optimize a well construction to reduce well delivery time, by combining surface and intermediate sections thus eliminating one casing string. Numerous challenges are being worked on including open hole (OH) isolation packer which conform to and seal with the borehole uneven surface. Special "for purpose built" expandable steel packer and stage tool have been manufactured and qualified for the specific application. A candidate well has been chosen and agreed for first trial. The key areas of improvement include, drilling and casing off the surface and intermediate sections while competing with standard rotary BHA performances and slimming down the well profile towards tremendous time and costs savings. This paper encompasses details of constructions of various wells with sufficient contingencies to combat any expected hole problems without compromising the well quality while keeping the well within budget and planned time. It also provides an analysis of the well trials that were executed during the implementation of first and second phases of CwD implementation and the captured lessons learnt which are being carried forward to the next phase. This paper provides the technique on how CwD can be used to help with three aspects of drilling, successfully mitigating holes problems by reducing OH exposure time and to eliminate drill string tripping and modifying conventional casing design to reduce well time and cost by eliminating one casing string.

Drilling Cutting Analysis to Assist Drilling Performance Evaluation in Hard Rock Hole Widening Operation

2020 ◽  
Author(s):  
Daiyan Ahmed ◽  
Yingjian Xiao ◽  
Jeronimo de Moura ◽  
Stephen D. Butt
Keyword(s):  
Performance Enhancement ◽  
Ore Deposits ◽  
Drilling Process ◽  
Rotary Drilling ◽  
Pilot Hole ◽  
Drilling Rig ◽  
Drilling Performance ◽  
Drilling Parameters ◽  
Weight On Bit ◽  
Drilling Operations

Abstract Optimum production from vein-type deposits requires the Narrow Vein Mining (NVM) process where excavation is accomplished by drilling larger diameter holes. To drill into the veins to successfully extract the ore deposits, a conventional rotary drilling rig is mounted on the ground. These operations are generally conducted by drilling a pilot hole in a narrow vein followed by a hole widening operation. Initially, a pilot hole is drilled for exploration purposes, to guide the larger diameter hole and to control the trajectory, and the next step in the excavation is progressed by hole widening operation. Drilling cutting properties, such as particle size distribution, volume, and shape may expose a significant drilling problem or may provide justification for performance enhancement decisions. In this study, a laboratory hole widening drilling process performance was evaluated by drilling cutting analysis. Drill-off Tests (DOT) were conducted in the Drilling Technology Laboratory (DTL) by dint of a Small Drilling Simulator (SDS) to generate the drilling parameters and to collect the cuttings. Different drilling operations were assessed based on Rate of Penetration (ROP), Weight on Bit (WOB), Rotation per Minute (RPM), Mechanical Specific Energy (MSE) and Drilling Efficiency (DE). A conducive schedule for achieving the objectives was developed, in addition to cuttings for further interpretation. A comprehensive study for the hole widening operation was conducted by involving intensive drilling cutting analysis, drilling parameters, and drilling performance leading to recommendations for full-scale drilling operations.

Experimental Investigation of the Stick-Slip Phenomena of the Drill Pipe

2015 ◽  
Author(s):  
Tokihiro Katsui ◽  
Yoshitomo Mogi ◽  
Tomoya Inoue ◽  
Chang-Kyu Rheem ◽  
Miki Y. Matsuo
Keyword(s):  
Drill Pipe ◽  
Small Time ◽  
Numerical Results ◽  
Experimental Results ◽  
Frictional Torque ◽  
Drill Bit ◽  
Stick Slip ◽  
Model Experiments ◽  
Pipe Model ◽  
Weight On Bit

The stick-slip is one of the critical problems for the scientific drilling, because it causes a crushing of the sampled layer. The present study investigates the characteristics of stick-slip phenomena of the drill pipe with the model experiments and numerical methods. The model experiments are carried out using a 1m length drill pipe model made with the Teflon. The angular velocity at the top and the bottom of the pipe are measured with the gyro sensor on some conditions of rotating speed at the pipe top and the weight on bit (load at the pipe bottom). The numerical simulations are also carried out to reproduce the stick-slip phenomena of the model experiments. The stick-slip is a kind of torsional vibration which is governed by the convection equation. By considering the boundary condition at the top and bottom of the pipe, we can obtain a neutral delayed differential equation (NDDE). The solutions of the NDDE is depend on not the initial value but the initial history of the solution, because NDDE contains a delayed function term. Therefore, it should be solved carefully to avoid the numerical error. The NDDE is solved with the 4th order Runge-Kutta scheme with very small time increment until the truncation error could be neglected. And also, we have found out that the effect of the initial history on the solution become to be very small after a certain period of time. The experimental results are compared with the numerical results under the same rotating condition. The experimental results of the stick-slip suggest that the period of the slip is mainly depend on the rotation speed at the pipe top and the magnitude of the slip is mainly depend on the weight on bit. Those characteristics of the stick-slip such as the period or the magnitude of slip are also obtained with the numerical calculations. However, in order to obtain an acceptable numerical results of NDDE, we have to adjust the frictional torque acting on the drill bit. Though, the frictional torque model was determined by reference to the measured torque at the top of the drill pipe model in the present study, it is desired to be improved. Therefore, the physical model of the frictional torque on the drill bit should be evaluated much carefully for the precise estimation of the stick slip in the future.

Experimentally-Tuned Mathematical Model for Drillstring Vibrations

2007 ◽  
Author(s):  
Y. A. Khulief ◽  
F. A. Al-Sulaiman
Keyword(s):  
Dynamic Models ◽  
Drilling Fluid ◽  
Experimental Studies ◽  
Published Data ◽  
Test Rig ◽  
Stick Slip ◽  
Multibody Model ◽  
Drilling Performance ◽  
Weight On Bit ◽  
Functional Operation

Field experience manifests that drillstring vibration is one of the major causes for a deteriorated drilling performance. It is crucial to understand the complex vibrational mechanisms experienced by a drilling system in order to better control its functional operation and improve its performance. Experimental studies of drillstring dynamics are essential to complement the theoretical studies, and to alleviate the complexity of such dynamic models. This paper presents an experimental investigation using a specially designed drilling test rig. The test rig can simulate the drillstring vibrational response due to various excitation mechanisms, which include stick-slip, well-borehole contact, and drilling fluid interaction. The test rig is driven by a variable speed motor which allows for testing different drilling speeds, while a magnetic tension brake is used to simulated stick-slip. In addition, a shaker is employed to excite the drillstring axially in order to simulate the weight-on-bit (WOB). The drillstring is instrumented for vibration measurements. The experimentally identified parameters are used to refine the finite element multibody model of the drillstring, which was derived earlier by the investigators [1]. Comparisons with published data demonstrate the reliability of the developed scheme for prediction of drillstring vibrations.

Model Development of Torsional Drillstring and Investigating Parametrically the Stick-Slips Influencing Factors

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Parimal Arjun Patil ◽  
Catalin Teodoriu
Keyword(s):  
Nonlinear Differential Equations ◽  
Torsional Oscillation ◽  
Stick Slip ◽  
Friction Forces ◽  
Rock Interaction ◽  
Torsional Oscillations ◽  
Drilling Performance ◽  
Bottom Hole ◽  
Drilling Parameters ◽  
Bottom Hole Assembly

Drillstring vibration is one of the limiting factors maximizing drilling performance. Torsional vibrations/oscillations while drilling is one of the sever types of drillstring vibration which deteriorates the overall drilling performance, causing damaged bit, failure of bottom-hole assembly, overtorqued tool joints, torsional fatigue of drillstring, etc. It has been identified that the wellbore-drillstring interaction and well face-drill bit interaction are the sources of excitation of torsional oscillations. Predrilling analysis and real time analysis of drillstring dynamics is becoming a necessity for drilling oil/gas or geothermal wells in order to optimize surface drilling parameters and to reduce vibration related problems. It is very challenging to derive the drillstring model considering all modes of vibrations together due to the complexity of the phenomenon. This paper presents the mathematical model of a torsional drillstring based on nonlinear differential equations which are formulated considering drillpipes and bottom-hole assembly separately. The bit–rock interaction is represented by a nonlinear friction forces. Parametric study has been carried out analyzing the influence of drilling parameters such as surface rotations per minute (RPM) and weight-on-bit (WOB) on torsional oscillations. Influences of properties of drillstring like stiffness and inertia, which are most of the times either unknown or insufficiently studied during modeling, on torsional oscillation/stick-slip is also studied. The influences of different rock strength on rate of penetration (ROP) considering the drilling parameters have also been studied. The results show the same trend as observed in fields.

scholarly journals Drilling Vibration Modes and Penetration Rate Modeling using Artificial Neural Network and Multiple Linear Regression Analysis in Khoman Formation at the Egyptian Western Desert

2021 ◽  
Author(s):  
Sherif A. Ezz ◽  
Mohamed S. Farahat ◽  
Said Kamel ◽  
Ahmed Z. Nouh
Keyword(s):  
Neural Network ◽  
Regression Analysis ◽  
Penetration Rate ◽  
Drill String ◽  
Western Desert ◽  
Circulation Rate ◽  
Vibration Level ◽  
Stick Slip ◽  
Weight On Bit ◽  
Rotary Speed

Abstract Drill string vibrations are one of the most serious problems encountered while drilling as the bit and drill string interaction with formations under certain drilling conditions usually induces complex shocks and vibrations into the drill string components resulting in premature failure of the equipment and reduced drilling penetration rate. In severe cases where shocks and vibrations accumulated into drill string till exceeded its maximum yield or torsional strength, fatigue will occur and thereby increase the field development costs associated with replacing damaged components, fishing jobs, lost-in-hole situations, and sidetracks. Thus, real-time monitoring for downhole generated vibrations and accordingly adjusting drilling parameters including weight on bit, rotary speed, and circulation rate play a vital role in reducing the severity of these undesirable conditions. Vibration optimization must be done incorporation with the penetration rate, as a minimum economical penetration rate is required by the operator. In this study, three penetration rate and vibration level models were developed for axial, lateral, and stick-slip drilling modes using both MATLAB™ Software neural network and multiple regression analysis. It is found that the three models' results for vibration level and penetration rate; as compared with those recorded drilling data; showed an excellent match within an acceptable error of average correlation coefficient (R) over 0.95. The prediction of penetration rate and vibration level is thoroughly investigated in different axial, lateral, and stick-slip vibration drilling modes to be able to best select the optimum safe drilling zone. It is found that the axial vibration could be dampened by gradually increasing the weight on bit and increasing rotary speed while both the lateral and torsional vibrations are enhanced by increasing the rotary speed and decreasing the weight on bit.

scholarly journals Drillstring Failure: Analytical and Experimental Approach

2019 ◽  
Vol 300 ◽  
pp. 04004
Author(s):  
Edris Hassan ◽  
Jamil Abdo ◽  
Jan Kwak ◽  
Abdullah Al Shabibi
Keyword(s):  
Torsional Vibration ◽  
Oil And Gas ◽  
Drill Pipe ◽  
Oil And Gas Industry ◽  
Drill String ◽  
Design Parameters ◽  
Experimental Investigations ◽  
Torsional Vibrations ◽  
Stick Slip ◽  
The Impact

Drilling is one of the costliest activities in oil and gas industry due to the complexity of interactions with downhole rock formation. Under such conditions, the uncertainty of drillstring behaviour increase and hence it becomes difficult to predict the causes, occurrences, and types of failures. Lateral and torsional vibrations often cause failure of Bottom Hole Assembly (BHA), drillstring failure, drill bit and wall borehole damages. In this work, a model is presented to determine the impact of lateral and torsional vibrations on a drillstring during the drilling operation. The model aims to mimic real drillstring behaviour inside a wellbore with regards to its dynamic movements due to multiple real situations such as eccentricity of collars, drill pipe sections, and stick-slip phenomena occurring due to the interaction of the bit and the drillstring with the well formation. The work aims to develop a basis for determining critical operating speeds and design parameters to provide safe drilling procedures and reduce drill string fatigue failure. Lagrangian approach is used in this study to attain drillstring lateral and torsional vibration coupling equations. The nonlinear equations are solved numerically to obtain the response of the system. In this work, we also present a brief description of an in-house constructed experimental setup. The setup has the capability to imitate the downhole lateral and torsional vibration modes. Parameters from the experimental investigations are incorporated for validation of the mathematical models and for prediction of the drillstring fatigue life. Such investigations are essential for oil and gas industries as they provide solutions and recommendations about operational speed, lateral and torsional amplitudes measurements and corrections, and the conditions for avoiding occurrence of natural frequencies of the system.

A New Analytical Model on Lateral Vibration and Impact of Drill String - Choice of Safe and Fast Drilling

2010 ◽  
Vol 29-32 ◽  
pp. 2350-2355
Author(s):  
Wei Liu ◽  
Ying Cao Zhou ◽  
Qing Zhao
Keyword(s):  
Analytical Model ◽  
Drill String ◽  
Lateral Vibration ◽  
Directional Drilling ◽  
Key Factors ◽  
Concentrated Mass ◽  
Mass Model ◽  
Drilling Parameters ◽  
Weight On Bit

The severe lateral vibration and impact of drill string will not only cause the damage of drill string but also have bad effects on the quality of directional drilling operation. It is difficult to control lateral vibration amplitude and impact intensity even with advanced measurement apparatus while drilling. So it is feasible to use a theoretic method to analyze and predict lateral vibration of drill string in order to adjust and optimize drilling parameters in real-time. On the basis of beam-column series and spring-concentrated mass model, a new analytical model is established to realize the control of lateral vibration and impact by controlling some key factors, such as under-gauge stabilizer, initial phase angle and initial deformation, WOB (weight on bit) and ROB (rotation of bit).

Sign in / Sign up

Export Citation Format

Share Document