scholarly journals Estimation of wind turbine blade aerodynamic performances computed using different numerical approaches

2018 ◽  
Vol 45 (1) ◽  
pp. 53-65 ◽  
Author(s):  
Jelena Svorcan ◽  
Ognjen Pekovic ◽  
Toni Ivanov
Keyword(s):  
Wind Turbine ◽  
Thrust Force ◽  
Turbulence Models ◽  
Turbine Rotor ◽  
Momentum Balance ◽  
Horizontal Axis Wind Turbine ◽  
Ansys Fluent ◽  
Force Coefficients ◽  
Aerodynamic Performances ◽  
Numerical Approaches

Although much employed, wind energy systems still present an open, contemporary topic of many research studies. Special attention is given to precise aerodynamic modeling performed in the beginning since overall wind turbine performances directly depend on blade aerodynamic performances. Several models different in complexity and computational requirements are still widely used. Most common numerical approaches include: i) momentum balance models, ii) potential flow methods and iii) full computational fluid dynamics solutions. Short explanations, reviews and comparison of the existing computational concepts are presented in the paper. Simpler models are described and implemented while numerous numerical investigations of isolated horizontal-axis wind turbine rotor consisting of three blades have also been performed in ANSYS FLUENT 16.2. Flow field is modeled by Reynolds Averaged Navier-Stokes (RANS) equations closed by two different turbulence models. Results including global parameters such as thrust and power coefficients as well as local distributions along the blade obtained by different models are compared to available experimental data. Presented results include fluid flow visualizations in the form of velocity contours, sectional pressure distributions and values of power and thrust force coefficients for a range of operational regimes. Although obtained numerical results vary in accuracy, all presented numerical settings seem to slightly under- or over-estimate the global wind turbine parameters (power and thrust force coefficients). Turbulence can greatly affect the wind turbine aerodynamics and should be modeled with care.

scholarly journals Optimization of a Small Wind Turbine for a Rural Area: A Case Study of Deniliquin, New South Wales, Australia

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2292 ◽  
Author(s):  
Nour Khlaifat ◽  
Ali Altaee ◽  
John Zhou ◽  
Yuhan Huang ◽  
Ali Braytee
Keyword(s):  
Wind Turbine ◽  
Pitch Angle ◽  
New South ◽  
New South Wales ◽  
Turbulence Models ◽  
Weibull Function ◽  
Horizontal Axis Wind Turbine ◽  
Ansys Fluent ◽  
South Wales ◽  
Design Variables

The performance of a wind turbine is affected by wind conditions and blade shape. This study aimed to optimize the performance of a 20 kW horizontal-axis wind turbine (HAWT) under local wind conditions at Deniliquin, New South Wales, Australia. Ansys Fluent (version 18.2, Canonsburg, PA, USA) was used to investigate the aerodynamic performance of the HAWT. The effects of four Reynolds-averaged Navier–Stokes turbulence models on predicting the flows under separation condition were examined. The transition SST model had the best agreement with the NREL CER data. Then, the aerodynamic shape of the rotor was optimized to maximize the annual energy production (AEP) in the Deniliquin region. Statistical wind analysis was applied to define the Weibull function and scale parameters which were 2.096 and 5.042 m/s, respectively. The HARP_Opt (National Renewable Energy Laboratory, Golden, CO, USA) was enhanced with design variables concerning the shape of the blade, rated rotational speed, and pitch angle. The pitch angle remained at 0° while the rising wind speed improved rotor speed to 148.4482 rpm at rated speed. This optimization improved the AEP rate by 9.068% when compared to the original NREL design.

Bladelets—Winglets on Blades of Wind Turbines: A Multiobjective Design Optimization Study

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Sohail R. Reddy ◽  
George S. Dulikravich ◽  
Helmut Sobieczky ◽  
Manuel Gonzalez
Keyword(s):  
Wind Turbine ◽  
Design Optimization ◽  
Stokes Equations ◽  
Thrust Force ◽  
Flow Analysis ◽  
Turbine Rotor ◽  
Response Surfaces ◽  
Field Analysis ◽  
High Fidelity ◽  
Horizontal Axis Wind Turbine

The work presented in this paper used rigorous 3D flow-field analysis combined with multi-objective constrained shape design optimization for the design of complete blade + bladelet configurations for a three-blade horizontal-axis wind turbine. The fluid flow analysis in this work was performed using Openfoam software. The 3D, steady, incompressible, turbulent flow Reynolds-Averaged Navier–Stokes equations were solved in the rotating frame of reference for each combination of wind turbine blade and bladelet geometry. The free stream uniform wind speed in all cases was assumed to be 9 m s−1. The three simultaneous design optimization objectives were as follows: (a) maximize the coefficient of power, (b) minimize the coefficient of thrust force, and (c) minimize twisting moment around the blade axis. The bladelet geometry was fully defined by using a small number of parameters. The optimization was carried out by creating a multidimensional response surface for each of the simultaneous objectives. The response surfaces were based on radial basis functions, where the support points were designs analyzed using the high-fidelity computational fluid dynamics (CFD) analysis of the full blade + bladelet geometry. The response surfaces were then coupled to an optimization algorithm in modefrontier software. The predicted values of the objective functions for the optimum designs were then again validated using Openfoam high-fidelity analysis code. Results for a Pareto-optimized bladelet on a given blade indicate that more than 4% increase in the coefficient of power at minimal thrust force penalty is possible at off-design conditions compared to the same wind turbine rotor blade without a bladelet.

Comparison of Wind Tunnel Airfoil Performance Data With Wind Turbine Blade Data

1992 ◽  
Vol 114 (2) ◽  
pp. 119-124 ◽  
Author(s):  
C. P. Butterfield ◽  
George Scott ◽  
Walt Musial
Keyword(s):  
Wind Tunnel ◽  
Wind Turbine ◽  
Peak Power ◽  
Unsteady Aerodynamics ◽  
Leading Edge ◽  
Operating Conditions ◽  
Performance Data ◽  
Horizontal Axis Wind Turbine ◽  
Force Coefficients ◽  
Basic Fluid

Horizontal axis wind turbine (HAWT) performance is usually predicted by using wind tunnel airfoil performance data in a blade element momentum theory analysis. This analysis assumes that the rotating blade airfoils will perform as they do in the wind tunnel. However, when stall-regulated HAWT performance is measured in full-scale operation, it is common to find that peak power levels are significantly greater than those predicted. Pitch-controlled rotors experience predictable peak power levels because they do not rely on stall to regulate peak power. This has led to empirical corrections to the stall predictions. Viterna and Corrigan (1981) proposed the most popular version of this correction. But very little insight has been gained into the basic cause of this discrepancy. The National Renewable Energy Laboratory (NREL), funded by the DOE, has conducted the first phase of an experiment which is focused on understanding the basic fluid mechanics of HAWT aerodynamics. Results to date have shown that unsteady aerodynamics exist during all operating conditions and dynamic stall can exist for high yaw angle operation. Stall hysteresis occurs for even small yaw angles and delayed stall is a very persistent reality in all operating conditions. Delayed stall is indicated by a leading edge suction peak which remains attached through angles of attack (AOA) up to 30 degrees. Wind tunnel results show this peak separating from the leading edge at 18 deg AOA. The effect of this anomaly is to raise normal force coefficients and tangent force coefficients for high AOA. Increased tangent forces will directly affect HAWT performance in high wind speed operation. This report describes pressure distribution data resulting from both wind tunnel and HAWT tests. A method of bins is used to average the HAWT data which is compared to the wind tunnel data. The analysis technique and the test set-up for each test are described.

Navier-Stokes and Comprehensive Analysis Performance Predictions of the NREL Phase VI Experiment

2003 ◽  
Author(s):  
Earl P. N. Duque ◽  
Michael D. Burklund ◽  
Wayne Johnson
Keyword(s):  
Experimental Data ◽  
Wind Turbine ◽  
Turbine Rotor ◽  
Operating Conditions ◽  
Navier Stokes ◽  
Horizontal Axis Wind Turbine ◽  
Performance Predictions ◽  
Nasa Ames Research ◽  
Nrel Phase Vi ◽  
Wind Turbine Rotor

A vortex lattice code, CAMRAD II, and a Reynolds-Averaged Navier-Stoke code, OVERFLOW-D2, were used to predict the aerodynamic performance of a two-bladed horizontal axis wind turbine. All computations were compared with experimental data that was collected at the NASA Ames Research Center 80-by 120-Foot Wind Tunnel. Computations were performed for both axial as well as yawed operating conditions. Various stall delay models and dynamics stall models were used by the CAMRAD II code. Comparisons between the experimental data and computed aerodynamic loads show that the OVERFLOW-D2 code can accurately predict the power and spanwise loading of a wind turbine rotor.

Model Identification and Operating Load Characterization for a Small Horizontal Axis Wind Turbine Rotor Using Integrated Blade Sensors

2010 ◽  
Author(s):  
Scott Dana ◽  
Joseph Yutzy ◽  
Douglas E. Adams
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Rotor Blade ◽  
Model Identification ◽  
Turbine Rotor ◽  
Forced Response ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
And Control ◽  
Wind Turbine Rotor

One of the primary challenges in diagnostic health monitoring and control of wind turbines is compensating for the variable nature of wind loads. Given the sometimes large variations in wind speed, direction, and other operational variables (like wind shear), this paper proposes a data-driven, online rotor model identification approach. A 2 m diameter horizontal axis wind turbine rotor is first tested using experimental modal analysis techniques. Through the use of the Complex Mode Indication Function, the dominant natural frequencies and mode shapes of dynamic response of the rotor are estimated (including repeated and pseudo-repeated roots). The free dynamic response properties of the stationary rotor are compared to the forced response of the operational rotor while it is being subjected to wind and rotordynamic loads. It is demonstrated that both narrowband (rotordynamic) and broadband (wind driven) responses are amplified near resonant frequencies of the rotor. Blade loads in the flap direction of the rotor are also estimated through matrix inversion for a simulated set of rotor blade input forces and for the operational loading state of the wind turbine in a steady state condition. The analytical estimates are shown to be accurate at frequencies for which the ordinary coherence functions are near unity. The loads in operation are shown to be largest at points mid-way along the span of the blade and on one of the three blades suggesting this method could be used for usage monitoring. Based on these results, it is proposed that a measurement of upstream wind velocity will provide enhanced models for diagnostics and control by providing a leading indicator of disturbances in the loads.

scholarly journals Efficient contribution of partially tip cascaded horizontal-axis wind turbine

2019 ◽  
Vol 11 (11) ◽  
pp. 168781401989211
Author(s):  
Deyaa Nabil Elshebiny ◽  
Ali AbdelFattah Hashem ◽  
Farouk Mohammed Owis
Keyword(s):  
Wind Turbine ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
National Renewable Energy Laboratory ◽  
Horizontal Axis Wind Turbine ◽  
Ansys Fluent ◽  
Knowing That ◽  
Turbine Performance ◽  
Blade Tip

This article introduces novel blade tip geometric modification to improve the aerodynamic performance of horizontal-axis wind turbine by adding auxiliary cascading blades toward the tip region. This study focuses on the new turbine shape and how it enhances the turbine performance in comparison with the classical turbine. This study is performed numerically for National Renewable Energy Laboratory Phase II (non-optimized wind turbine) taking into consideration the effect of adding different cascade configurations on the turbine performance using ANSYS FLUENT program. The analysis of single-auxiliary and double-auxiliary cascade blades has shown an impact on increasing the turbine power of 28% and 76%, respectively, at 72 r/min and 12.85 m/s of wind speed. Knowing that the performance of cascaded wind turbine depends on the geometry, solidity and operating conditions of the original blade; therefore, these results are not authorized for other cases.

scholarly journals Aerodynamics and Modal Analysis for the Combined Vane type Vertical Axis Wind Turbine

2018 ◽  
Vol 7 (4.38) ◽  
pp. 1395 ◽  
Author(s):  
Kadhim H. Suffer ◽  
Yassr Y. Kahtan ◽  
Zuradzman M. Razlan
Keyword(s):  
Wind Turbine ◽  
Modal Analysis ◽  
Natural Frequencies ◽  
Turbine Blades ◽  
Vertical Axis ◽  
Turbine Rotor ◽  
Mode Shapes ◽  
Vertical Axis Wind Turbine ◽  
Ansys Fluent ◽  
Starting Torque

The present global energy economy suggests the use of renewable sources such as solar, wind, and biomass to produce the required power. The vertical axis wind turbine is one of wind power applications. Usually, when the vertical axis wind turbine blades are designed from the airfoil, the starting torque problem begins. The main objective of this research is to numerically simulate the combination of movable vanes of a flat plate with the airfoil in a single blade configuration to solve the starting torque problem. CFD analysis in ANSYS-FLUENT and structural analysis in ANSYS of combined blade vertical axis wind turbine rotor has been undertaken. The first simulation is carried out to investigations the aerodynamic characteristic of the turbine by using the finite volume method. While the second simulation is carried out with finite element method for the modal analysis to find the natural frequencies and the mode shape in order to avoid extreme vibration and turbine failure, the natural frequencies, and their corresponding mode shapes are studied and the results were presented with damping and without damping for four selected cases. The predicted results show that the static pressure drop across the blade increase in the active blade side because of the vanes are fully closed and decrease in the negative side because of the all the vanes are fully open. The combined blade helps to increase turbine rotation and so, thus, the power of the turbine increases. While the modal results show that until the 5th natural frequency the effect of damping can be neglected. The predicted results show agreement with those reported in the literature for VAWT with different blade designs.   

Numerical Studies of the Effects of Active and Passive Circulation Enhancement Concepts on Wind Turbine Performance

2006 ◽  
Vol 128 (4) ◽  
pp. 432-444 ◽  
Author(s):  
Chanin Tongchitpakdee ◽  
Sarun Benjanirat ◽  
Lakshmi N. Sankar
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Turbine Rotor ◽  
Horizontal Axis Wind Turbine ◽  
Trailing Edge ◽  
Low Wind Speed ◽  
Gurney Flap ◽  
Coanda Jet

The aerodynamic performance of a wind turbine rotor equipped with circulation enhancement technology (trailing-edge blowing or Gurney flaps) is investigated using a three-dimensional unsteady viscous flow analysis. The National Renewable Energy Laboratory Phase VI horizontal axis wind turbine is chosen as the baseline configuration. Experimental data for the baseline case is used to validate the flow solver, prior to its use in exploring these concepts. Calculations have been performed for axial and yawed flow at several wind conditions. Results presented include radial distribution of the normal and tangential forces, shaft torque, root flap moment, and surface pressure distributions at selected radial locations. At low wind speed (7m∕s) where the flow is fully attached, it is shown that a Coanda jet at the trailing edge of the rotor blade is effective at increasing circulation resulting in an increase of lift and the chordwise thrust force. This leads to an increased amount of net power generation compared to the baseline configuration for moderate blowing coefficients (Cμ⩽0.075). A passive Gurney flap was found to increase the bound circulation and produce increased power in a manner similar to Coanda jet. At high wind speed (15m∕s) where the flow is separated, both the Coanda jet and Gurney flap become ineffective. The effects of these two concepts on the root bending moments have also been studied.

Sign in / Sign up

Export Citation Format

Share Document