scholarly journals Carbon capture for blackwater: chemical enhanced high-rate activated sludge process

2019 ◽  
Vol 80 (8) ◽  
pp. 1494-1504 ◽  
Author(s):  
Haixin Jiang ◽  
Xianchun Tang ◽  
Yexuan Wen ◽  
Yi He ◽  
Hongbin Chen
Keyword(s):  
Activated Sludge ◽  
Carbon Capture ◽  
Carbon Mineralization ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Appropriate Technology ◽  
Capture Efficiency ◽  
High Rate ◽  
Iron Salt ◽  
Carbon Recovery

Abstract Blackwater has more benefits for carbon recovery than conventional domestic wastewater. Carbon capture and up-concentration are crucial prerequisites for carbon recovery from blackwater, the same as domestic wastewater. Both chemical enhanced primary treatment (CEPT) and high-rate activated sludge (HRAS) processes have enormous potential to capture organics. However, single CEPT is subject to the disruption of influent sulfide, and single HRAS has insufficient flocculation capacity. As a result, their carbon capture efficiencies are low. By combining CEPT and HRAS with chemical enhanced high rate activated sludge (CEHRAS) process, the limitations of single CEPT and single HRAS offset each other. The carbon mineralization efficiency was significantly influenced by SRT rather than iron salt dosage. An iron dosage significantly decreased chemical oxygen demand (COD) lost in effluent. Both SRT and iron dosage had a significant influence on the carbon capture efficiency. However, HRT had no great impact on the organic mass balance. CEHRAS allowed up to 78.2% of carbon capture efficiency under the best conditions. The results of techno-economic analysis show that decreasing the iron salt dosage to 10 mg Fe/L could promise profiting for blackwater treatment. In conclusion, CEHRAS is a more appropriate technology to capture carbon in blackwater.

scholarly journals Colloids, flocculation and carbon capture – a comprehensive plant-wide model

2018 ◽  
Vol 79 (1) ◽  
pp. 15-25 ◽  
Author(s):  
Hélène Hauduc ◽  
Ahmed Al-Omari ◽  
Bernhard Wett ◽  
Jose Jimenez ◽  
Haydee De Clippeleir ◽  
...  
Keyword(s):  
Activated Sludge ◽  
Carbon Capture ◽  
Oxygen Demand ◽  
High Rate ◽  
Reactor Performance ◽  
Whole Plant ◽  
Solids Retention ◽  
Methane Potential ◽  
Intracellular Storage ◽  
Activated Sludge Systems

Abstract The implementation of carbon capture technologies such as high-rate activated sludge (HRAS) systems are gaining interests in water resource and recovery facilities (WRRFs) to minimize carbon oxidation and maximize organic carbon recovery and methane potential through biosorption of biodegradable organics into the biomass. Existing activated sludge models were developed to describe chemical oxygen demand (COD) removal in activated sludge systems operating at long solids retention times (SRT) (i.e. 3 days or longer) and fail to simulate the biological reactions at low SRT systems. A new model is developed to describe colloidal material removal and extracellular polymeric substance (EPS) generation, flocculation, and intracellular storage with the objective of extending the range of whole plant models to very short SRT systems. In this study, the model is tested against A-stage (adsorption) pilot reactor performance data and proved to match the COD and colloids removal at low SRT. The model was also tested on longer SRT systems where effluents do not contain much residual colloids, and digestion where colloids from decay processes are present.

scholarly journals Efficiency and Technological Reliability of Contaminant Removal in Household WWTPs with Activated Sludge

2021 ◽  
Vol 11 (4) ◽  
pp. 1889 ◽  
Author(s):  
Agnieszka Micek ◽  
Krzysztof Jóźwiakowski ◽  
Michał Marzec ◽  
Agnieszka Listosz ◽  
Tadeusz Grabowski
Keyword(s):  
Activated Sludge ◽  
Wastewater Treatment Plants ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Pollutant Removal ◽  
Treated Wastewater ◽  
Contaminant Removal ◽  
Nitrogen And Phosphorus ◽  
Wastewater Samples ◽  
Polish Law

The results of research on the efficiency and technological reliability of domestic wastewater purification in two household wastewater treatment plants (WWTPs) with activated sludge are presented in this paper. The studied facilities were located in the territory of the Roztocze National Park (Poland). The mean wastewater flow rate in the WWTPs was 1.0 and 1.6 m3/day. In 2017–2019, 20 series of analyses were done, and 40 wastewater samples were taken. On the basis of the received results, the efficiency of basic pollutant removal was determined. The technological reliability of the tested facilities was specified using the Weibull method. The average removal efficiencies for the biochemical oxygen demand in 5 days (BOD5) and chemical oxygen demand (COD) were 66–83% and 62–65%, respectively. Much lower effects were obtained for total suspended solids (TSS) and amounted to 17–48%, while the efficiency of total phosphorus (TP) and total nitrogen (TN) removal did not exceed 34%. The analyzed systems were characterized by the reliability of TSS, BOD5, and COD removal at the level of 76–96%. However, the reliability of TN and TP elimination was less than 5%. Thus, in the case of biogenic compounds, the analyzed systems did not guarantee that the quality of treated wastewater would meet the requirements of the Polish law during any period of operation. This disqualifies the discussed technological solution in terms of its wide application in protected areas and near lakes, where the requirements for nitrogen and phosphorus removal are high.

Biodegradation of aniline

1997 ◽  
Vol 36 (10) ◽  
pp. 53-63 ◽  
Author(s):  
Shabbir H. Gheewala ◽  
Ajit P. Annachhatre
Keyword(s):  
Activated Sludge ◽  
Ammonia Oxidation ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Inhibitory Effect ◽  
Synthetic Wastewater ◽  
Nitrifying Bacteria ◽  
Aquatic Life ◽  
Oxidation Rates ◽  
Batch Tests

Discharge of aniline to the environment must be controlled as aniline is toxic to aquatic life and also exerts additional oxygen demand due to nitrification reaction involved during its biodegradation. Organic carbonaceous removal by heterotrophs during aniline biodegradation releases NH4+ which is the substrate for autotrophic nitrifying bacteria. However, aniline is toxic to nitrifying bacteria and severely inhibits their activity. Accordingly, batch and continuous studies were conducted to assess the biodegradation of aniline and its inhibitory effect on nitrification. Synthetic wastewater was used as feed with aniline as sole carbon source for mixed microbial population. Experiments were conducted at ambient temperatures of 30–32°C. An aerobic activated sludge Unit was operated at an HRT of about 13 hours and SRT of about 12 days. Biomass from aerobic activated sludge process treating domestic wastewater was acclimatized to synthetic wastewater Containing aniline. Removal efficiencies more than 95% were obtained for feed aniline concentrations upto 350 mg/l with insignificant inhibition of nitrification due to aniline. Ammonia oxidation rates of about 20–115 mgNH4N/l/d were observed. Batch tests were carried out to test the inhibitory effects of high initial aniline concentrations on nitritication. Carbonaceous removal by heterotrophs proceeded rapidly within 4–6 hours with nitrification picking up as soon as aniline concentration dropped below 3–4 mg/l. For higher initial aniline concentration more than 250 mg/l, complete nitrification did not take place even after aniline Concentration dropped below 3–4 mg/l.

Modeling of organic substrate transformation in the high-rate activated sludge process

2015 ◽  
Vol 71 (7) ◽  
pp. 971-979 ◽  
Author(s):  
Thomas Nogaj ◽  
Andrew Randall ◽  
Jose Jimenez ◽  
Imre Takacs ◽  
Charles Bott ◽  
...  
Keyword(s):  
Activated Sludge ◽  
Extracellular Polymeric Substances ◽  
Oxygen Demand ◽  
Organic Substrate ◽  
High Rate ◽  
State Variables ◽  
Modified Model ◽  
Soluble Substrate ◽  
Substrate Model ◽  
Dual Substrate

This study describes the development of a modified activated sludge model No.1 framework to describe the organic substrate transformation in the high-rate activated sludge (HRAS) process. New process mechanisms for dual soluble substrate utilization, production of extracellular polymeric substances (EPS), absorption of soluble substrate (storage), and adsorption of colloidal substrate were included in the modified model. Data from two HRAS pilot plants were investigated to calibrate and to validate the proposed model for HRAS systems. A subdivision of readily biodegradable soluble substrate into a slow and fast fraction were included to allow accurate description of effluent soluble chemical oxygen demand (COD) in HRAS versus longer solids retention time (SRT) systems. The modified model incorporates production of EPS and storage polymers as part of the aerobic growth transformation process on the soluble substrate and transformation processes for flocculation of colloidal COD to particulate COD. The adsorbed organics are then converted through hydrolysis to the slowly biodegradable soluble fraction. Two soluble substrate models were evaluated during this study, i.e., the dual substrate and the diauxic models. Both models used two state variables for biodegradable soluble substrate (SBf and SBs) and a single biomass population. The A-stage pilot typically removed 63% of the soluble substrate (SB) at an SRT <0.13 d and 79% at SRT of 0.23 d. In comparison, the dual substrate model predicted 58% removal at the lower SRT and 78% at the higher SRT, with the diauxic model predicting 32% and 70% removals, respectively. Overall, the dual substrate model provided better results than the diauxic model and therefore it was adopted during this study. The dual substrate model successfully described the higher effluent soluble COD observed in the HRAS systems due to the partial removal of SBs, which is almost completely removed in higher SRT systems.

Comparative study of membrane bioreactor (MBR) and activated sludge processes in the treatment of Moroccan domestic wastewater

2018 ◽  
Vol 78 (5) ◽  
pp. 1129-1136 ◽  
Author(s):  
S. Kitanou ◽  
M. Tahri ◽  
B. Bachiri ◽  
M. Mahi ◽  
M. Hafsi ◽  
...  
Keyword(s):  
Activated Sludge ◽  
Membrane Bioreactor ◽  
Ceramic Membrane ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Pilot Scale ◽  
Quality Parameters ◽  
Effluent Quality ◽  
Conventional Activated Sludge ◽  
Activated Sludge Processes

Abstract The study was based on an external pilot-scale membrane bioreactor (MBR) with a ceramic membrane compared to a conventional activated sludge process (ASP) plant. Both systems received their influent from domestic wastewater. The MBR produced an effluent of much better quality than the ASP in terms of total suspended solids (TSS), 5-day biological oxygen demand (BOD5) and chemical oxygen demand (COD), total phosphorus (TP) and total nitrogen (TN). Other effluent quality parameters also indicated substantial differences between the ASP and the MBR. This study leads to the conclusion that in the case of domestic wastewater, MBR treatment leads to excellent effluent quality. Hence, the replacement of ASP by MBR may be justified on the basis of the improved removal of solids, nutrients, and micropollutants. Furthermore, in terms of reuse the high quality of the treated water allows it to be reused for irrigation.

scholarly journals Performance of Novel Contact Stabilization Activated Sludge System on Domestic Wastewater Treatment

2015 ◽  
Vol 19 (2) ◽  
pp. 7
Author(s):  
Andrés Felipe Torres Franco ◽  
Nancy Vásquez Sarria ◽  
Jenny Rodriguez Victoria
Keyword(s):  
Activated Sludge ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Growth Zone ◽  
Pilot Scale ◽  
Ammonia Nitrogen ◽  
Activated Sludge System ◽  
Suspended Growth ◽  
Removal Efficiencies ◽  
Final Effluent

A pilot-scale study was conducted to evaluate a traditional contact stabilization activated sludge system (CSASC) and a modified CSAS (CSASM) treating domestic wastewater. The CSASC system was comprised of a contact reactor (CR), a stabilization reactor (SR) and a secondary settler (SS); the CSASM included a second CR, a second SS (CR2 and SS2), and a modified SR (SRM) divided into four zones: an attached-suspended growth zone which allowed the system to reach an average sludge retention time close to 36 d and favored the occurrence of nitrification; an anoxic zone for denitrification occurrence; an aerated suspended growth zone with a high presence of organic carbon; and an additional aerated suspended growth zone with a high ammonia concentrations environment. The CSASC’s removal efficiencies of chemical oxygen demand (COD) and total ammonia nitrogen (TAN) were respectively 94±4 % and 53±12%; whereas CSASM’s efficiencies were 88±7% for COD and 92±7% for TAN. Concentrations of TAN and NO3 --N in the CSASC’s final effluent were 14.3±5.2 and 5.0±2.9 mg×L-1; and 4.8±4.4 and 9.1±5.8 mg×L-1 in the CSASM’s final effluent. Results demonstrated that the proposed configuration obtained higher nitrogen removal efficiencies than traditional CSAS.</p>

scholarly journals PENGARUH CO-PRECIPITATION BESI KLORIDA TERHADAP KINERJA LUMPUR AKTIF PADA PROSES PENGOLAHAN AIR LIMBAH DOMESTIK SINTETIK

REAKTOR ◽  
2015 ◽  
Vol 15 (3) ◽  
pp. 182
Author(s):  
Dian Fatikha Aristiami ◽  
I Nyoman Widiasa
Keyword(s):  
Activated Sludge ◽  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Suspended Solid ◽  
Volume Index ◽  
Sludge Volume Index ◽  
Mixed Liquor Suspended Solid ◽  
Effluent Quality ◽  
Co Precipitation ◽  
Settling Characteristics

The increase of population leads to an increase of the quantity of domestic wastewater. Activated sludge system is the most cost-efective to treat the domestic wastewater treatment. This study is aimed to evaluate the co-precipitation coagulant effect of FeCl3 on the growth of activated sludge, settling characteristics of the activated sludge, and effluent quality. sludge sedimentation characteristics (settling) as well as on the effluent quality. The activated sludge systems were operated in batch mode and synthetic domestic wastewaters with C:N:P ratio of 100:5:1 were used as feed wastewater. The growth of activated sludge was based on concentration of Mixed Liquor Suspended Solid (MLSS), settling characteristics of activated sludge was based on value of Sludge Volume Index (SVI), and effluent quality was based on turbidity, colour, N-ammonia concentration, and Chemical Oxygen Demand content. Results indicate that inhibition effect of FeCl3 to activated sludge activity was not significant at dosage ≤ 30 mg/L. Good settling characterisic (SVI 70-150 mg/L) was achieved at dosage of 20-30 mg/L. Finally, the best effluent quality, i.e. turbidity (9.4), colour (96), amonia removal (83.6%), and COD removal (72.97%), at dosage of 30 mg/L. Keywords: activated sludge; co-precipitation; domestic wastewater; wastewater treatment Abstrak Peningkatan jumlah penduduk mengakibatkan kenaikan jumlah air limbah domestik. Sistem lumpur aktif merupakan proses yang paling efektif untuk mengolah air limbah domestik. Penelitian ini bertujuan untuk mengevaluasi pengaruh co-precipitation koagulan FeCl3 terhadap pertumbuhan lumpur aktif, karakteristik pengendapan lumpur aktif, dan kualitas efluen. Sistem lumpur aktif dioperasikan secara curah dan umpan air limbah yang digunakan adalah air limbah domestik sintesis dengan rasio C:N:P = 100:5:1. Pertumbuhan lumpur aktif  berdasarkan konsentrasi Mixed Liquor Suspended Solid (MLSS), karakteristik pengendapan lumpur berdasarkan  nilai Sludge Volume Index (SVI), dan kualitas efluen berdasarkan tingkat kekeruhan, warna, kadar N-amonia dan kadar Chemical Oxygen Demand (COD). Hasil penelitian menunjukkan bahwa inhibisi FeCl3 terhadap aktivitas lumpur aktif tidak signifikan pada dosis ≤ 30 mg/L. Karakteristik pengendapan yang baik (SVI 70-150 mg/L) tercapai pada dosis 20-30 mg/L. Kualitas efluen terbaik, yaitu  kekeruhan (9,4),  warna (96), penyisihan amonia (83,6%) dan penyisihan COD (72,97%), pada dosis 30 mg/L. Kata kunci: lumpur aktif; co-precipitation; air limbah domestik; pengolahan air limbah  

The role of extracellular polymeric substances on carbon capture in a high rate activated sludge A-stage system

2017 ◽  
Vol 322 ◽  
pp. 428-434 ◽  
Author(s):  
Maureen N. Kinyua ◽  
Matthew Elliott ◽  
Bernhard Wett ◽  
Sudhir Murthy ◽  
Kartik Chandran ◽  
...  
Keyword(s):  
Activated Sludge ◽  
Carbon Capture ◽  
Extracellular Polymeric Substances ◽  
High Rate ◽  
Stage System

scholarly journals Performance evaluation of novel attached-growth high rate algal pond system with additional artificial illumination for wastewater treatment and nutrient recovery

2020 ◽  
Author(s):  
Kesirine Jinda ◽  
Thammarat Koottatep ◽  
Chawalit Chaiwong ◽  
Chongrak Polprasert
Keyword(s):  
Oxygen Demand ◽  
Domestic Wastewater ◽  
Cost Effective ◽  
High Rate ◽  
Nutrient Recovery ◽  
Growth Media ◽  
Light Sources ◽  
Attached Growth ◽  
Artificial Illumination ◽  
Conventional Systems

Abstract Domestic wastewater containing a high proportion of organic matter and nutrients is a serious pollution problem in developing countries. This study aimed to evaluate the performance of a novel attached-growth high rate algal pond (AG-HRAP) employing attached-growth media and artificial light sources for treating domestic wastewater and enhancing nutrient recovery. Light intensities in the range of 40–180 μmol/m2/s were used in the AG-HRAPs. The experimental results showed that the highest chemical oxygen demand (COD), total nitrogen (TN) and total phosphorus (TP) removal efficiencies of 88, 62 and 69%, respectively, were found at the hydraulic retention time (HRT) of 15 days and the average light intensity of 180 μmol/m2/s. Moreover, the effluent COD concentrations could meet Thailand's national discharge standard. The highest biomass and protein productivities of 54 ± 4 and 37 ± 8 g/m2/d, respectively, were found in the AG-HRAPs, which were higher than in previous studies of HRAPs. The Stover-Kincannon kinetic values for COD, TN and TP removals of the AG-HRAPs (R2 = 0.9) were higher than those of the conventional systems. Additionally, the novel AG-HRAP system could provide a highly cost-effective operation when compared to other microalgal systems.

Sign in / Sign up

Export Citation Format

Share Document