Control of Heavy Metals and Organochlorines Using the Oil from Sludge Process

1990 ◽  
Vol 22 (12) ◽  
pp. 249-258 ◽  
Author(s):  
T. R. Bridle ◽  
I. Hammerton ◽  
C. K. Hertle
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Control Mechanisms ◽  
Sludge Dewatering ◽  
Water Board ◽  
Unit Operations ◽  
Set Up

A four month pilot plant program, evaluating all unit operations comprising an integrated Oil from Sludge (OFS) plant has been successfully completed for the Sydney Water Board. The unit operations of sludge dewatering, drying and conversion to oil in the patented OFS reactor system were set up at the Malabar Sewage Treatment Plant in Sydney. Pilot testing of the char combustor was conducted off site. Extensive heavy metal and organochlorine monitoring across each unit operation has revealed the following information. There is no loss of contaminants across the dewatering and drying operations. With the exception of arsenic and mercury, all heavy metals fed to the OFS reactor are retained in the char. Greater than 75% of PCB's and 85% of HCB present in sludge are destroyed in the OFS reactor. Greater than 99.7% of the heavy metals fed to the fluid bed combustor are retained in the ash (with exception of mercury, which reported 3% in the flue gas). The FBC ash is classified non-hazardous, using the Toxic Characteristic Leaching Procedure.No organochlorines were detected in the dryer or FBC off-gases. The OFS technology offers decoupling of heavy metal and organochlorine control mechanisms, thus allowing each to be optimally controlled.

Heavy metals in outflows from a sewage treatment plant and in waters and sediments of ponds supplied with them

2009 ◽  
Vol 38 (4) ◽  
Author(s):  
Stefan Tucholski ◽  
Kazimierz Markiewicz ◽  
Emilia Markiewicz ◽  
Marcin Duda
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Sewage Water ◽  
Post Treatment ◽  
Metal Concentrations ◽  
Heavy Metal Concentrations ◽  
System A

Heavy metals in outflows from a sewage treatment plant and in waters and sediments of ponds supplied with themThe examination of total amounts of heavy metals (Hg, Cd, Cu, Pb, Cr, Ni, Zn) was conducted in the outflow from a sewage treatment plant and in the waters and sediments of ponds supplied with them. As the water passed through the pond system, a decrease of heavy metal concentrations in the post-treatment sewage water supplying the ponds was observed. The highest concentrations of heavy metals were found in the outflow from the sewage treatment plant and lower concentrations were observed in the water of pond 1 (except for Zn), which was the direct receiver of post-treatment sewage, while the lowest values were noted in the final pond. The concentration of heavy metals in the sediments decreased in consecutive ponds. The highest concentrations were determined in the sediment of pond 1 that received the post-treatment sewage directly from the sewage treatment outflow, whereas the lowest values were estimated in the sediments of pond number 4, which was the final pond in the system.

Investigation of Heavy Metal Pollutants in a Sewage Treatment Plant of Changchun in Frozen Period

2011 ◽  
Vol 343-344 ◽  
pp. 1265-1268
Author(s):  
Ying Zi Lin ◽  
Chang Hu Cao ◽  
Jun Yin ◽  
Hai Jun Qi
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Wastewater Treatment ◽  
Wastewater Treatment Plant ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Metal Pollutants ◽  
Urban Sewage ◽  
Heavy Metal Pollutants

According to the heavy metal investigation of some practical data in Changchun sewage treatment plant. For wastewater treatment plant and the commonly used treatment process wastewater process of the distribution of heavy metals are analyzed. We studied the heavy metals pollutant removal efficiency of situation with A/O process of wastewater treatment plant in frozen period. And make a comparative analysis of heavy metals pilot plant and demonstration project in water, determine target pollutants and focus on removal. Thus, under low temperature conditions so as to sewage treatment plants effectively remove heavy metal pollutants to provide theoretical guidance for the control of urban sewage treatment by-product of the deposition process to improve the quality of urban sewage treatment and provide scientific basis.

scholarly journals Study on Heavy Metal Resistant Bacteria in Guheswori Sewage Treatment Plant

Our Nature ◽  
2009 ◽  
Vol 6 (1) ◽  
pp. 52-57 ◽  
Author(s):  
A. Rajbanshi
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Antibiotic Resistance ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Resistant Bacteria ◽  
Heavy Metal Resistant ◽  
Staphylococcus Spp ◽  
Multiple Tolerance

Removal of heavy metals from wastewater needs advance chemical technology and is more expensive too. The cheaper alternative for this is the bioremediation using heavy metals resistant microorganisms. In this study, 10 heavy metal resistant bacteria were isolated from oxidation ditch of wastewater treatment plant of Bagmati Area Sewerage Project. These include chromium resistant Staphylococcus spp, Escherichia coli, Klebsiella spp; cadmium resistant Acinetobacter spp, Flavobacterium spp, Citrobacter spp; nickel resistant Staphylococcus spp, Bacillus spp; copper resistant Pseudomonas spp; and cobalt resistant Methylobacterium spp. All the isolates showed high resistance to heavy metals with Minimum Inhibitor Concentration (MIC) for heavy metals ranging from 150 mug/ml to 500 mug/ml. Six resistant isolates showed multiple tolerance to heavy metals. All the 10 isolates also showed antibiotic resistance of which 10% were resistant to single antibiotic and 90% were multi-antibiotic resistant. Heavy metal tolerance test showed maximum microbial tolerance to chromium and minimum tolerance to nickel in mixed liquor sample of oxidation ditch.Keywords: Heavy metal resistant bacteria, multiple tolerance, antibiotic resistance, Guheswori Sewage Treatment Plantdoi: 10.3126/on.v6i1.1655Our Nature (2008)6:52-57

Effect of Wastewater on the Soil and Irrigation Process: A Laboratory Study

2017 ◽  
Vol 1 (1) ◽  
pp. 46-55 ◽  
Author(s):  
Athar Hussain ◽  
Manjeeta Priyadarshi ◽  
Saif Said ◽  
Suraj Negi
Keyword(s):  
Heavy Metals ◽  
Tap Water ◽  
Sewage Treatment ◽  
Daily Intake ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Treated Wastewater ◽  
Surface Water Resources ◽  
Industrial Sewage ◽  
Concentration Levels

Most of the industrial sewage effluents used for irrigation contains heavy metals which cause toxicity to crop plants as the soils are able to accumulate heavy metal for many years. The vegetables grown for the present study were irrigated with treated wastewater brought from a nearby full-scale sewage treatment plant at different compositions along with tap water as a control. The concentration levels of the Cd, Co, Cu, Mn and Zn in the soil were found to below the toxic limits as prescribed in literature. Daily Intake Metals (DIM) values suggest that the consumption of plants grown in treated wastewater and tap water is nearly free of risks, as the dietary intake limits of Cu, Fe, Zn and Mn. The Enrichment Factor for the treated wastewater irrigated soil was found in order Zn> Ni> Pb> Cr> Cu> Co> Mn> Cd. Thus, treated wastewater can be effectively used for irrigation. This will have twofold significant environmental advantages: (1) helpful to reduce the groundwater usage for irrigation and (2) helpful to reduce the stress on surface water resources.

Comparison of lime and alum as oily sludge conditioners

1997 ◽  
Vol 36 (12) ◽  
pp. 117-124 ◽  
Author(s):  
Tay Joo Hwa ◽  
S. Jeyaseelan
Keyword(s):  
Specific Resistance ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Oily Sludge ◽  
Sludge Dewatering ◽  
Capillary Suction ◽  
Sludge Cake ◽  
Solids Content ◽  
Optimum Chemical

Chemical conditioning improves sludge dewatering. Choice of chemical conditioners is very much dependent on the characteristics of the sludges and the type of dewatering devices. Lime, alum, ferric chloride and polyelectrolytes are commonly used chemical conditioners. Anaerobic digested sludge samples collected from a sewage treatment plant with different oil contents varying from 1.8% to 8.0% by weight have been examined in the laboratory to find out their specific resistance, capillary suction time and filter yield. Lime and alum were used separately as conditioners. Different dosages of conditioner varying from 2% to 12% by weight were used to determine the optimum chemical dosage for varying oil contents. Lime dosages of about 6% were found to yield favourable characteristics. Addition of alum decreases the specific resistances and capillary suction times of oily sludges rapidly up to 4% dosages. Alum dosages beyond 4% only increase the solids content in the sludge cake and increase the sludge volume to be handled. A correlation between CST and specific resistance to filtration was established. CST can be measured easily and quickly in the laboratories. Using the CST and the correlation a quick prediction on dewaterability can be established.

Conditioning of oily sludges with municipal solid wastes incinerator fly ash

1997 ◽  
Vol 35 (8) ◽  
pp. 231-238 ◽  
Author(s):  
Tay Joo Hwa ◽  
S. Jeyaseelan
Keyword(s):  
Heavy Metals ◽  
Fly Ash ◽  
Specific Resistance ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Solid Wastes ◽  
Municipal Solid Wastes ◽  
Capillary Suction ◽  
Optimum Dosage

Conditioning of sludges improves dewatering characteristics and reduces the quantity of sludge to be handled. Anaerobic digested sludge collected from a sewage treatment plant contained 1.8% to 8% oil. The increase of specific resistance and capillary suction time (CST) with increasing oil content observed in these samples indicates the interference of oil in dewatering. It has been found that addition of municipal solid wastes incinerator fly ash decreases the specific resistances and capillary suction times of oily sludges rapidly up to 3% dosage. Beyond 3% fly ash, the decrease is less significant and the solids content in the sludge cake increases. This optimum dosage remains the same for sludges with varying oil contents from 1.8% to 12%. The total suspended solids of filtrate decreases with fly ash dosage but the toxic concentrations of heavy metals increases considerably. However at the optimum dosage of 3%, concentrations of heavy metals are within the limits for discharging into the sewers. The correlations of CST with the dewatering characteristics such as specific resistance, filter yield and corrected filter yield are established. These correlations can be used to obtain a quick prediction on dewaterability.

The determination of heavy metals in domestic sewage treatment plant wastes

1973 ◽  
Vol 2 (4) ◽  
pp. 473-482 ◽  
Author(s):  
J. C. Van Loon ◽  
J. Lichwa ◽  
D. Ruttan ◽  
J. Kinrade
Keyword(s):  
Heavy Metals ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Domestic Sewage

scholarly journals Regulatory and technological prerequisites of the use of sewage sludge for the production of organic fertilizers

2020 ◽  
pp. 162-170
Author(s):  
R. Edgecock ◽  
V. V. Bratishko ◽  
I. V. Zinchenko ◽  
S. H. Karpus ◽  
D. O. Milko ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Sewage Sludge ◽  
Municipal Wastewater ◽  
Raw Materials ◽  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Raw Material ◽  
Organic Fertilizers ◽  
Mineral Fertilizers

Annotation Purpose. Summarize the regulatory and technological requirements for the production of organic (organo-mineral) fertilizers on the base of sewage sludge. Methods. Analysis and generalization of the requirements of regulatory documents on the management of organic waste and their use as raw materials for the production of organic fertilizers and soil improvers. Results. The current legislative, departmental and regulatory documentary base in Ukraine concerning the treatment of sediment resulting from biological sewage treatment at municipal wastewater treatment plants for its further use in agriculture as fertilizers is analysed. Indicators are identified and analysed to determine the possibility, feasibility, efficiency and scope of organic fertilizers produced using sewage sludge. The analysis of changes in the content of organic matter and total nitrogen in the sewage sludge during its storage at the sewage treatment plant sites is presented. The technological feasibility of using sludge of different shelf life in composting production has been determined. Conclusions 1. The regulatory framework of Ukraine contains a sufficiently complete list of indicators that should be met by organic raw materials (sewage sludge) for further use as organic fertilizers. Some of these indicators – bio security and heavy metals content – can be improved in the composting process of fertilizers. 2. Fresh sediment, as well as sediment accumulated in the last late autumn and winter periods, is of main value for use as a raw material in the production of organic fertilizers. 3. The use in the production of compost sludge stored on sludge sites for a period of half a year or more requires special control of the process of decontamination. In this case, it is advisable to use additional means of wastewater decontamination. Keywords: heavy metals, manure, humus, decontamination, composting, organic fertilizers, sewage sludge.

Toxicity assays and their evaluation on organic polymer flocculants used for municipal sludge dewatering

1998 ◽  
Vol 38 (7) ◽  
pp. 207-215 ◽  
Author(s):  
H. Takigami ◽  
N. Taniguchi ◽  
Y. Shimizu ◽  
S. Matsui
Keyword(s):  
Sewage Treatment ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Algal Growth ◽  
Pilot Scale ◽  
Organic Polymer ◽  
Municipal Sludge ◽  
Sludge Dewatering ◽  
Algal Toxicity ◽  
Reproduction Tests

The toxicity of organic polymer flocculants used for the dewatering of municipal sludge was evaluated by using two different toxicity assays: the Closterium ehrenbergii algal toxicity test and the Bacillus subtilis rec-assay. The algal toxicity of the effluents from a pilot-scale sewage treatment plant was investigated with and without the addition of a flocculant (0, 0.05, 0.10 and 0.20 mg/L). No clear evidence on the toxicity caused by the flocculant was observed on both asexual and sexual reproduction tests of C. ehrenbergii. It was also found that the algal growth inhibition of various types of flocculants (i.e., cationic, anionic, amphoionic and non-ionic) was in the order of 1 to 20 mg/L, which was mainly due to a molecular weight (MW) fraction of greater than 100,000. The results of the B. subtilis rec-assay for these flocculants indicated that eight out of ten cationic flocculants caused the direct DNA damage with LC50 =0.1 to 10 mg/L. One of the genotoxic flocculants was also fractionated into their components by MW. The experimental results showed that the lethal effects were mainly contributed by the polymer fraction of MW greater than 100,000, although the genotoxicity was not detected in that fraction. Therefore, the detected genotoxicity of the flocculants could be caused by the combined effects of various components, such as polymers, oligomers, monomers and additives.

The Transformation of Heavy Metal Be in Activated Sludge Process

2012 ◽  
Vol 178-181 ◽  
pp. 633-636 ◽  
Author(s):  
Feng Chen ◽  
Xiu Lian Zhu ◽  
Wei Yu
Keyword(s):  
Heavy Metal ◽  
Activated Sludge ◽  
Sewage Treatment ◽  
Great Influence ◽  
Sewage Treatment Plant ◽  
Treatment Plant ◽  
Urban Land Use ◽  
Huge Number ◽  
Sludge Treatment

Municipalsludge is refers to the product of sewage treatment plant, facing the huge number of municipalsludge, the disposal of the municipalsludge has aroused wide attention of all countries. Many studies consider that urban land use of the municipalsludge is the most effective method, However heavy metal accumulats in the sludge and the environment of the risk with agricultural appears day after day.The purpose of this study is: analysis the transfermation of heavy metals in the activated sludge system of various structures. put forward the solution of reducing heavy metal exceeded in the activated sludge treatment process.It appears that the coagulation can make colloid stabilized and sedimentation, can control the input of the heavy metal effectively; Adsorption of activated sludge to heavy metal is very fast, in 30 min basic reached adsorption balance, probably 80% or more;The change from oxygen to aerobic have great influence on Heavy metal biological adsorption;An aerobic digestion processes can reduce the volume and quality of sludge, but there is no enrichment role to heavy metal in sludge.

Sign in / Sign up

Export Citation Format

Share Document