Combined Effect of Gas Blow Induction Heating Nitriding and Post-Treatment with Fine Particle Peening on Surface Properties and Wear Resistance of Titanium Alloy

2021 ◽  
Author(s):  
Shogo Takesue ◽  
Shoichi Kikuchi ◽  
Yoshitaka Misaka ◽  
Tatsuro Morita ◽  
Jun Komotori
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Surface Properties ◽  
Induction Heating ◽  
Fine Particle ◽  
Post Treatment ◽  
Combined Effect

SURFACE PROPERTIES OF THE IN SITU FORMED CERAMICS REINFORCED COMPOSITE COATINGS ON TI-3AL-2V ALLOYS

2012 ◽  
Vol 19 (02) ◽  
pp. 1250009 ◽  
Author(s):  
PENG LIU ◽  
WEI GUO ◽  
DAKUI HU ◽  
HUI LUO ◽  
YUANBIN ZHANG
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Composite Coating ◽  
Surface Properties ◽  
Laser Cladding ◽  
Composite Coatings ◽  
Micro Hardness ◽  
Reinforced Composite

The synthesis of hard composite coating on titanium alloy by laser cladding of Al/Fe/Ni+C/Si3N4 pre-placed powders has been investigated in detail. SEM result indicated that a composite coating with metallurgical joint to the substrate was formed. XRD result indicated that the composite coating mainly consisted of γ- (Fe, Ni) , FeAl , Ti3Al , TiC , TiNi , TiC0.3N0.7 , Ti2N , SiC , Ti5Si3 and TiNi . Compared with Ti-3Al-2V substrate, an improvement of the micro-hardness and the wear resistance was observed for this composite coating.

Effect of cluster-gradient architecture of nanostructured topocomposites on features of tribointeraction with heterophased material

2020 ◽  
pp. 130-135
Author(s):  
D.N. Korotaev ◽  
K.N. Poleshchenko ◽  
E.N. Eremin ◽  
E.E. Tarasov
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Energy Dissipation ◽  
Phase Structure ◽  
Diffusion Processes ◽  
Structural Phase ◽  
High Wear Resistance ◽  
Wear Characteristics ◽  
And Diffusion

The wear resistance and wear characteristics of cluster-gradient architecture (CGA) nanostructured topocomposites are studied. The specifics of tribocontact interaction under microcutting conditions is considered. The reasons for retention of high wear resistance of this class of nanostructured topocomposites are studied. The mechanisms of energy dissipation from the tribocontact zone, due to the nanogeometry and the structural-phase structure of CGA topocomposites are analyzed. The role of triboactivated deformation and diffusion processes in providing increased wear resistance of carbide-based topocomposites is shown. They are tested under the conditions of blade processing of heat-resistant titanium alloy.

Influence of oxynitriding on the wear resistance of VT14 titanium alloy

2011 ◽  
Vol 46 (6) ◽  
pp. 834-840
Author(s):  
I. M. Pohrelyuk ◽  
O. V. Tkachuk ◽  
O. V. Sambors’kyi
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Vt14 Titanium Alloy ◽  
Vt14 Titanium

Effect of laser rescanning on Ti6Al4V microstructure during selective laser melting

2020 ◽  
pp. 095440542097609
Author(s):  
Weipeng Duan ◽  
Meiping Wu ◽  
Jitai Han
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Selective Laser Melting ◽  
Human Body ◽  
High Impact ◽  
Laser Melting ◽  
Heat Treated ◽  
Volume Porosity ◽  
Biomedical Field

TC4, which is one of the most widely used titanium alloy, is frequently used in biomedical field due to its biocompatible. In this work, selective laser melting (SLM) was used to manufacture TC4 parts and the printed parts were heat-treated using laser rescanning technology. The experimental results showed that laser rescanning had a high impact on the quality of SLMed part, and a different performance on wear resistance can be found on the basis. It can be seen that the volume porosity of the sample was 7.6 ± 0.5% without using any further processing technology. The volume porosity of the sample processed using laser rescanning strategy was decreased and the square-framed rescanning strategy had a relative optimal volume porosity (1.5 ± 0.3%) in all these five samples. With the further decreasing of volume porosity, the wear resistance decreased at the same time. As its excellent bio-tribological properties, the square-framed rescanning may be a potential suitable strategy to forming TC4 which used in human body.

PHYSICAL PROPERTIES AND MICROSTRUCTURE PERFORMANCE OF LASER ALLOYING Zn MODIFIED AMORPHOUS-NANOCRYSTALS REINFORCED COATING

NANO ◽  
2013 ◽  
Vol 08 (04) ◽  
pp. 1350038 ◽  
Author(s):  
JIANQUAN LI ◽  
HUASHI LIU ◽  
JIANING LI ◽  
GUOZHONG LI
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Electron Microscope ◽  
Crystallization Process ◽  
Laser Alloying ◽  
X Ray Diffraction ◽  
X Ray ◽  
Amorphous Phases ◽  
Transmission Electron ◽  
Improve Wear Resistance

Zn was firstly used to improve wear resistance of a TA7 (Ti–5Al–2.5Sn) titanium alloy surface by mean of a laser alloying (LA) technique. The synthesis of the hard coating on a TA7 titanium alloy by LA of Co–Ti–Cr–TiB2–Zn–CeO2 pre-placed powders was investigated by means of scanning electron microscope (SEM), X-ray diffraction (XRD) and high resolution transmission electron microscope (HRTEM). Experimental results indicated lot of the nanocrystals, such as Ti–B/CoZn13 and the amorphous phases were produced in such LA coating. The nucleation and growth of the amorphous phases were retarded by the nanocrystals in a certain extent during the crystallization process of the amorphous phases. Compared with a TA7 alloy substrate, an improvement of the wear resistance was obtained for such LA composite coating.

Fretting wear behavior of thermal-oxidation on titanium alloy in air and vacuum atmosphere

2021 ◽  
pp. 2150135
Author(s):  
Liangliang Sheng ◽  
Xiangtao Deng ◽  
Hao Li ◽  
Yuxuan Ren ◽  
Guoqing Gou ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Titanium Alloy ◽  
Thermal Oxidation ◽  
Wear Behavior ◽  
Fretting Wear ◽  
Partial Slip ◽  
Ti6al4v Titanium Alloy ◽  
Slip Regime ◽  
Air Atmosphere ◽  
Vacuum Atmosphere

In this work, an in-situ XPS analysis test combined self-designed high precision fretting wear tester was carried out to study the fretting wear behavior and the resulting tribo-oxidation of thermal-oxidation film on Ti6Al4V titanium alloy under the varied working atmosphere. The fretting-induced tribo-oxidation under the air and vacuum ([Formula: see text] Pa) environment was analyzed and its response on the resulting fretting wear resistance and damage mechanism was discussed. Results show that the working environment plays a significant role in the formation of tribo-oxidation and then determining the fretting wear resistance. Thermal-oxidation film in the vacuum atmosphere shows a better fretting wear resistance than that in the air atmosphere for all fretting regimes, except for partial slip regime (PSR) where there is an equivalent fretting wear resistance. Compared with the substrate Ti6Al4V titanium alloy, the thermal-oxidation film in the vacuum atmosphere performs a good protection for titanium alloy, especially for slip regime (SR), but not applied for air atmosphere.

Sign in / Sign up

Export Citation Format

Share Document