scholarly journals The influence of flow passage geometry on the performances of a supercritical CO2 centrifugal compressor

2018 ◽  
Vol 22 (Suppl. 2) ◽  
pp. 409-418 ◽  
Author(s):  
Dong-Bo Shi ◽  
Yu-Qi Wang ◽  
Yong-Hui Xie ◽  
Di Zhang
Keyword(s):  
Centrifugal Compressor ◽  
Supercritical Co2 ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Thermal Design ◽  
Original Design ◽  
Impeller Blade ◽  
Flow Passage ◽  
Ansys Cfx ◽  
Design Idea

In this paper, based on the thermodynamic design of the supercritical carbon dioxide (sCO2) centrifugal compressor, the design idea of the flow passage geometries and the method to improve the performance of the sCO2 centrifugal compressor are discussed. With the help of commercial software ANSYS CFX, the influence of the shape of the leading edge and trailing edge is studied, and the elliptical leading edge makes the pressure ratio 10.30% higher and the efficiency 3.95% higher than the square leading edge. By changing the forward-swept angle and backward-swept angle of the leading edge, the effects of aerodynamic swept shape in sCO2 centrifugal compressor are discussed. The effect of the gap between the impeller blade and diffuser blade is discussed, and the 10 mm gap makes the performance best. The pressure ratio is increased by 2.5% compared with the original design, while at the same time the efficiency is slightly improved. In summary, based on thermal design of the sCO2 centrifugal compressor, the effects of different flow geometries are analyzed in detail.

Numerical Efforts of Aerodynamic Re-Design in a Transonic Centrifugal Compressor: Part 1 — Basic Approach

2017 ◽  
Author(s):  
Justin (Jongsik) Oh
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Design Flow ◽  
Angle Distribution ◽  
Aerodynamic Design ◽  
Blade Angle ◽  
Original Design ◽  
Trailing Edge ◽  
Impeller Blade ◽  
Transonic Centrifugal Compressor

Growing demands for higher specific output power in turbomachinery applications have drawn attention to aerodynamic design philosophy for a single-stage transonic centrifugal compressor with higher pressure ratios. As Part 1 of numerical efforts, some fundamental approaches in aerodynamic design were carried out in a classical 6:1 pressure-ratio compressor design of 1970’s which was selected as a baseline. The effects of the impeller blade angle distribution, the addition of the splitter blade, the changes of the tangential divergence angle of the channel-wedge diffuser and some tweaks in diffuser vane shapes near the trailing-edge were investigated in steady-state RANS CFD solutions with the conventional mixing plane interface. New blade angle distributions together with the introduction of splitter blades in the impeller brought significant improvements in the compressor pressure ratio, efficiency and operability, thanks to reduced shock strengths and enhanced blade loadings in the spanwise direction. Helicity contours on the cross sectional planes in the impeller support the benefits observing a power balance among the shroud passage vortex, the blade vortices and the tip leakage vortex. With a reduced tangential divergence in the channel-wedge diffuser passage from the original design, an impressively extended surge margin was obtained. It was confirmed from the helicity contours that a streamwise vortex structure at the entrance region of the diffuser vane plays a key role in the range of operation. A diffuser vane shape with the curved pressure surface near the trailing-edge provided a slightly higher pressure ratio and efficiency around design flow than that with the original cut-off trailing-edge. An elliptical trailing-edge diffuser vane showed rather performance drops because of the counter-clockwise hub vortex breakdown near the suction surface, resulting in less flow diffusion. Through investigations of a set of design cases, two final compressor designs, differing in the diffuser vane shape near the trailing-edge, were obtained within the work scope of the present study. However, selecting one of the two will depend on design duties for the following component because of the level of exit swirls and their rate of changes over the flow rates.

The influence of the trailing edge angle of the micro centrifugal impeller on the performance of the centrifugal compressor

2021 ◽  
pp. 1-15
Author(s):  
Xu Yu-dong ◽  
Li Cong ◽  
Lv Qiong-ying ◽  
Zhang Xin-ming ◽  
Mu Guo-zhen
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Centrifugal Impeller ◽  
Centrifugal Compressors ◽  
Trailing Edge ◽  
Sweep Angle ◽  
Impeller Blade ◽  
Bending Angle ◽  
Edge Angle ◽  
Isentropic Efficiency

In order to study the effect of the trailing edge sweep angle of the centrifugal impeller on the aerodynamic performance of the centrifugal compressor, 6 groups of centrifugal impellers with different bending angles and 5 groups of different inclination angles were designed to achieve different impeller blade trailing edge angle. The computational fluid dynamics (CFD) method was used to simulate and analyze the flow field of centrifugal compressors with different blade shapes under design conditions. The research results show that for transonic micro centrifugal compressors, changing the blade trailing edge sweep angle can improve the compressor’s isentropic efficiency and pressure ratio. The pressure ratio of the compressor shows a trend of increasing first and then decreasing with the increase of the blade bending angle. When the blade bending angle is 45°, the pressure ratio of the centrifugal compressor reaches a maximum of 1.69, and the isentropic efficiency is 67.3%. But changing the inclination angle of the blade trailing edge has little effect on the isentropic efficiency and pressure ratio. The sweep angle of blade trailing edge is an effective method to improve its isentropic efficiency and pressure ratio. This analysis method provides a reference for the rational selection of the blade trailing edge angle, and provides a reference for the design of micro centrifugal compressors under high Reynolds numbers.

scholarly journals Experimental Investigation of Diffuser Hub Injection to Improve Centrifugal Compressor Stability

2005 ◽  
Vol 127 (1) ◽  
pp. 107-117 ◽  
Author(s):  
Gary J. Skoch
Keyword(s):  
Centrifugal Compressor ◽  
Surface Resistance ◽  
Flow Resistance ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Injection Rate ◽  
Flow Rates ◽  
Injection Flow ◽  
Air Supply ◽  
Series Of Experiments

Results from a series of experiments to investigate whether centrifugal compressor stability could be improved by injecting air through the diffuser hub surface are reported. The research was conducted in a 4:1 pressure ratio centrifugal compressor configured with a vane-island diffuser. Injector nozzles were located just upstream of the leading edge of the diffuser vanes. Nozzle orientations were set to produce injected streams angled at −8, 0, and +8 degrees relative to the vane mean camber line. Several injection flow rates were tested using both an external air supply and recirculation from the diffuser exit. Compressor flow range did not improve at any injection flow rate that was tested, and generally diminished as injection rate increased. Compressor flow range did improve slightly at zero injection due to the flow resistance created by injector openings on the hub surface. Resistance and flow range both increased as the injector orientation was turned toward radial. Leading edge loading and semivaneless space diffusion showed trends that are similar to those reported earlier from shroud surface experiments that did improve compressor range. Opposite trends are seen for hub injection cases where compressor flow range decreased. The hub injection data further explain the range improvement provided by shroud-side injection and suggest that stability factors cited in the discussion of shroud surface techniques are valid. The results also suggest that a different application of hub-side techniques may produce a range improvement in centrifugal compressors.

scholarly journals Aerodynamic and Structural Characteristics of a Centrifugal Compressor Impeller

2019 ◽  
Vol 9 (16) ◽  
pp. 3416 ◽  
Author(s):  
T R Jebieshia ◽  
Senthil Kumar Raman ◽  
Heuy Dong Kim
Keyword(s):  
Centrifugal Compressor ◽  
Structural Characteristics ◽  
Pressure Ratio ◽  
Operating Conditions ◽  
Von Mises Stress ◽  
Impeller Blade ◽  
Compressor Impeller ◽  
The One ◽  
Von Mises ◽  
Von Mises Stresses

The present study focuses on the aerodynamic performance and structural analysis of the centrifugal compressor impeller. The performance characteristics of the impeller are analyzed with and without splitter blades by varying the total number of main and splitter blades. The operating conditions of the compressor under centrifugal force and pressure load from the aerodynamic analysis are applied to the impeller blade and hub to perform the one-way Fluid–Structure Interaction (FSI). For the stress assessment, maximum equivalent von Mises stresses in the impeller blades are compared with the maximum allowable stress of the impeller material. The effects of varying the pressure field on the deformation and stress of the impeller are also calculated. The aerodynamic and structural performance of the centrifugal compressor at 73,000 rpm are investigated in terms of the efficiency, pressure ratio, equivalent von Mises stress, and total deformation of the impeller.

A Comparison of Two Fan Stage Designs With Different Rotor Leading Edge Sweep

2014 ◽  
Author(s):  
John Gunaraj ◽  
David Hanson ◽  
Jeffrey Hayes ◽  
Heath Lorzel ◽  
Nick Nolcheff ◽  
...  
Keyword(s):  
Pressure Ratio ◽  
Stability Margin ◽  
Leading Edge ◽  
Flow Capacity ◽  
Numerical Predictions ◽  
Performance Trends ◽  
Ansys Cfx ◽  
Significant Difference ◽  
Total Temperature ◽  
The Individual

Two modern single-stage fans have been designed to meet the same set of performance objectives. The most significant difference between the two designs is the fan rotor leading edge sweep. The baseline rotor has a moderately aft swept leading edge while the redesigned rotor has a more complex sweep distribution, including moderate forward sweep in the tip region. Each stage consists of the fan rotor, full span stator, and split mid-frame, and is designed for a medium bypass ratio turbofan application. The stator and the mid-frame are identical for the two configurations. The primary purpose of this study is to validate the CFD methodology, in this case a steady ANSYS-CFX approach, to predict the fan stage performance at the operating point at two tested speeds and also to predict the stalling throttle condition. Numerical predictions and engine test results are presented and show good agreement. These predicted results are compared with high quality test data including thorough measurements of total pressure and total temperature at both the rotor and stator exits allowing for a detailed understanding and comparison of the individual blade row performance. The analytical model identifies the key performance trends, including an increase in flow capacity and stability margin with equivalent stage pressure ratio and efficiency for the redesigned fan relative to the baseline.

scholarly journals Optimal Design of a Centrifugal Compressor Impeller Using Evolutionary Algorithms

2012 ◽  
Vol 2012 ◽  
pp. 1-22 ◽  
Author(s):  
Soo-Yong Cho ◽  
Kook-Young Ahn ◽  
Young-Duk Lee ◽  
Young-Cheol Kim
Keyword(s):  
Centrifugal Compressor ◽  
Optimization Algorithm ◽  
Pressure Ratio ◽  
Optimization Technique ◽  
Computational Time ◽  
Impeller Blade ◽  
Design Variables ◽  
Compressor Impeller ◽  
Artificial Neural Network Ann ◽  
Geometric Variation

An optimization study was conducted on a centrifugal compressor. Eight design variables were chosen from the control points for the Bezier curves which widely influenced the geometric variation; four design variables were selected to optimize the flow passage between the hub and the shroud, and other four design variables were used to improve the performance of the impeller blade. As an optimization algorithm, an artificial neural network (ANN) was adopted. Initially, the design of experiments was applied to set up the initial data space of the ANN, which was improved during the optimization process using a genetic algorithm. If a result of the ANN reached a higher level, that result was re-calculated by computational fluid dynamics (CFD) and was applied to develop a new ANN. The prediction difference between the ANN and CFD was consequently less than 1% after the 6th generation. Using this optimization technique, the computational time for the optimization was greatly reduced and the accuracy of the optimization algorithm was increased. The efficiency was improved by 1.4% without losing the pressure ratio, and Pareto-optimal solutions of the efficiency versus the pressure ratio were obtained through the 21st generation.

Centrifugal Compressor Blade Trimming for a Range of Flows

2001 ◽  
Author(s):  
C. Rodgers
Keyword(s):  
Centrifugal Compressor ◽  
Test Performance ◽  
Pressure Ratio ◽  
Performance Characteristics ◽  
Centrifugal Impeller ◽  
Impeller Blade ◽  
Flow Capacity ◽  
Component Test ◽  
Compressor Performance ◽  
Stage Efficiency

Centrifugal impeller blade trimming has long been used in the turbocharger industry to adapt a single impeller casting to a series of flow capacities, but surprisingly little published literature exists on the effects of trimming to compressor performance. This paper is presented as partial remedy, and describes the performance characteristics of a single stage centrifugal compressor designed and tested to cover a range of flow requirements by impeller blade and diffuser vane trimming. Stage and component test performance characteristics are presented for five trimmed flowpath contours covering a flow capacity range of approximately five to one at a DeLaval number of 0.75. The impeller tip diameter was 356mm, and the highest overall stage efficiency measured was 84.8% at an (air) pressure ratio of 1.5.

A Deep Insight Into the Transonic Flow of an Advanced Centrifugal Compressor Design

2019 ◽  
Author(s):  
D. Wittrock ◽  
M. Junker ◽  
M. Beversdorff ◽  
A. Peters ◽  
E. Nicke
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Free Form ◽  
Numerical Verification ◽  
Deep Insight ◽  
Flow Solver ◽  
Compressor Design ◽  
Design Speed

Abstract In the last decades major improvements in transonic centrifugal compressor design have been achieved. The further exploration of design space is enabled by recent progress in structural mechanics and manufacturing. A challenging task of inducer design especially in terms of transonic inflow conditions is to provide a wide flow range and reduced losses due to a sufficient shock control. The use of so called multidisciplinary design optimization with an extensive amount of free parameters leads finally to complex designs. DLR’s latest Fast Rotating Centrifugal Compressor (SRV5) operates at a design speed of Mu2 = 1.72 and a total pressure ratio of 5.72. This compressor design is characterized by an S-shaped leading edge and free-form blade surfaces. Due to the complex design the key design features are difficult to explore. Therefore, non-intrusive measurements are conducted on the highly loaded SRV5. The Laser-2-Focus (L2F) approach that is used in addition with the Doppler Global Velocimetry (DGV) delivers a three dimensional velocity field. Besides the impeller inflow the ouflow is also part of the experimental and numerical verification of the advanced compressor design. Experimental results are compared with the numerical analysis of the compressor using DLR’s RANS Flow Solver TRACE. The deep insight of the inflow leads to a better understanding of the operating behavior of such impeller designs.

Instantaneous Measurements in the Jet-Wake Discharge Flow of a Centrifugal Compressor Impeller

1975 ◽  
Vol 97 (3) ◽  
pp. 337-345 ◽  
Author(s):  
D. Eckardt
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Theoretical Models ◽  
Vaneless Diffuser ◽  
Impeller Blade ◽  
Measuring Systems ◽  
Compressor Design ◽  
Wake Patterns ◽  
Compressor Impeller ◽  
Critical Problems

One of the critical problems in centrifugal compressor design is the diffuser-impeller interaction. Up to now, theoretical models, which describe one of the salient features of this problem, the impeller discharge mixing process, appear to be proved experimentally only at low tip speeds. In the present study investigations on this subject were accomplished in the vaneless diffuser of a low-pressure ratio centrifugal compressor, running at tip speeds of 300 m/s. Detailed, instantaneous measurements in the impeller discharge mixing zone were performed by high-frequency measuring systems. Relative velocity distributions at the exit of impeller blade channels show pronounced jet/wake-patterns. The radial extension of flow distortions in the vaneless diffuser entry region, caused by rotating wakes, reached up to higher radius ratios than predicted by theoretical models.

Numerical Study on the Influence of Tip Clearance on Rotating Stall in an Unshrouded Centrifugal Compressor

2017 ◽  
Author(s):  
Wenying Ju ◽  
Shengli Xu ◽  
Xiaofang Wang ◽  
Xudong Chen ◽  
Shuhua Yang ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Leading Edge ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Forming Process ◽  
Impeller Blade ◽  
Tip Clearance Flow ◽  
Rotating Speed ◽  
Operation Conditions

Whole annulus unsteady simulations are performed by CFD with the whole flow passage model from inlet guide vanes to volute of an unshrouded centrifugal compressor. Characteristics and development mechanism of rotating stall are analyzed including the flow field and the impeller blade load in time and frequency domain. Rotating stall with three cells is observed in both two actual operation conditions but the cell rotating speed and the forming process is different. Leading edge tip clearance leakage is a criterion to predict the formation of a spike stall in centrifugal compressors. Tip clearance flow also plays an important role in the moving of rotating instabilities and the propagation of stall cells. It can effectively slow down the stall forming and decrease the pressure load on blade by reduced the tip clearance size at the leading edge.

Sign in / Sign up

Export Citation Format

Share Document