scholarly journals Experimental study on R1234yf heat pump at low ambient temperature and comparison with other refrigerants

2019 ◽  
Vol 23 (6 Part B) ◽  
pp. 3877-3886
Author(s):  
Shuxue Xu ◽  
Jianhui Niu ◽  
Guoyuan Ma
Keyword(s):  
Ambient Temperature ◽  
Heat Pump ◽  
Power Input ◽  
Coefficient Of Performance ◽  
Injection System ◽  
Pump System ◽  
Heat Pump System ◽  
Performance Improvements ◽  
Vapor Injection ◽  
Low Ambient Temperature

In this paper, an integrated vapor injection compression heat pump system using R1234yf, R32, R410A, R22, and R134a as working fluids was developed, and their heating performances under low ambient temperature were quantitatively evaluated. An experimental bench was built to test the system?s working performance. The condensing temperature, evaporating temperature, power input, and other variables were analyzed to evaluate the system?s heating capability and energy efficiency. Test results showed that the R1234yf system can run at the evaporating temperature of ?20 ?C, but its heating coefficient of performance was 5% lower than R134a. The R1234yf vapor injection system provided very significant performance improvements for heating performance compared with no vapor injection: the heating capacity and heating coefficient of performance can be improved by 14.3% and 11.7%, respectively.

Thermoeconomic Analysis on the Performance Characteristics of a Multi-Stage Irreversible Combined Heat Pump System

2000 ◽  
Vol 122 (4) ◽  
pp. 212-216 ◽  
Author(s):  
Jincan Chen ◽  
Chih Wu
Keyword(s):  
Heat Transfer ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Power Input ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Pump System ◽  
Heat Pump System ◽  
Maximum Profit ◽  
Multi Stage

A cycle model of a multi-stage combined heat pump system, which includes the irreversibility of finite rate heat transfer across finite temperature differences and the irreversibilities inside the working fluid, is established and used to investigate the influence of these irreversibilities on the performance of the system. The profit of operating the heat pump system is taken as an objective function for optimization. The maximum profit is calculated for a given total heat transfer area or total thermal conductance of heat exchangers. The coefficient of performance, heating load, and power input at the maximum profit are determined. The distribution of the heat transfer areas or the thermal conductances of heat exchangers and the temperature ratios of the working fluids of two adjacent cycles in heat exchange processes are optimized. The results obtained here are generally significant. They are suitable for an arbitrary-stage irreversible and endo- reversible combined heat pump system. [S0195-0738(00)01104-3]

scholarly journals Enhancing Heating Performance of Low-Temperature Air Source Heat Pumps Using Compressor Casing Thermal Storage

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3269 ◽  
Author(s):  
Zhongbao Liu ◽  
Fengfei Lou ◽  
Xin Qi ◽  
Yiyao Shen
Keyword(s):  
Low Temperature ◽  
Heat Pump ◽  
Waste Heat ◽  
Thermal Storage ◽  
Heat Pumps ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Heat Pump System ◽  
Discharge Temperature ◽  
Vapor Injection

Air source heat pumps (ASHPs) are widely recognized as energy-saving and environmentally friendly heating and air-conditioning equipment with broad applications. However, when conventional ASHPs are operated at a low ambient temperature, they suffer from problems such as high discharge temperature and low heating efficiency. To address these problems, this study designed a new type of dual evaporator combined with a compressor casing thermal storage heat pump system (DE-CCTS) on the basis of a low-temperature air source heat pump water heater with enhanced vapor injection (EVI). The proposed DE-CCTS used thermal storage phase change material (PCM), which was filled in the secondary evaporator (the thermal storage heat exchanger), to recover the waste heat of the compressor casing. Unlike that in the original system under different ambient temperatures, the suction temperature increased by 0.1–1 °C, the discharge temperature decreased by 0.1–0.5 °C, and the coefficient of performance (COP) of DE-CCTS increased by 0.85–4.72% under the proposed system. These effects were especially evident at low temperatures.

Performance Characteristics of a Combined Ejector-Absorption Heat Pump Using NH3-H2O

1999 ◽  
Author(s):  
D. A. Kouremenos ◽  
E. D. Rogdakis ◽  
G. K. Alexis
Keyword(s):  
Heat Pump ◽  
Gain Factor ◽  
Coefficient Of Performance ◽  
Detailed Calculation ◽  
Absorption System ◽  
Evaporator Temperature ◽  
Pump System ◽  
Heat Gain ◽  
Absorption Heat Pump ◽  
Heat Pump System

Abstract Absorption system have been investigated for many years. However, coefficient of performance COP or heat gain factor HGF for absorption systems are significantly lower than those for conventional compression systems. This has restricted their wide application. This paper discusses the behavior of mixture NH3-H2O through of an ejector, operating in an absorption heat pump system. This combination improves the performance of conventional absorption system and with the phasing out of ozone-damaging refrigerants, absorption refrigerators, heat pumps and air-conditioning now provide a potential alternative. For the detailed calculation of the proposed system a method has been developed, which employs analytical functions describing the thermodynamic properties of die mixture. The influence of three major parameters: generator, condenser and evaporator temperature, on ejector efficiency and heat gain factor of the system is discussed. Also the maximum value of HGF was estimated by correlation of above three temperatures.

Modeling of a Smart Heat Pump Made of Laminated Thermoelectric and Electrocaloric Materials

2016 ◽  
Vol 138 (4) ◽  
Author(s):  
Dudong Feng ◽  
Shi-Chune Yao ◽  
Tian Zhang ◽  
Qiming Zhang
Keyword(s):  
Heat Pump ◽  
Temperature Difference ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Laminated Structure ◽  
Heat Pump System ◽  
Simple Arrangement ◽  
Parametric Effects ◽  
Hybrid Heat Pump ◽  
Physical Features

In this study, a smart heat pump, which could be used for the cooling of electronics, made of laminated structure of thermoelectric (TE) and electrocaloric (EC) materials, is studied. A simple arrangement of two TE layers sandwiched with one EC layer is modeled. This smart heat pump utilized the newly developed EC materials of giant adiabatic temperature change and the TE materials of high figure of merit. The system has the advantages of no moving parts, made of solid state, operable over large working temperature difference, and can be formed into very small size. The operation of the device is numerically modeled considering the three major parametric effects: EC operation as a function of time, electric current applied on TE, and temperature difference between the hot and cold sinks. The results on coefficient of performance (COP) and heat flow per unit area are discussed. This study is performed as an early attempt of analyzing the basic physical features of TE–EC–TE laminated structure heat pump and extends the understanding by further discussing the tradeoff between lower COP and larger overall temperature difference coverage in the TE/EC hybrid heat pump system with multilaminated structure.

scholarly journals Theoretical Analysis of a Single-Stage Gas-fired Ejector Heat Pump Water Heater

2021 ◽  
pp. 1-28
Author(s):  
Jeremy Spitzenberger ◽  
Pengtao Wang ◽  
Laith Ismael ◽  
Hongbin Ma ◽  
Ahmad Abuheiba ◽  
...  
Keyword(s):  
Heat Pump ◽  
Thermal Energy ◽  
Ambient Air ◽  
Single Stage ◽  
Coefficient Of Performance ◽  
Water Heater ◽  
Pump System ◽  
Heat Pump System ◽  
Heating Capacity ◽  
Condenser Temperature

Abstract Ejector driven systems have the ability to operate at high efficiencies, utilizing recycled thermal energy as a power source. For a typical ejector heat pump system, the increase of the condenser temperature reduces the coefficient of performance (COP). In addition, if the condenser temperature is higher than the critical temperature, the ejector may not function. In this situation, the condenser temperature must be reduced, and an additional heater will be utilized to heat the production water from the condenser temperature to the desired temperature. In this investigation, a single-stage gas-fired ejector heat pump (EHP) is investigated and thermodynamically modeled in order to optimize the system COP for the purpose of heating water by utilizing the thermal energy from the ambient air. The effects of the high-temperature evaporator (HTE) and low-temperature evaporator (LTE) temperatures on the ejector critical back pressure and the EHP system performance are examined for a HTE temperature range of 120-180 °C and LTE temperatures of 15.5, 17.5, and 19.5 °C. Results show that an optimized COP of the EHP system exists which depends on HTE and LTE temperatures, primary nozzle throat diameters. In addition, it is found that the EHP COP is independent of the ejector COP. From this investigation a maximum EHP COP of 1.31 is able to be achieved for a HTE temperature of 160 °C and a LTE temperature of 19.5 °C with a total heating capacity of 15.98 kW.

The design of a seasonal heat storage system with a geothermal heat pump for a residential building in Tehran

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Akbar Alidadi Shamsabadi ◽  
Mehdi Jahangiri ◽  
Tayebeh Rezaei ◽  
Rouhollah Yadollahi Farsani ◽  
Ali Seryani ◽  
...  
Keyword(s):  
Heat Pump ◽  
Heating System ◽  
Coefficient Of Performance ◽  
Maximum Temperature ◽  
Software Environment ◽  
Geothermal Heat ◽  
Pump System ◽  
Matlab Software ◽  
Content Type ◽  
Heat Pump System

Purpose In this study, a solar water heating system along with a seasonal thermal energy storage and a heat pump is designed for a villa with an area of 192 m2 in Tehran, the capital of Iran. Design/methodology/approach According to the material and the area of the residential space, the required heating of the building was calculated manually and then the thermodynamic analysis of the system and simulation was done in MATLAB software. Finally, regarding the waste of system, an efficient solar heating system, providing all the required energy to heat the building, was obtained. Findings The surface area of the solar collector is equal to 46 m2, the capacity of the tank is about 2,850 m3, insulation thickness stands at 55 cm and the coefficient of performance in required heat pump is accounted to about 9.02. Also, according to the assessments, the maximum level of received energy by the collector in this system occurs at a maximum temperature of 68ºC. Originality/value To the best of the authors’ knowledge, in the present work, for the first time, using mathematical modeling and analyzing of the first and second laws of thermodynamics, as well as using of computational code in MATLAB software environment, the solar-assisted ground source heat pump system is simulated in a residential unit located in Tehran.

Experimental Study of Heating-Cooling Combined Ground Source Heat Pump System with Horizontal Ground Heat Exchanger

2011 ◽  
Vol 374-377 ◽  
pp. 398-404 ◽  
Author(s):  
Ying Ning Hu ◽  
Ban Jun Peng ◽  
Shan Shan Hu ◽  
Jun Lin
Keyword(s):  
Heat Exchanger ◽  
Heat Exchange ◽  
Heat Pump ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Ground Heat Exchanger ◽  
Pipe Length ◽  
Pump System ◽  
Heat Pump System ◽  
Heating And Cooling

A hot-water and air-conditioning (HWAC) combined ground sourse heat pump(GSHP) system with horizontal ground heat exchanger self-designed and actualized was presented in this paper. The heat transfer performance for the heat exchanger of two different pipe arrangements, three layers and four layers, respectively, was compared. It showed that the heat exchange quantity per pipe length for the pipe arrangement of three layers and four layers are 18.0 W/m and 15.0 W/m. The coefficient of performance (COP) of unit and system could remain 4.8 and 4.2 as GSHP system for heating water, and the COP of heating and cooling combination are up to 8.5 and 7.5, respectively. The power consumption of hot-water in a whole year is 9.0 kwh/t. The economy and feasibility analysis on vertical and horizontal ground heat exchanger were made, which showed that the investment cost per heat exchange quantity of horizontal ground heat exchanger is 51.4% lower than that of the vertical ground heat exchanger, but the occupied area of the former is 7 times larger than the latter's.

scholarly journals Frosting Phenomenon and Frost-Free Technology of Outdoor Air Heat Exchanger for an Air-Source Heat Pump System in China: An Analysis and Review

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2642 ◽  
Author(s):  
Yi Zhang ◽  
Guanmin Zhang ◽  
Aiqun Zhang ◽  
Yinhan Jin ◽  
Ruirui Ru ◽  
...  
Keyword(s):  
Heat Exchanger ◽  
Heat Pump ◽  
Operating Cost ◽  
Heating System ◽  
Coefficient Of Performance ◽  
Outdoor Air ◽  
Pump System ◽  
Heat Pump System ◽  
Reduce Operating Cost ◽  
Air Source Heat Pump

Frost layer on the outdoor air heat exchanger surface in an air-source heat pump (ASHP) can decrease the system coefficient of performance (COP). Although the common defrosting and anti-frosting methods can improve the COP, the periodic defrosting not only reduces the system energy efficiency but also deteriorates the indoor environment. To solve these problems, it is necessary to clearly understand the frosting phenomenon and to achieve the system frost-free operation. This paper focused firstly on the analyses of frosting pathways and frosting maps. Followed by summarizing the characteristics of frost-free technologies. And then the performances of two types of frost-free ASHP (FFASHP) systems were reviewed, and the exergy and economic analysis of a FFASHP heating system were carried out. Finally, the existing problems related to the FFASHP technologies were proposed. Results show that the existing frosting maps need to be further improved. The FFASHP systems can not only achieve continuous frost-free operation but reduce operating cost. And the total COP of the FFASHP heating system is approximately 30–64% higher than that of the conventional ASHP system under the same frosting conditions. However, the investment cost of the FFASHP system increases, and its reliability also needs further field test in a wider frosting environment. In the future, combined with a new frosting map, the control strategy for the FFASHP system should be optimized.

Sign in / Sign up

Export Citation Format

Share Document