A Deep Insight Into the Transonic Flow of an Advanced Centrifugal Compressor Design

2019 ◽  
Author(s):  
D. Wittrock ◽  
M. Junker ◽  
M. Beversdorff ◽  
A. Peters ◽  
E. Nicke
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Free Form ◽  
Numerical Verification ◽  
Deep Insight ◽  
Flow Solver ◽  
Compressor Design ◽  
Design Speed

Abstract In the last decades major improvements in transonic centrifugal compressor design have been achieved. The further exploration of design space is enabled by recent progress in structural mechanics and manufacturing. A challenging task of inducer design especially in terms of transonic inflow conditions is to provide a wide flow range and reduced losses due to a sufficient shock control. The use of so called multidisciplinary design optimization with an extensive amount of free parameters leads finally to complex designs. DLR’s latest Fast Rotating Centrifugal Compressor (SRV5) operates at a design speed of Mu2 = 1.72 and a total pressure ratio of 5.72. This compressor design is characterized by an S-shaped leading edge and free-form blade surfaces. Due to the complex design the key design features are difficult to explore. Therefore, non-intrusive measurements are conducted on the highly loaded SRV5. The Laser-2-Focus (L2F) approach that is used in addition with the Doppler Global Velocimetry (DGV) delivers a three dimensional velocity field. Besides the impeller inflow the ouflow is also part of the experimental and numerical verification of the advanced compressor design. Experimental results are compared with the numerical analysis of the compressor using DLR’s RANS Flow Solver TRACE. The deep insight of the inflow leads to a better understanding of the operating behavior of such impeller designs.

A Deep Insight Into the Transonic Flow of an Advanced Centrifugal Compressor Design

2020 ◽  
Vol 142 (9) ◽  
Author(s):  
David Wittrock ◽  
Martin Junker ◽  
Manfred Beversdorff ◽  
Andreas Peters ◽  
Eberhard Nicke
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Navier Stokes ◽  
Free Form ◽  
Numerical Verification ◽  
Deep Insight ◽  
Compressor Design ◽  
Design Speed

Abstract In the last decades, major improvements in transonic centrifugal compressor design have been achieved. The further exploration of design space is enabled by recent progress in structural mechanics and manufacturing. A challenging task of inducer design especially in terms of transonic inflow conditions is to provide a wide flow range and reduced losses due to a sufficient shock control. The use of so-called multidisciplinary design optimization with an extensive amount of free parameters leads finally to complex designs. DLR’s latest fast rotating centrifugal compressor (SRV5) operates at a design speed of Mu2 = 1.72 and a total pressure ratio of 5.72. This compressor design is characterized by an S-shaped leading edge and free-form blade surfaces. Due to the complex design, the key design features are difficult to explore. Therefore, nonintrusive measurements are conducted on the highly loaded SRV5. The laser-2-focus (L2F) approach that is used in addition with the doppler-global-velocimetry (DGV) delivers a three-dimensional velocity field. Besides the impeller inflow, the outflow is also part of the experimental and numerical verification of the advanced compressor design. Experimental results are compared with the numerical analysis of the compressor using DLR’s Reynolds-averaged Navier–Stokes Flow Solver TRACE. The deep insight of the inflow leads to a better understanding of the operating behavior of such impeller designs.

Computation of Three-Dimensional Flow Fields Through Rotating Blade Rows and Comparison With Experiment

1982 ◽  
Vol 104 (2) ◽  
pp. 394-400 ◽  
Author(s):  
K. P. Sarathy
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Peak Efficiency ◽  
Three Dimensional Flow ◽  
Flow Solver ◽  
Rotating Blade ◽  
Blade Row ◽  
Time Marching ◽  
Design Speed

A three-dimensional inviscid time-marching calculation solving the unsteady Euler equations in a coordinate system rotating with the blade row has been developed, based on the Denton flow solver. This calculation was used to compute the flow field through the rotor of a transonic axial compressor and compared to measurements made with an advanced laser velocimeter at DFVLR. The comparison is made at design speed at pressure ratio corresponding to peak efficiency. Comparisons of the calculated and experimentally determined Mach number contours indicate excellent agreement in the entrance region where the viscous blockage effects are small. The methodology of the analysis is also described in this paper.

Investigation of a High Pressure Ratio Centrifugal Compressor with Wedge Diffuser and Pipe Diffuser

2017 ◽  
Vol 0 (0) ◽  
Author(s):  
Ge Han ◽  
Chengwu Yang ◽  
Shengfeng Zhao ◽  
Yanfeng Zhang ◽  
Xingen Lu
Keyword(s):  
Centrifugal Compressor ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Performance Comparison ◽  
Flow Solver ◽  
Rotating Speed ◽  
High Pressure Ratio ◽  
Flow Mechanisms ◽  
Operating Points

AbstractThis present work is aimed at providing detailed understanding of the flow mechanisms in a highly loaded centrifugal compressor with different diffusers. Performance comparison between compressor stages with pipe diffuser and wedge diffuser was conducted by a validated flow solver. Stage with pipe diffuser achieved a better performance above 80 % rotating speed but a worse performance at lower rotating speeds near surge. Four operating points including the design point were analyzed in detail. The inherent diffuser leading edge of pipe diffuser could create a better operating condition for the downstream diffusion, which reduced the possibility of flow separation in discrete passages at design rotating speed. At 60 % rotating speed operating point, there was a large negative incidence angle. The sharp leading edge of pipe diffuser could largely accommodate this negative incidence as comparison of the round leading edge of wedge diffuser. As a result, a better performance was achieved in the pipe diffuser. At 60 % rotating speed near surge, performance of the pipe diffuser dropped below wedge diffuser. Total pressure loss of pipe diffuser exceeded that of the wedge diffuser due to the larger friction loss near wall at throat and ineffective static pressure recovery.

Investigation of an Inversely Designed Centrifugal Compressor Stage—Part I: Design and Numerical Verification

2004 ◽  
Vol 126 (1) ◽  
pp. 73-81 ◽  
Author(s):  
M. Zangeneh ◽  
M. Schleer ◽  
F. Pløger ◽  
S. S. Hong ◽  
C. Roduner ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Design Method ◽  
Three Dimensional ◽  
Leading Edge ◽  
Inverse Design ◽  
Numerical Verification ◽  
Appreciable Effect ◽  
Tip Leakage Flow ◽  
Flow Angle ◽  
Blade Geometry

In this paper the three-dimensional inverse design code TURBOdesign-1 is applied to the design of the blade geometry of a centrifugal compressor impeller with splitter blades. In the design of conventional impellers the splitter blades normally have the same geometry as the full blades and are placed at mid-pitch location between the two full blades, which can usually result in a mismatch between the flow angle and blade angles at the splitter leading edge. In the inverse design method the splitter and full blade geometry is computed independently for a specified distribution of blade loading on the splitter and full blades. In this paper the basic design methodology is outlined and then the flow in the conventional and inverse designed impeller is compared in detail by using computational fluid dynamics (CFD) code TASCflow. The CFD results confirm that the inverse design impeller has a more uniform exit flow, better control of tip leakage flow and higher efficiency than the conventional impeller. The results also show that the shape of the trailing edge geometry has a very appreciable effect on the impeller Euler head and this must be accurately modeled in all CFD computations to ensure closer match between CFD and experimental results. Detailed measurements are presented in part II of the paper.

scholarly journals Genetic Algorithm Optimization of the Volute Shape of a Centrifugal Compressor

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Martin Heinrich ◽  
Rüdiger Schwarze
Keyword(s):  
Numerical Model ◽  
Centrifugal Compressor ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Pressure Rise ◽  
Maximum Efficiency ◽  
Algorithm Optimization ◽  
Cross Sectional ◽  
Design Variables ◽  
Design Speed

A numerical model for the genetic optimization of the volute of a centrifugal compressor for light commercial vehicles is presented. The volute cross-sectional shape is represented by cubic B-splines and its control points are used as design variables. The goal of the global optimization is to maximize the average compressor isentropic efficiency and total pressure ratio at design speed and four operating points. The numerical model consists of a density-based solver in combination with the SSTk-ωturbulence model with rotation/curvature correction and the multiple reference frame approach. The initial validation shows a good agreement between the numerical model and test bench measurements. As a result of the optimization, the average total pressure rise and efficiency are increased by over1.0%compared to the initial designs of the optimization, while the maximum efficiency rise is nearly 2.5% atm˙corr=0.19 kg/s.

Effect of Vaned Diffuser on a Modified Turbocharger Centrifugal Compressor Performance

2014 ◽  
Vol 663 ◽  
pp. 347-353
Author(s):  
Layth H. Jawad ◽  
Shahrir Abdullah ◽  
Zulkifli R. ◽  
Wan Mohd Faizal Wan Mahmood
Keyword(s):  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Width Ratio ◽  
Outlet Section ◽  
Suction Surface ◽  
Vaned Diffuser ◽  
Minimum Width

A numerical study that was made in a three-dimensional flow, carried out in a modified centrifugal compressor, having vaned diffuser stage, used as an automotive turbo charger. In order to study the influence of vaned diffuser meridional outlet section with a different width ratio of the modified centrifugal compressor. Moreover, the performance of the centrifugal compressor was dependent on the proper matching between the compressor impeller along the vaned diffuser. The aerodynamic characteristics were compared under different meridional width ratio. In addition, the velocity vectors in diffuser flow passages, and the secondary flow in cross-section near the outlet of diffuser were analysed in detail under different meridional width ratio. Another aim of this research was to study and simulate the effect of vaned diffuser on the performance of a centrifugal compressor. The simulation was undertaken using commercial software so-called ANSYS CFX, to predict numerically the performance charachteristics. The results were generated from CFD and were analysed for better understanding of the fluid flow through centrifugal compressor stage and as a result of the minimum width ratio the flow in diffuser passage tends to be uniformity. Moreover, the backflow and vortex near the pressure surface disappear, and the vortex and detachment near the suction surface decrease. Conclusively, it was observed that the efficiency was increased and both the total pressure ratio and static pressure for minimum width ratio are increased.

Generation Mechanism of Broadband Whoosh Noise in an Automotive Turbocharger Centrifugal Compressor

2021 ◽  
pp. 1-35
Author(s):  
Rick Dehner ◽  
Pranav Sriganesh ◽  
Ahmet Selamet ◽  
Keith Miazgowicz
Keyword(s):  
Centrifugal Compressor ◽  
Combustion Engine ◽  
Three Dimensional ◽  
Leading Edge ◽  
Broadband Noise ◽  
Rotor Blades ◽  
Generation Mechanism ◽  
Primary Concern ◽  
Frequency Range ◽  
Modal Decomposition

Abstract The present study focuses on the acoustics of a turbocharger centrifugal compressor from a spark-ignition internal combustion engine. Whoosh noise is typically the primary concern for this type of compressor, which is loosely characterized by broadband sound elevation in the 4 to 13 kHz range. To identify the generation mechanism of broadband whoosh noise, the present study combines three approaches: three-dimensional (3D) computational fluid dynamics (CFD) predictions, experiments, and modal decomposition of 3D CFD results. After establishing the accuracy of predictions, flow structures and time-resolved pressures are closely examined in the vicinity of the main blade leading edge. This reveals the presence of rotating instabilities that may interact with the rotor blades to generate noise. An azimuthal modal decomposition is performed on the predicted pressure field to determine the number of cells and the frequency content of these rotating instabilities. The strength of the rotating instabilities and the frequency range in which noise is generated as a consequence of the rotor-rotating instability interaction, is found to correspond well with the qualitative trend of the whoosh noise that is measured several duct diameters upstream of the rotor blades. The variation of whoosh frequency range between low and high rotational speeds is interpreted through this analysis. It is also found that the whoosh noise primarily propagates along the duct as acoustic azimuthal modes. Hence, the inlet duct diameter, which governs the cut-off frequency for multi-dimensional acoustic modes, determines the lower frequency bound of the broadband noise.

scholarly journals Experimental Investigation of Diffuser Hub Injection to Improve Centrifugal Compressor Stability

2005 ◽  
Vol 127 (1) ◽  
pp. 107-117 ◽  
Author(s):  
Gary J. Skoch
Keyword(s):  
Centrifugal Compressor ◽  
Surface Resistance ◽  
Flow Resistance ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Injection Rate ◽  
Flow Rates ◽  
Injection Flow ◽  
Air Supply ◽  
Series Of Experiments

Results from a series of experiments to investigate whether centrifugal compressor stability could be improved by injecting air through the diffuser hub surface are reported. The research was conducted in a 4:1 pressure ratio centrifugal compressor configured with a vane-island diffuser. Injector nozzles were located just upstream of the leading edge of the diffuser vanes. Nozzle orientations were set to produce injected streams angled at −8, 0, and +8 degrees relative to the vane mean camber line. Several injection flow rates were tested using both an external air supply and recirculation from the diffuser exit. Compressor flow range did not improve at any injection flow rate that was tested, and generally diminished as injection rate increased. Compressor flow range did improve slightly at zero injection due to the flow resistance created by injector openings on the hub surface. Resistance and flow range both increased as the injector orientation was turned toward radial. Leading edge loading and semivaneless space diffusion showed trends that are similar to those reported earlier from shroud surface experiments that did improve compressor range. Opposite trends are seen for hub injection cases where compressor flow range decreased. The hub injection data further explain the range improvement provided by shroud-side injection and suggest that stability factors cited in the discussion of shroud surface techniques are valid. The results also suggest that a different application of hub-side techniques may produce a range improvement in centrifugal compressors.

Flow Characteristics of a Novel Centrifugal Compressor Design

2016 ◽  
Author(s):  
Shashank Mishra ◽  
Shaaban Abdallah ◽  
Mark Turner
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Low Pressure ◽  
Flow Path ◽  
Optimization Techniques ◽  
Single Stage ◽  
Multi Stage ◽  
Compressor Design

Multistage axial compressor has an advantage of lower stage loading as compared to a single stage. Several stages with low pressure ratio are linked together which allows for multiplication of pressure to generate high pressure ratio in an axial compressor. Since each stage has low pressure ratio they operate at a higher efficiency and the efficiency of multi-stage axial compressor as a whole is very high. Although, single stage centrifugal compressor has higher pressure ratio compared with an axial compressor but multistage centrifugal compressors are not as efficient because the flow has to be turned from radial at outlet to axial at inlet for each stage. The present study explores the advantages of extending the axial compressor efficient flow path that consist of rotor stator stages to the centrifugal compressor stage. In this invention, two rotating rows of blades are mounted on the same impeller disk, separated by a stator blade row attached to the casing. A certain amount of turning can be achieved through a single stage centrifugal compressor before flow starts separating, thus dividing it into multiple stages would be advantageous as it would allow for more flow turning. Also the individual stage now operate with low pressure ratio and high efficiency resulting into an overall increase in pressure ratio and efficiency. The baseline is derived from the NASA low speed centrifugal compressor design which is a 55 degree backward swept impeller. Flow characteristics of the novel multistage design are compared with a single stage centrifugal compressor. The flow path of the baseline and multi-stage compressor are created using 3DBGB tool and DAKOTA is used to optimize the performance of baseline as well novel design. The optimization techniques used are Genetic algorithm followed by Numerical Gradient method. The optimization resulted into improvements in incidence and geometry which significantly improved the performance over baseline compressor design. The multistage compressor is more efficient with a higher pressure ratio compared with the base line design for the same work input and initial conditions.

Sign in / Sign up

Export Citation Format

Share Document