scholarly journals THE RAPID AND GREEN HAIR ANALYSIS METHOD DEVELOPMENT USING FTIR FOR PAPAVERINE HCL DETERMINATION

2019 ◽  
pp. 211-217 ◽  
Author(s):  
ILMA NUGRAHANI ◽  
STEPHANIE SULISTIANA ◽  
SLAMET IBRAHIM
Keyword(s):  
Hair Sample ◽  
Method Development ◽  
Limit Of Detection ◽  
Area Under The Curve ◽  
Forensic Analysis ◽  
Percent Recovery ◽  
Relative Standard ◽  
Validation Parameters ◽  
Limit Of Quantitation ◽  
Papaverine Hydrochloride

Objective: This study was aimed to develop a rapid analysis using FTIR (Fourier Transform Infra-Red) for papaverine hydrochloride (HCl) determination in the hair sample, supported by a mathematically manipulation; which never been reported before in toxicology and forensic analysis. Methods: Firstly, the method was checked its validity to ensure the feasibility for the quantitative purpose. The absorbance spectrums were collected by measure the drug, matrix, and its mixture. A spectra which showed the best specificity and linearity then was selected and derived. Afterwards, the area under the curve (AUC) was measured. A series of concentration was used for compose the calibration curve. Based on the result, some validation parameters were checked thoroughly. Further, for sample preparation, hair was collected non-invasively, then was decontaminated using soap. Next, it was immersed into a papaverine HCl solution at a concentration of 25 mg/ml along days. Finally, the amount of drugs absorbed were measured by the developed method using FTIR. Results: Experimental data showed that all validation parameters could be fulfilled by the developed method. The selected spectra for the content determination was 1320-1230 cm-1. Its linearity was represented by a correlation coefficient value (r) ≥ 0.9999, variation coefficient (Vxo) ≤ 2.0%. The limit of detection (LOD) was 0.00618% w/w, meanwhile, the limit of quantitation (LOQ) was 0.02060% w/w, respectively. The percent recovery was in the range 97-103% with the relative standard deviation (RSD) was ≤ 2.0%. The drug has detected after 72 h immersion, moreover, after 192 h the concentration gained was 0.1594±0.0011% w/w. Conclusion: As the conclusion, FTIR absorbance-derivative method is adequate as a rapid procedure for determine papaverine HCl in the hair sample. This method shows the appropriate of specificity, accuracy and precise. In addition, it shows the advantages of simplicity, green/eco-friendlier, and cost-efficiency.

scholarly journals Analytical method development and validation studies for the estimation of H2 receptor antagonist drug (Ranitidine)

2021 ◽  
Vol 7 (2) ◽  
pp. 85
Author(s):  
Renuka Manjunath ◽  
Deepak Kumar Jha
Keyword(s):  
Dosage Form ◽  
Method Development ◽  
Limit Of Detection ◽  
Pharmaceutical Preparation ◽  
H2 Receptor Antagonist ◽  
Pharmaceutical Dosage Form ◽  
Rp Hplc ◽  
Relative Standard ◽  
Validation Parameters ◽  
Limit Of Quantitation

<p class="abstract"><strong>Background:</strong> An analytical science in the development, finding a new molecules and procreation of pharmaceuticals has been an extensive approached. From the evaluation over small quantities of complex biological substances to the quality monitoring of the finished dosage form, the use on analytical technology know- how covers an ample thoroughness over techniques or disciplines.</p><p class="abstract"><strong>Methods:</strong> Reversed phase high performance liquid chromatography (RP-HPLC) approach has been promoted for the discernment over Ranitidine (RAN) within pharmaceutical dosage form split of RAN was accomplished inside a unaccompanied chromatographic run of an Phenomenix column size 5 μm 4.6x250 mm along with UV analysis at 227 nm wavelength, below isocratic conditions, using Ammonium acetate and Methanol (pH 6.0) in 80:20 ratio. Validation parameters had been observed in accordance with exhibit linearity, accuracy, precision, Limit of Quantitation and Limit of detection in conformity in imitation of ICH guidelines.  </p><p class="abstract"><strong>Results:</strong> The contemporary approached demonstrates significant linearity upon the range concerning 50-202.5 μg/ml for RAN followed by intra-day and inter-day precision, expressed so the relative standard deviation (RSD), on replicates is &lt;2.0 and accuracy among the range over 98-102%.</p><p class="abstract"><strong>Conclusions:</strong> The flourished RP-HPLC technique was once innovative, suitable for detecting RAN in pure form and in pharmaceutical preparation.</p>

scholarly journals Measurement of HDO Products Using GC-TCD: Towards Obtaining Reliable Analytical Data

2018 ◽  
Vol 5 (1) ◽  
pp. 1-11 ◽  
Author(s):  
Oman Zuas ◽  
Harry Budiman ◽  
Dieni Mansur ◽  
Muhammad Rizky Mulyana
Keyword(s):  
Method Development ◽  
Limit Of Detection ◽  
Analytical Data ◽  
Sample Treatment ◽  
Gaseous Products ◽  
Relative Standard ◽  
Validation Parameters ◽  
Limit Of Quantitation ◽  
Method Development And Validation ◽  
Development And Validation

Abstract This paper reported the method development and validation of a gas chromatography with thermal conductivity detector (GC-TCD) method for the measurement of the gaseous products of hydrodeoxygenation (HDO). The method validation parameters include selectivity, precision (repeatability and reproducibility), accuracy, linearity, limit of detection (LoD), limit of quantitation (LoQ), and robustness. The results showed that the developed method was able to separate the target components (H2, CO2, CH4 and CO) from their mixtures without any special sample treatment. The validated method was selective, precise, accurate, and robust. Application of the developed and validated GC-TCD method to the measurement of by-product components of HDO of bio-oil revealed a good performance with relative standard deviation (RSD) less than 1.0% for all target components, implying that the process of method development and validation provides a trustworthy way of obtaining reliable analytical data.

Rapid and Sensitive Liquid Chromatographic Method for Determination of Anastrozole in Different Polymer–Lipid Hybrid Nanoparticles

2021 ◽  
pp. 247263032098230
Author(s):  
Dilshad Ahmad ◽  
Faisal A. Al Meshaiti ◽  
Yazeed K. Al Anazi ◽  
Osama Al Owassil ◽  
Alaa Eldeen B. Yassin
Keyword(s):  
High Performance ◽  
Limit Of Detection ◽  
Reversed Phase ◽  
Hplc Method ◽  
Hybrid Nanoparticles ◽  
Array Detector ◽  
Relative Standard ◽  
Validation Parameters ◽  
Limit Of Quantitation ◽  
Inhibitor Drug

Anastrozole, an aromatase inhibitor drug, is used for the treatment of breast cancer in pre- and postmenopausal women. Anastrozole’s incorporation into nanoparticulate carriers would enhance its therapeutic performance. To perceive the exact loaded amount of drug in nanocarriers, a valid analytical method is required. The reversed-phase high-performance liquid chromatography (RP-HPLC) method was developed and validated by using the C18 column, 150 × 4.6 mm, 5 µm particle size, in isocratic mobile phase composed of 50:50 V/V (volume/volume) acetonitrile–phosphate buffer (pH 3) flowing at a rate of 1.0 mL/min, and a diode array detector (DAD) set at λmax = 215 nm. The validation parameters such as linearity, accuracy, specificity, precision, and robustness have proven the accuracy of the method, with the relative standard deviation percentage (% RSD) values < 2. The limit of detection of the method was found equal to 0.0150 µg/mL, and the limit of quantitation was 0.0607 µg/mL. The percent recovery of sample was in the range of 98.04–99.25%. The method has the advantage of being rapid with a drug retention time of 2.767 min, specific in terms of resolution of peaks void of interference with any of the excipients, and high reproducibility. This makes it highly applicable for quality control purposes.

scholarly journals Determination of Tianeptine in Tablets by High-Performance Liquid Chromatography with Fluorescence Detection

2007 ◽  
Vol 90 (3) ◽  
pp. 720-724
Author(s):  
Sevgi Tatar Ulu
Keyword(s):  
Lower Limit ◽  
High Performance ◽  
Limit Of Detection ◽  
Internal Standard ◽  
Linear Calibration ◽  
Fluorescence Detector ◽  
Relative Standard ◽  
Validation Parameters ◽  
Limit Of Quantitation

Abstract A sensitive and selective high-performance liquid chromatographic method has been developed for the determination of tianeptine (Tia) in tablets. The method is based on derivatization of Tia with 4-chloro-7-nitrobenzofurazan (NBD-Cl). A mobile phase consisting of acetonitrile10 mM orthophosphoric acid (pH 2.5; 77 + 23) was used at a flow rate of 1 mL/min on a C18 column. The Tia-NBD derivative was monitored using a fluorescence detector, with emission set at 520 nm and excitation at 458 nm. Gabapentin was selected as an internal standard. Linear calibration graphs were obtained in the concentration range of 45300 ng/mL. The lower limit of detection (LOD) was 10 ng/mL at a signal-to-noise ratio of 4. The lower limit of quantitation (LOQ) was 45 ng/mL. The relative standard values for intra- and interday precision were &lt;0.46 and &lt;0.57%, respectively. The recovery of the drug samples ranged between 98.89 and 99.85%. No chromatographic interference from the tablet excipients was found. The proposed method was validated in terms of precision, robustness, recovery, LOD, and LOQ. All the validation parameters were within the acceptance range. The proposed method was applied for the determination of Tia in commercially available tablets. The results were compared with those obtained by an ultraviolet spectrophotometric method using t- and F-tests.

scholarly journals ULTRAVIOLET-SPECTROPHOTOMETRIC METHOD DEVELOPMENT AND VALIDATION FOR THE DETERMINATION OF NORFLOXACIN PRESENT IN TASTE MASKED DRUG RESIN COMPLEX

2018 ◽  
Vol 11 (4) ◽  
pp. 244
Author(s):  
Ayya Rajendra Prasad ◽  
Jayanthi Vijaya Ratna
Keyword(s):  
Spectrophotometric Method ◽  
Absorption Maximum ◽  
Method Development ◽  
Limit Of Detection ◽  
Statistical Parameters ◽  
Limit Of Quantification ◽  
Relative Standard ◽  
Validation Parameters ◽  
Development And Validation

 Objective: The objective of this study was developed and validated a novel, specific, precise, and simple ultraviolet (UV)-spectrophotometric method for the estimation of norfloxacin present in taste masked drug-resin complex.Methods: UV-spectrophotometric determination was performed with ELICO SL 1500 UV-visible spectrophotometer using 0.1 N HCl as a medium. The spectrum of the standard solution was run from 200 to 400 nm range for the determination of absorption maximum (λ max). λ max of norfloxacin was found at 278 nm. The absorbance of standard solutions of 1, 2, 3, 4, and 5 μg/ml of drug solution was measured at an absorption maximum at 278 nm against the blank. Then, a graph was plotted by taking concentration on X-axis and absorbance on Y-axis which gave a straight line. Validation parameters such as linearity and range, selectivity and specificity, limit of detection (LOD) and limit of quantification (LOQ), accuracy, precision, and robustness were evaluated as per the International Conference on Harmonization (ICH) guidelines.Results: Linearity for the UV-spectrophotometric method was noted over a concentration range of 1–5 μg/ml with a correlation coefficient of 0.9995. The LOD and LOQ for norfloxacin were found at 0.39 μg/ml and 1.19 μg/ml, respectively. Accuracy was in between 99.00% and 99.17%. % relative standard deviation for repeatability, intraday precision, and interday precision was found to be 0.600, in between 0.291 and 0.410, and in between 0.682 and 1.439, respectively. The proposed UV spectrophotometric method is found to be robust.Conclusion: The proposed UV-spectrophotometric method was validated according to the ICH guidelines, and results and statistical parameters demonstrated that the developed method is sensitive, precise, reliable, and simple for the estimation of norfloxacin present in taste masked drug-resin complex.

Bioanalysis - Method Development, Validation, Sample Preparation, its Detection Techniques and its Application

2021 ◽  
pp. 297-305
Author(s):  
Seema R. Nikam ◽  
Amol S. Jagdale ◽  
Sahebrao S. Boraste ◽  
Shrikant B Patil
Keyword(s):  
Sample Preparation ◽  
Method Development ◽  
Limit Of Detection ◽  
Solid Phase ◽  
Bioequivalence Study ◽  
Time Frame ◽  
Biological Drugs ◽  
Detection Techniques ◽  
Validation Parameters ◽  
Limit Of Quantitation

Quantitatively measurements of chemical and biological drugs and their metabolites in the biological sample. This used in clinical and non-clinical studies. Non clinical including Pharmacokinetic and Toxic kinetic study, and clinical including Bioavailability, Bioequivalence study. This are play significant role and help in improvement in technology and analytical methods. Recent years have witnessed the introduction of several high- quality review articles into the literature covering various scientific and technical aspects of bioanalysis. Method validation and development use for the purpose of suitability of method for their intended purpose, this are important in Drug Discovery and Development. It including a validation parameters are Accuracy, Precision, Range, Calibration Curve, Recovery, Limit of Detection, Limit of Quantitation, Specificity, Selectivity and Stability, Ruggedness. This applicable in bio analysis, FDA and EMA guidelines. There are 3 main Extraction techniques used in sample preparation in bioanalysis is precipitation, liquid –liquid extraction, solid phase extraction. Detection of analyte by using hyphenated and chromatographic techniques like LC-MS/MS, HPLC, GC-MS. This LC-MS/MS is commonly used in a bioanalysis. This bio analysis study used in Pharmaceutical, Biomedical research purpose. Many challenges in pharmaceutical industry that fulfill by the utilization of analytical technologies and high-throughput automated platforms has been employed; in order to perform more experiments in a shorter time frame with increased data quality.

scholarly journals METHOD DEVELOPMENT AND VALIDATION FOR ANALYSIS OF DEOXYARBUTININ ANHYDROUS EMULSION SYSTEM USING HIGH-PERFORMANCE LIQUID CHROMATOGRAPHY

2019 ◽  
pp. 172-175 ◽  
Author(s):  
MUCHTARIDI MUCHTARIDI ◽  
IDA MUSFIROH ◽  
AHMAD FAUZI
Keyword(s):  
High Performance Liquid Chromatography ◽  
Liquid Chromatography ◽  
Analytical Method ◽  
High Performance ◽  
Method Development ◽  
Limit Of Detection ◽  
Internal Standard ◽  
Emulsion System ◽  
Relative Standard ◽  
Limit Of Quantitation

Objective: The aim of this study is to develop a simple, precise and accurate analytical method of deoxyarbutin in anhydrous emulsion system preparation. Methods: The analysis was conducted using high-performance liquid chromatography (HPLC). Chromatographic analysis was carried out using a reversed phase-C18 column. The mobile consists of two phases methanol and water (60: 40 v/v) at a flow rate of 1.0 ml/min. The determinations were performed using UV detector set at 225 nm. All validation procedures were added with hydroquinone as an internal standard. Results: The method showed coefficient correlation is 0.9978, relative standard deviation (RSD) smaller than 2%, Limit of Detection (LOD) and Limit of Quantitation (LOQ) are 0.599 µg/ml and 1.817 µg/ml respectively. The total amount deoxyarbutin in anhydrous emulsion preparation is 1.964+0.02 % with 98% recovery percentage. Conclusion: The developed HPLC analytical method meets the validation criteria made by International Conference on Harmonisation (ICH).

scholarly journals HPLC METHOD DEVELOPMENT AND VALIDATION FOR AZITHRO-MYCIN IN ORAL SUSPENSION

2019 ◽  
pp. 7-12
Author(s):  
Alok Pratap Singh ◽  
Iti Chauhan ◽  
Snigdha Bhardwaj ◽  
Praveen Gaur ◽  
S Sadish Kumar ◽  
...  
Keyword(s):  
Method Development ◽  
Limit Of Detection ◽  
Hplc Method ◽  
Uv Detector ◽  
Limit Of Quantification ◽  
Relative Standard ◽  
Validation Parameters ◽  
Wide Range ◽  
Tract Infections ◽  
Development And Validation

Introduction: Azithro-mycin a semi-synthetic, azalide congener of erythro-mycin indicated in the treatment of respiratory tract infections. Various methods available for determination of Azithro-mycin, but HPLC are most versatile one. Objective: The present study is based on the development and validation of a rapid, simple high performance liquid chromatography (HPLC) method equipped with UV detector for quantitative analysis of Azithro-mycin (AZN) in suspension. Material and methods: The Method was performed by using Hypersil BDS-C18 (250 mm × 4.6 mm i.d.) column MS-II, with an isocratic mobile phase of methanol, acetonitrile and phosphate buffer pH 8 (60:30:10; v/v) with run time 15 minutes. The determinations were performed at a flow rate of 1.0ml/min, and UV detector set at 212 nm. Result and Discussion: The method was found to be specific with relative standard deviation (RSD) less than 2.09%. The method showed accuracy with RSD less than 1.34% and precision in repeatability with RSD less than 1.42%. The method was found to be linear over a wide range of concentration from 1.0 to 50.0 μg/mL (R2 = .995). Limit of detection and limit of quantification were found to be 14.40 ng/mL and 43.66 ng/mL respectively. Conclusion: It was advantageous to use UV detector over other methods employing electrochemical, photodiode array etc. as the detector, because of cheap and easy availability. The developed method fulfilled all validation parameters as per ICH and can be successfully applied to quantify percent drug content in marketed oral Azithro-mycin suspension.

A Selective and Sensitive Method Development and Validation of 1,1-Dimethyl-3-Hydroxy-Pyrrolidinium Bromide Impurity in Glycopyrrolate Oral Solution by Liquid Chromatography–Tandem Mass Spectroscopy

2021 ◽  
Author(s):  
Rajesh Kumar Chawla ◽  
G S N Koteswara Rao ◽  
Umasankar Kulandaivelu ◽  
Siva Prasad Panda ◽  
Rajasekhar Reddy Alavala
Keyword(s):  
Liquid Chromatography ◽  
Mobile Phase ◽  
Method Development ◽  
Limit Of Detection ◽  
Oral Solution ◽  
Calibration Plot ◽  
Tandem Mass ◽  
Relative Standard ◽  
Limit Of Quantitation ◽  
Liquid Chromatography Tandem Mass

Abstract Objective A selective and sensitive liquid chromatography–tandem mass spectrometer (LC–MS/MS) method has been developed for the quantification of 1,1-dimethyl-3-hydroxy-pyrrolidinium bromide impurity in glycopyrrolate oral solution. Materials and method The LC–MS/MS analysis was done on X Bridge HILIC (100 × 4.6 mm, 5 μm) analytical column, and the mobile phase used was10 mM ammonium formate with 0.2% formic acid as mobile phase-A and acetonitrile as mobile phase-B with a gradient programme of 5.0 min. The flow rate used was 1.2 mL/min. Triple quadrupole mass detector coupled to positive electrospray ionization operated in multiple reactions monitoring mode was used for the quantification at m/z 116.10 ± 0.5. Results Retention time of impurity was found ~3.2 min. The method was validated in terms of specificity, linearity, accuracy, precision, range, limit of detection, limit of quantitation (LOQ) and robustness. Relative standard deviation (RSD) for system suitability was found 1.3%. Calibration plot was linear over the range of 0.050–2.000 μg/mL. Limit of detection and limit of quantification were found 0.017 and 0.051 μg/mL, respectively. The intra- and inter-day precision RSD was 2.3% and the obtained recovery at LOQ to 200% was in between 86.7 and 107.4%. Conclusion The low RSD values and high recoveries of the method confirm the suitability of the method.

scholarly journals Validation of High-Performance Liquid Chromatography Method for Determination of Vitamin B1 in Powder Milk

2020 ◽  
Vol 23 (5) ◽  
pp. 177-182
Author(s):  
Supriyono Supriyono ◽  
Mudhiah Fitrillah ◽  
Arie Pratama Putra
Keyword(s):  
Method Validation ◽  
Limit Of Detection ◽  
Milk Powder ◽  
Vitamin B1 ◽  
Enzymatic Reactions ◽  
System Suitability ◽  
Relative Standard ◽  
Validation Parameters ◽  
Limit Of Quantitation

Vitamin B1 plays an important role in the co-enzymatic reactions for energy-rich compounds called ATP (Adenosine Tri Phosphate). Therefore, it should be added to various food products, for example, milk powder. One method that can be used to determine vitamin B1 is SNI number 3751: 2009, but the method is intended for wheat flour. If the method is to be used for the analysis from other samples, such as milk powder, optimization, and validation, are needed. This experiment was carried out using HPLC, C18 column, and UV detector with a wavelength of 254 nm. The mobile phase used is methanol: acetic acid: bi-distilled water = 32:1:67 (v/v/v), flow rate = 1 mL/minute, isocratic, and reverse phased technique. Method validation parameters include tests of system suitability, linearity, the limit of detection, the limit of quantitation, precision (repeatability), and accuracy. The results showed that the system suitability test was obtained relative standard deviations (% RSD) for retention time and peak area, tailing factor, resolution, separation factor was 0.297%, 1.476%, 1.113, 6.693, and 4.406 respectively. The validation test gets a correlation coefficient (R) of 0.9996, the limit of detection and limit of quantitation were 0.0122 mg/100 mL and 0.0244 mg/100 mL, respectively. The precision test obtained Horwitz's ratio of 0.27%. Accuracy test using CRM obtained % recovery of 93.79-97.77%. All these results meet the requirements of method validation, so it can be concluded that the method of SNI number 3751: 2009 is valid for the determination of vitamin B1 in milk powder and can be used for routine analysis procedure.

Sign in / Sign up

Export Citation Format

Share Document