Effect of Area Ratio on the Galvanic Corrosion of AZX611 Magnesium Alloy/A6N01 Aluminum Alloy Joint

In this work, the galvanic corrosion behavior of AZ31 magnesium alloy in contact with A6N01S-T5 aluminum alloy in NaCl solution was investigated by electrochemical method, the salt immersion method, SEM. And three protection techniques: (a) rubber gasket technique ,(b)organic coating technique and (c) anodizing technique were used to inhibit the galvanic corrosion. The results of open circuit potential and polarization curve method were explained the corrosion behavior of AZ31 and A6N01S-T5.It was found that AZ31 as anode was accelerated corrosion and A6N01S-T5 as cathode was also corrode in salt immersion experiment. With the increasing of immersion time, the corrosion rate of AZ31 and A6N01S-T5 was gradually decreasing. Then, the efficacy of different anti-corrosive technologies was compared. Fluorine coating technique was an effective way to protect Mg alloy and Al alloy. It was possible to guide the anti-corrosion of magnesium alloy in mobile industry.

Download Full-text

ALCOA ALUMINUM ALLOY 7050

Alloy Digest ◽

10.31399/asm.ad.al0233 ◽

1990 ◽

Vol 39 (1) ◽

Keyword(s):

Corrosion Resistance ◽

Aluminum Alloy ◽

High Temperature ◽

Magnesium Alloy ◽

Stress Corrosion Cracking ◽

Heat Treating ◽

Thin Sections ◽

Aerospace Applications ◽

Temperature Performance ◽

Aluminum Company

Abstract ALCOA ALUMINUM ALLOY 7050 is an aluminum-zinc-copper-magnesium alloy with a superior combination of strength, stress-corrosion cracking resistance and toughness, particularly in thick sections. In thin sections it also possesses an excellent combination of properties that are important for aerospace applications. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on low and high temperature performance, and corrosion resistance as well as forming, heat treating, and joining. Filing Code: Al-233. Producer or source: Aluminum Company of America. Originally published as Aluminum 7050, January 1979, revised January 1990.

Download Full-text

Effect of Laser Power on Microstructure and Micro-Galvanic Corrosion Behavior of a 6061-T6 Aluminum Alloy Welding Joints

Metals ◽

10.3390/met11010003 ◽

2020 ◽

Vol 11 (1) ◽

pp. 3

Author(s):

Huiling Zhou ◽

Fanglian Fu ◽

Zhixin Dai ◽

Yanxin Qiao ◽

Jian Chen ◽

...

Keyword(s):

Aluminum Alloy ◽

Laser Power ◽

Galvanic Corrosion ◽

Gas Metal Arc Welding ◽

Immersion Test ◽

Intermetallic Particles ◽

Metal Arc Welding ◽

Corrosion Behaviors ◽

Welding Joints ◽

Corrosion Pits

The 6061-T6 aluminum alloy welding joints were fabricated using gas metal arc welding (GMAW) of various laser powers, and the effect of laser power on the microstructure evolution of the welding joints was investigated. The corrosion behaviors of 6061-T6 aluminum alloy welding joints were investigated in 3.5 wt% NaCl solution using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). The results showed that the micro-galvanic corrosion initiation from Mg2Si or around the intermetallic particles (Al-Fe-Si) is observed after the immersion test due to the inhomogeneous nature of the microstructure. The preferential dissolution of the Mg2Si and Al-Fe-Si is believed to be the possible cause of pitting corrosion. When the laser power reached 5 kW, the microstructure of the welded joint mainly consisted of Al-Fe-Si rather than the Mg2Si at 2 kW. The relatively higher content of Al-Fe-Si with increasing in laser power would increase the volume of corrosion pits.

Download Full-text

Newly Developed Heat Resistant Magnesium Alloy by Thixomolding®

Materials Science Forum ◽

10.4028/www.scientific.net/msf.488-489.287 ◽

2005 ◽

Vol 488-489 ◽

pp. 287-290 ◽

Cited By ~ 1

Author(s):

Tadayoshi Tsukeda ◽

Ken Saito ◽

Mayumi Suzuki ◽

Junichi Koike ◽

Kouichi Maruyama

Keyword(s):

Aluminum Alloy ◽

Magnesium Alloy ◽

Magnesium Alloys ◽

Room Temperature ◽

Elevated Temperatures ◽

Die Casting ◽

The Other ◽

Heat Resistant ◽

Higher Temperature ◽

Better Than

We compared the newly developed heat resistant magnesium alloy with conventional ones by Thixomolding® and aluminum alloy by die casting. Tensile properties at elevated temperatures of AXEJ6310 were equal to those of ADC12. In particular, elongation tendency of AXEJ6310 at higher temperature was better than those of the other alloys. Creep resistance of AXEJ6310 was larger than that of AE42 by almost 3 orders and smaller than that of ADC12 by almost 2 orders of magnitude. Fatigue limits at room temperature and 423K of AXEJ6310 was superior among conventional magnesium alloys.

Download Full-text