Application of the down-flow fluidized bed to the anaerobic treatment of wine distillery wastewater

1998 ◽  
Vol 38 (8-9) ◽  
pp. 393-399 ◽  
Author(s):  
D. García-Bernet ◽  
P. Buffière ◽  
S. Elmaleh ◽  
R. Moletta
Keyword(s):  
Fluidized Bed ◽  
Red Wine ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Anaerobic Treatment ◽  
Organic Loading Rate ◽  
Rock Density ◽  
Start Up ◽  
Distillery Wastewater ◽  
Inverse Fluidized Bed

This paper presents the results of the operation of a down-flow anaerobic fluidized bed treating red wine distillery wastewater during 1.5 years (laboratory scale). The carrier employed was ground perlite, an expanded volcanic rock (density 213 kg m−1, diameter 0.968 mm). After a 2 months start-up period, organic loading rate (OLR) was increased stepwise by reducing hydraulic retention time (HRT). The system attained carbon removal efficiency rates between 75 and 95%, at a OLR of 17 kg TOC m−3 d−1 (total organic carbon), at an HRT of 0.35 days. The results observed showed that the inverse fluidized bed can be an interesting option for anaerobic wastewater treatment.

Start up of an anaerobic inverse turbulent bed reactor fed with wine distillery wastewater using pre-colonised bioparticles

2005 ◽  
Vol 51 (1) ◽  
pp. 153-158 ◽  
Author(s):  
C. Arnaiz ◽  
S. Elmaleh ◽  
J. Lebrato ◽  
R. Moletta
Keyword(s):  
Industrial Wastewater ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Oxygen Demand ◽  
Anaerobic Treatment ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Biofilm Reactors ◽  
Start Up ◽  
Distillery Wastewater

The long start-up period of fluidized bed biofilm reactors is a serious obstacle for their wide installation in the anaerobic treatment of industrial wastewater. This paper presents the results of an anaerobic inverse turbulent bioreactor treating distillery wastewater during 117 days of operation at a laboratory scale. The pre-colonized bioparticles for this work were obtained from a similar reactor processing the same wastewater and which had a start-up period of 3 months. The system attained carbon removal efficiency rates between 70 and 92%, at an organic loading rate of 30.6 kg m+3 d+1 (chemical oxygen demand) with a hydraulic retention time of 11.1 h. The results obtained showed that the start-up period of this kind of reactors can be reduced by 3 using pre-colonized bioparticles.

Anaerobic Treatment of Polyethylene Terephthalate (PET) Wastewater from Lab to Full Scale

1999 ◽  
Vol 40 (8) ◽  
pp. 229-236 ◽  
Author(s):  
F. Fdz-Polanco ◽  
M. D. Hidalgo ◽  
M. Fdz-Polanco ◽  
P. A. García Encina
Keyword(s):  
Polyethylene Terephthalate ◽  
Loading Rate ◽  
Treatment Plant ◽  
Textile Wastewater ◽  
Anaerobic Treatment ◽  
Cod Removal ◽  
Organic Loading Rate ◽  
Foam Formation ◽  
Organic Loading ◽  
Start Up

In the last decade Polyethylene Terephthalate (PET) production is growing. The wastewater of the “Catalana de Polimers” factory in Barcelona (Spain) has two main streams of similar flow rate, esterification (COD=30,000 mg/l) and textile (COD=4000 mg/l). In order to assess the anaerobic treatment viability, discontinuous and continuous experiments were carried out. Discontinuous biodegradability tests indicated that anaerobic biodegradability was 90 and 75% for esterification and textile wastewater. The textile stream revealed some tendency to foam formation and inhibitory effects. Nutrients, micronutrients and alkali limitations and dosage were determined. A continuous lab-scale UASB reactor was able to treat a mixture of 50% (v) esterification/textile wastewater with stable behaviour at organic loading rate larger than 12 g COD/l.d (0.3 g COD/g VSS.d) with COD removal efficiency greater than 90%. The start-up period was very short and the recuperation after overloading accidents was quite fast, in spite of the wash-out of solids. From the laboratory information an industrial treatment plant was designed and built, during the start-up period COD removal efficiencies larger than 90% and organic loading rate of 0.6 kg COD/kg VSS.d (5 kg COD/m3.d) have been reached.

Anaerobic treatment of a medium strength industrial wastewater at low-temperature and short hydraulic retention time: a pilot-scale experience

2011 ◽  
Vol 64 (8) ◽  
pp. 1629-1635 ◽  
Author(s):  
M. Esparza Soto ◽  
C. Solís Morelos ◽  
J. J. Hernández Torres
Keyword(s):  
Low Temperature ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Pilot Scale ◽  
Anaerobic Treatment ◽  
Uasb Reactor ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Processing Industry ◽  
Industry Wastewater

The aim of this work was to evaluate the performance of a pilot-scale upflow anaerobic sludge blanket (UASB) reactor during the treatment of cereal-processing industry wastewater under low-temperature conditions (17 °C) for more than 300 days. The applied organic loading rate (OLRappl) was gradually increased from 4 to 6 and 8 kg CODsol/m3d by increasing the influent soluble chemical oxygen demand (CODsol), while keeping the hydraulic retention time constant (5.2 h). The removal efficiency was high (82 to 92%) and slightly decreased after increasing the influent CODsol and the OLRappl. The highest removed organic loading rate (OLRrem) was reached when the UASB reactor was operated at 8 kg CODsol/m3d and it was two times higher than that obtained for an OLRappl of 4 kg CODsol/m3d. Some disturbances were observed during the experimentation. The formation of biogas pockets in the sludge bed significantly complicated the biogas production quantification, but did not affect the reactor performance. The volatile fatty acids in the effluent were low, but increased as the OLRappl increased, which caused an increment of the effluent CODsol. Anaerobic treatment at low temperature was a good option for the biological pre-treatment of cereal processing industry wastewater.

Start-Up Strategy to Achieve Excellent Efficiency of Degradation Acetate,Ethanol and Propionate in UASB

2011 ◽  
Vol 71-78 ◽  
pp. 2103-2106
Author(s):  
Ming Yue Zheng ◽  
Ming Xia Zheng ◽  
Kai Jun Wang ◽  
Hai Yan
Keyword(s):  
Loading Rate ◽  
Anaerobic Treatment ◽  
Upflow Anaerobic Sludge Blanket ◽  
Organic Loading Rate ◽  
Anaerobic Sludge ◽  
Organic Loading ◽  
Metabolic Intermediate ◽  
Loading Rates ◽  
Start Up ◽  
Anaerobic Sludge Blanket

The performance of upflow anaerobic sludge blanket (UASB) fed with three metabolic intermediate (acetate, ethanol, and propionate) respectively was studied. The degradation of metabolic intermediate were investigated to discuss the reason for propionate inhibition problem in anaerobic treatment. The hydraulic retention time (HRT) in the reactors started with 8.0h.The yield rate of biogas were 237ml/gCOD, 242ml/gCOD, 218ml/gCOD for acetate, ethanol and propionate, respectively when finishing start-up under OLR of 5.0 kgCOD/(m3·d) (HRT=9.6h).The HRT remained constant 9.6h,and the substrate concentration was gradually increased from 1,000 to 16,000mg/L as COD,and the organic loading rates(OLR) was from 3.0 to 40.0 kgCOD/(m3·d).The maximum propionate concentration was 41.6 gHPr-COD/L at the organic loading rate of 43.9 kgCOD/(m3·d) (HRT, 9.6h) as well as acetate and ethanol.

Kinetics of an anaerobic fluidized bed reactor using biolite carrier

1996 ◽  
Vol 23 (6) ◽  
pp. 1305-1315 ◽  
Author(s):  
R. Prakash ◽  
K. J. Kennedy
Keyword(s):  
Steady State ◽  
Fluidized Bed ◽  
Loading Rate ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Loading Rates ◽  
Start Up ◽  
Removal Efficiencies ◽  
Biofilm Development ◽  
Kinetics Of

Start-up and steady state operation of anaerobic fluidized bed reactors (AFBRs) with biolite as the inert carrier material was studied. Start-up and concomitant biofilm development of AFBRs was performed using two common start-up techniques, the maximum efficiency profile (MEP) technique and the maximum load profile (MLP) technique. The MEP start-up technique increases the volumetric organic loading rates to the reactor gradually and is tied to the removal efficiency of the process. The MLP start-up technique maintains a moderately high but constant volumetric organic loading rate irrespective of reactor performance. Using sucrose-based wastewater as feed, both start-up techniques led to equally fast biofilm development and start-up times of approximately 5 weeks. However, the MEP technique resulted in more stable controlled reactor operation during the start-up period. The quick start-up confirms the high compatibility of biolite for bio-adhesion and the development of a healthy active biofilm.High concentrations of biofilm biomass achieved in AFBRs (69 g volatile biofilm solids (VBS)/L of expanded bed volume at an organic loading rate of 25 g COD/(Lùd)) allowed the successful treatment of wastewaters at high organic loading rates and organic removal efficiencies. During steady state experiments, organic removal efficiencies over 80% were obtained for organic loading rates as high as 20 g COD/(L∙d). It was found that the dependence of removal efficiency on hydraulic retention time is influenced by substrate concentration. Total biofilm yield was determined to be 0.08 g VBS/g COD removed, demonstrating the low net synthesis of solids in the AFBR. AFBRs had an average solids retention time of 150 days, corresponding to a washout factor of 0.01. Extrinsic kinetics of the AFBRs was determined to be zero order with a maximum specific utilization rate of 0.48 g COD/(g VBS∙d).AFBRs used to treat municipal landfill leachate with a BOD5:COD ratio of 0.86 achieved steady state COD removal efficiencies that ranged from 70% to 87%, depending on the reactor organic loading rate and the concentration of the leachate being treated. During leachate treatment, biofilm biomass gradually became "mineralized" as a result of precipitation of metal sulfides and carbonates. This eventually resulted in a decrease in biofilm microbial activity and the need for higher pumping rates to maintain the same degree of bed expansion. Key words: anaerobic, biological fluidized bed reactor, biolite, landfill leachate, sucrose, modeling, start-up, steady state kinetics.

scholarly journals Effect of Hydraulic Retention Time (HRT) and Organic Loading Rate (OLR) to the Nata de coco Anaerobic Treatment Eficiency and its Wastewater Characteristics

2018 ◽  
Vol 38 (2) ◽  
pp. 160 ◽  
Author(s):  
Istna Nafi Azzahrani ◽  
Fanny Arivia Davanti ◽  
Ria Millati ◽  
Muhammad Nur Cahyanto
Keyword(s):  
Retention Time ◽  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Anaerobic Treatment ◽  
Organic Content ◽  
Anaerobic Digester ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Working Volume ◽  
Standard Rate

In this study, experiments were conducted to investigate the effect of hydraulic retention time (HRT) and organic loading rate (OLR) on process stability of nata de coco wastewater anaerobic treatment using semi-continuous digester. The standard-rate anaerobic digester with working volume of 8.5 L was used to investigate the effect of three different hydraulic retention times (15, 20, and 25 days), and a standard-rate anaerobic digester with working volume of 9.1 L was operated at different organic loading rates of 0.5, 1, and 1.5 g/L/day. The findings revealed that minimum HRT for nata de coco wastewater anaerobic treatment using semi-continuous digester was achieved at HRT 20 days. Based on data from this study, the reduction of organic content in nata de coco wastewater increased when OLR increased until 1 g/L/day. But then those parameters value decreased when OLR being increased further to 1.5 g/L/day. It showed that at 1.5 g/L/day the amount of substrate fed to the system was exceeding the total degradation capacity of methanogenic microorganisms, hence the organic overload happened and decreased the efficiency of organic content reduction in anaerobic treatment of nata de coco wastewater.

Study on Performance and Characteristic of Microorganisms in a Waste-to-Energy System

2012 ◽  
Vol 626 ◽  
pp. 625-630
Author(s):  
Amirhossein Malakahmad ◽  
Noor Ezlin Ahmad Basri ◽  
Sharom Md Zain
Keyword(s):  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Large Population ◽  
Energy System ◽  
Waste To Energy ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Kitchen Waste ◽  
Start Up

Performance and characterization of microorganisms in a laboratory-scale anaerobic baffled reactor (ABR) was studied. The ABR was fed continuously at organic loading rate (OLR) of 15.2 g COD/l.d with a substrate containing pre-tested combination of kitchen waste and activated sludge. The HRT (hydraulic retention time), C/N (carbon/nitrogen) and F/M (food/microorganisms) ratios were maintained at 3 d, 31.4 and 0.35 gCOD/gVSS.d, respectively. The amounts of fat, protein, cellulose, hemi-cellulose and lignin which are significant polymers for anaerobic digestion start-up were found to be in appropriate ranges. Results show reduction of pH in front compartments and its boost in successive compartments. This indicates proper placement of acidogens and methanogens in the ABR. Also, significant growth in height of ABR granule bed was observed in the system based on formation and retention of granules. Microorganism characterization reveals large population ofMethanosarcinain front part of the reactor although toward the end the amount forMethanosaetaincreased. WhileMethanobacterium,Methanosprilium,MethanococcusandMethanobrevibacterwere observed in the ABR, higher percentage ofMethanosarcinaandMethanotrixindicates production of methane from acetate conversion.

Enhanced Treatment of CSTR Anaerobic Digested Effluent from Poultry Wastewater by IC Reactor

2012 ◽  
Vol 433-440 ◽  
pp. 1239-1244
Author(s):  
Zhan Guang Liu ◽  
Xue Fei Zhou ◽  
Ya Lei Zhang ◽  
Hong Guang Zhu
Keyword(s):  
Hydraulic Retention Time ◽  
Loading Rate ◽  
Biogas Production ◽  
Granular Sludge ◽  
Anaerobic Treatment ◽  
Controlling Factors ◽  
Organic Loading Rate ◽  
Organic Loading ◽  
Internal Circulation ◽  
Poultry Wastewater

The feasibility of applying internal circulation (IC) reactor anaerobic treatment for effluent from a CSTR plant treating poultry wastewater was examined and the key controlling factors were explored. A continuous-flow IC reactor of 12.3L capacity inoculated with anaerobic granular sludge was operated for 98 days at 35±1°C. With corresponding organic loading rate of 1.5-3.5 kgCOD/m3•d at hydraulic retention time of 1.5d, the maximum volumetric biogas production rate of 1.2 m3/m3•d and tCOD (total COD) removal efficiency in the range of 70-80% was achieved. Therefore, IC reactor is competent to treat CSTR effluent from poultry wastewater. The decrease of sCOD (soluble COD) relative to tCOD and ammonia inhibition may lead to deterioration of IC reactor anaerobic treatment.

Sign in / Sign up

Export Citation Format

Share Document