Comparative study of stainless steel AISI 431 coatings prepared by extreme-high-speed and conventional laser cladding

2019 ◽  
Vol 31 (4) ◽  
pp. 042009 ◽  
Author(s):  
Liqun Li ◽  
Faming Shen ◽  
Yuandong Zhou ◽  
Wang Tao
Keyword(s):  
Stainless Steel ◽  
Comparative Study ◽  
Laser Cladding ◽  
High Speed ◽  
Steel Aisi ◽  
Stainless Steel Aisi ◽  
Conventional Laser

AL TECH MIAMI

Alloy Digest ◽  
1983 ◽  
Vol 32 (11) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Heat Treating ◽  
Good Resistance ◽  
Aisi Type ◽  
Steel Aisi ◽  
Resistance To Wear ◽  
Specialty Steel ◽  
Stainless Steel Aisi ◽  
Plastic Mold

Abstract AL TECH MIAMI is both a hardenable stainless steel (AISI Type 420) and a tool steel for making molds for plastic. A major requirement for plastic mold steel is corrosion resistance. Certain plastics, such as poly-vinyl chlorides, are very corrosive and stored molds often rust from sweating water lines and/or humid environments. AL TECH MIAMI has good resistance to wear. It is melted and AOD refined to assure the mold-maker of cleanliness and freedom from internal imperfections. It provides exceptionally good polishability for lens-quality molds. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and machining. Filing Code: SS-435. Producer or source: AL Tech Specialty Steel Corporation.

scholarly journals Influence of Activated Fluxes on the Bead Shape of A-TIG Welds on Carbon and Low-Alloy Steels in Comparison with Stainless Steel AISI 304L

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 530
Author(s):  
Jerzy Niagaj
Keyword(s):  
Stainless Steel ◽  
Penetration Depth ◽  
High Strength ◽  
Tig Welding ◽  
Low Alloy Steels ◽  
Aisi 304L ◽  
A Tig Welding ◽  
Alloy Steels ◽  
Steel Aisi ◽  
Stainless Steel Aisi

The article presents results of comparative A-TIG welding tests involving selected unalloyed and fine-grained steels, as well as high-strength steel WELDOX 1300 and austenitic stainless steel AISI 304L. The tests involved the use of single ingredient activated fluxes (Cr2O3, TiO2, SiO2, Fe2O3, NaF, and AlF3). In cases of carbon and low-alloy steels, the tests revealed that the greatest increase in penetration depth was observed in the steels which had been well deoxidized and purified during their production in steelworks. The tests revealed that among the activated fluxes, the TiO2 and SiO2 oxides always led to an increase in penetration depth during A-TIG welding, regardless of the type and grade of steel. The degree of the aforesaid increase was restricted within the range of 30% to more than 200%.

Phase Studies in WC-Stainless Steel AISI 347 Hardmetal System with Graphite Addition

2014 ◽  
Vol 1024 ◽  
pp. 239-242
Author(s):  
Zuhailawati Hussain ◽  
Emee Marina Salleh ◽  
Tran Bao Trung ◽  
Zainal Arifin Ahmad
Keyword(s):  
Stainless Steel ◽  
Powder Mixture ◽  
Milled Powder ◽  
Graphite Powder ◽  
Planetary Mill ◽  
Argon Atmosphere ◽  
Maximum Hardness ◽  
Steel Container ◽  
Steel Aisi ◽  
Stainless Steel Aisi

In this study, WC-stainless steel AISI 347 hardmetal system was produced to replace WC-Co hardmetal which uses the expensive, toxic and depleted resource Co. WC, stainless steel AISI 347 and graphite powder mixture were milled in a planetary mill under argon atmosphere using a stainless steel container and balls. Carbon was added in amounts ranging from 0 wt% until 4 wt% into the composition to avoid unwanted η (Fe3W3C) phase. As-milled powder was compacted at 300 MPa and sintered in a tube furnace at 1350°C. ɳ phase was detected in compositions with 0 and 1 wt% C addition. For 2 wt% C addition, no η (Fe3W3C) phase formation was identified. However, the η phase was detected for compositions containing 3 and 4 wt% C. Maximum hardness was achieved due to the absence of η phase.

Residual Stress Analysis in Deep Rolling Process on Gas Tungsten Arc Weld of Stainless Steel AISI 316L

2021 ◽  
Vol 880 ◽  
pp. 23-28
Author(s):  
Warinthorn Thanakulwattana ◽  
Wasawat Nakkiew
Keyword(s):  
Residual Stress ◽  
Stainless Steel ◽  
Surface Layer ◽  
Compressive Residual Stress ◽  
Aisi 316L ◽  
Deep Rolling ◽  
Gas Tungsten Arc ◽  
Steel Aisi ◽  
Gas Tungsten ◽  
Stainless Steel Aisi

Because of the general problem of the welding workpiece such as fatigue fracture caused by tensile residual stress lead to initial and propagation crack in the fusion zone. Thus, the mechanical surface treatment of deep rolling on Gas Tungsten Arc Welded (GTAW) surfaces of AISI 316L was studied. Deep rolling (DR) is a cold working process to induce compressive residual stress in the surface layer of the workpiece resulting in hardening deformation which increased surface hardness, and smooth surface that inhibit crack growth and improve fracture strength of materials. The present study focuses on compressive residual stress at the surface of stainless steel AISI 316L butt welded joint of GTAW. The three parameters of DR process were used; pressure 150 bar, rolling speed 400 mm/min, and step over 1.0 mm. The residual stresses analysis by X-ray diffraction with sin2Ψ method at 0, 5, 10, and 20 mm from the center of the welded bead. The results showed that the DR process on the welded of GTAW induce the minimum compressive residual stress-408.6 MPa and maximum-498.1 MPa in longitudinal direction. The results of transverse residual stress in minimum and maximum are 43.7 MPa and-34.8 MPa respectively. The FWHM of DR both longitudinal and transverse direction were increased in the same trend. Furthermore, the microhardness after DR treatment on workpiece surface layer higher than GTAW average 0.4 times.

Characterisation of porosity, density, and microstructure of directed energy deposited stainless steel AISI 316L

2019 ◽  
Vol 25 ◽  
pp. 286-296 ◽  
Author(s):  
Zhi’En Eddie Tan ◽  
John Hock Lye Pang ◽  
Jacek Kaminski ◽  
Helene Pepin
Keyword(s):  
Stainless Steel ◽  
Aisi 316L ◽  
Steel Aisi ◽  
Directed Energy ◽  
Stainless Steel Aisi

Plasma-Assisted Nitriding in Low-Frequency Inductively Coupled Plasma Enhanced with Ferromagnetic Cores

2018 ◽  
Vol 37 (6) ◽  
pp. 545-550
Author(s):  
Mikhail Isupov ◽  
Vadim Pinaev ◽  
Daria Mul ◽  
Natalia Belousova
Keyword(s):  
Inductively Coupled Plasma ◽  
High Speed ◽  
Low Frequency ◽  
Sample Surface ◽  
Ion Energy ◽  
Inductively Coupled ◽  
Steel Aisi ◽  
Current Densities ◽  
Aisi 321 ◽  
Stainless Steel Aisi

AbstractAn experimental investigation of plasma-assisted nitriding of austenitic stainless steel AISI 321 in a low-pressure (7 Pa), low-frequency (50–100 kHz) nitrogen inductively coupled plasma enhanced with ferromagnetic cores has been performed at the temperatures of 470–625 °C, sample biases of ‒500–‒750 V, current densities on the sample surface of 1.2–3.3 mA/cm2 and nitriding times of 20 and 60 min. It is found that even the short (20 min) ion-plasma treatment results in the formation of nitrided layers with the thickness of up to 40 μm and microhardness of up to 9 GPa.The high speed of nitriding can be explained as a result of the joint action of high ion flux density and high ion energy on the sample surface.

Sign in / Sign up

Export Citation Format

Share Document