scholarly journals Study The Effect of Process Parameters of CNC Milling Surface Generation Using Al-alloy 7024

2019 ◽  
Vol 12 (3) ◽  
pp. 103-112
Author(s):  
Nareen Hafidh Obaeed
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Surface Finish ◽  
Feed Rate ◽  
Spindle Speed ◽  
Surface Generation ◽  
Depth Of Cut ◽  
Al Alloy ◽  
Cnc Milling ◽  
Tool Diameter

A wonderful unique research developments in modeling surface roughness and optimization of the predominant parameters to get a surface finish of desired level since only suitable selection of cutting parameters can get a better surface finish, so the objective of this work is to study the milling process parameters which include tool diameter, feed rate, spindle speed, and depth of cut resulting in optimal values of the surface roughness during machining AL-alloy 7024. The machining operation implemented on XK7124 3-axis CNC milling machine. The effects of the selected parameters on the chosen characteristics have been accomplished using Taguchi’s parameter design approach. The parameters considered are – depth of cut with two levels (0.2, 0.5 mm), tool diameter with two levels (6, 8 mm), spindle speed with two levels (1000, 2500 rpm), and finally feed rate with two levels (200, 500 mm/min). Analysis of the results showed that the optimal settings for low values of surface roughness are large tool diameter (8 mm), high spindle speed (2500 r.p.m), low feed rate (200 mm/min) and high depth of cut (0.5 mm). Response Table for mean of surface roughness showed that tool diameter has the most effected factors (rank one) followed by feed rate (rank two) then depth of cut which is the third effected factors and finally spindle speed with the less effected factors of surface roughness (rank four).

scholarly journals The influence of machining parameters on surface roughness of MDF in milling operation

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 3266-3277
Author(s):  
Ümmü K. İşleyen ◽  
Mehmet Karamanoğlu
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Medium Density Fiberboard ◽  
Spindle Speed ◽  
Numerical Control ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Milling Operation ◽  
Four Levels ◽  
Tool Diameter

This paper examined the effect of machining parameters on surface roughness of medium density fiberboard (MDF) machined using a computer numerical control (CNC) router. The machining parameters such as spindle speed, feed rate, depth of cut, and tool diameter were examined for milling. The experiments were conducted at two levels of spindle speeds, four levels of feed rates, two levels of tool diameters, and two levels of axial depths of cut. The surface roughness values of MDF grooved by CNC were measured with stylus-type equipment. Statistical methods were used to determine the effectiveness of the machining parameters on surface roughness. The influence of each milling parameter affecting surface roughness was analyzed using analysis of variance (ANOVA). The significant machining parameters affecting the surface roughness were the feed rate, spindle speed, and tool diameter (p < 0.05). There was no significant influence of axial depth of cut on the surface roughness. The surface roughness decreased with increasing spindle speed and decreasing feed rate. The value of surface roughness increased with the increase of tool diameter.

scholarly journals Sustainable Manufacturing and Parametric Analysis of Mild Steel Grade 60 by Deploying CNC Milling Machine and Taguchi Method

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1303
Author(s):  
Shakir Azim ◽  
Sahar Noor ◽  
Qazi Salman Khalid ◽  
Aqib Mashood Khan ◽  
Danil Yurievich Pimenov ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Mild Steel ◽  
Feed Rate ◽  
Sustainable Manufacturing ◽  
Steel Grade ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Milling Machine ◽  
Cnc Milling ◽  
Cnc Milling Machine

Design and manufacturing are the key steps in the sustainable manufacturing of any product to be produced. Within the perspective of injection molds production, increased competitiveness and repeated changes in the design require a complete optimized manufacturing process. Local and minor improvements in the milling process do not generally lead to an optimized manufacturing process. The goal of the new geometry and parametric analysis of the mould is to reduce the quality issues in mild steel grade 60. In this explicit research, the surface roughness (smoothness) of indigenously produced injection moulds in the local market in Pakistan is investigated. The CNC milling machine (five-axis) is used for the manufacturing of an injection mould, and the Taguchi method of the design of the experiment is applied for parameters optimization. Hence, the overall process is assisted in balancing the milling machine parameters to trim down the surface roughness issue in mild steel moulds and increase their sustainability. The spindle speed (rpm), the depth of cut (mm), and the feed rate (mm/rev) are considered as input variables for process optimization, and the experiments are performed on mild steel grade 60. It is deduced that the combination of a spindle speed of 800 rpm, feed rate of 10 mm/rev and depth of cut of 0.5 mm is the best case in case of minimum surface roughness, which leads to sustainable products. It is also deduced from ANOVA, that the spindle speed is a factor that affects the surface roughness of mild steel products, while the feed rate turns out to be insignificant.

Rapid and Versatile Micromold Fabrication Using Micromilling and Nanopolishing for Microfluidic Devices

2019 ◽  
Author(s):  
Thanh-Qua Nguyen ◽  
Jeongmin Mah ◽  
Woo-Tae Park ◽  
Sangyoup Lee
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
High Surface ◽  
Spindle Speed ◽  
Numerical Control ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Cnc Milling ◽  
Tool Marks ◽  
Mold Fabrication

Abstract In an effort to make microfluidic research more attractive and cost-effective, micromilled polymethyl methacrylate (PMMA) has gained interests as an alternative method to the conventional cleanroom-based micromolds fabrication technologies. The most enabling aspects of micromilling are flexibility on the design changes and the ability to fabricate three-dimensional structures. However, the major drawback of micromilling based micromold fabrication is the presence of burrs and tool marks on the surface after machining. High surface roughness on replicated polymer results in poor bonding strength and optical clarity. The roughness of micromilled surface strongly depends on the machining parameters such as tool size, spindle speed, feed rate, width of cut, and depth of cut. Thus, it is crucial to optimize the machining parameters to obtain a good surface finish. Although the optimal fabrication parameters are used to machine the micromold, the surface roughness of micromilled mold is still relative high compared to the surface of unprocessed PMMA. In this paper, we first optimize the micromilling parameters of Computer Numerical Control (CNC) milling machine to achieve the best possible of surface roughness. We have optimized the machining parameters for a flat endmill with 100 μm, 200 μm, and 400 μm in diameter of spindle speed, feed rate, width of cut, and the depth of cut respectively at 18000 rpm, 20 mm/min, 30 μm, and 20 μm. Then, a method to polish the structured surface of the micromilled mold was developed using the rotary magnetic field. By modifying the CNC program language G-code, we were able to control the polishing path, polishing force and time precisely. Consequently, the burrs and tool marks are completely removed, such that the roughness of the surface is decreased from 350 nm Ra to 30 nm Ra, and 1200 nm Rz to 300 nm Rz while the profile of microstructures is not deteriorated. Finally, we demonstrate our mold fabrication scheme by building a microfluidic immunoassay device with four Quake’s valves and showed the sequential assay process successfully.

scholarly journals OPTIMIZATION OF VARIABEL HELIX ANGLE PARAMETERS IN CNC MILLING OF CHATTER AND SURFACE ROUGHNES USING TAGUCHI METHOD

2021 ◽  
Vol 9 (1) ◽  
pp. 35-44
Author(s):  
Festo Andre Hardinsi ◽  
◽  
Oyong Novareza ◽  
Achmad As'ad Sonief
Keyword(s):  
Surface Roughness ◽  
Taguchi Method ◽  
Feed Rate ◽  
Helix Angle ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Cnc Milling ◽  
Excited Vibration ◽  
Optimal Value ◽  
Variable Helix

In the manufacturing industries, the main problem in process of operating CNC milling machine was chatter effect (self-excited vibration) which increases the quality of the surface roughness. In this study is to determine optimal value of parameters for chatter and surface roughness. The chatter measured using accelerometer MPU-6050 with Arduino by software LabVIEW-2019 based on peaks-FFT value and the surface roughness measured by SJ-301 tester. The research parameters like variable helix angle, spindle speed, feed rate, and depth of cut using stainless steel 304 by Taguchi method. The optimum parameters value obtained are variable helix 35/38 degrees, spindle speed 3000 RPM, feed rate 150 mm/min and depth of cut 0.4 mm. Based on ANOVA value, the variable helix angle and depth of cut are found to be significant for chatter and surface roughness. The depth of cut was high contribution by ANOVA chatter by 93.84% and surface roughness by 91.93%.

scholarly journals Effect of Turning Parameters and Reinforcement on the Surface Roughness of Hybrid Aluminium Metal Matrix Composite

2019 ◽  
Vol 9 (1) ◽  
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Matrix Material ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Pure Aluminium ◽  
Machining Time

Since last two decades, technology has changed rapidly in each industry from consumer goods to aerospace. To quench the thrust of technology advancement of industries, the research community has to develop the novel materials. As a part of the ongoing process of material development and machinability study, present work was carried out to find out the effect of various cutting parameters on surface roughness and machining time of aluminium Hybrid Metal Matrix Composites (AHMMCs). In this study, pure aluminium was used as a matrix material while; B4C, Mg, Ti and Graphite were used as reinforcement. It was observed that 2202 RPM spindle speed, 0.18 mm/rev feed rate and 1.1 mm depth of cut are the optimum turning parameters with PCD insert. While machining of same composites using carbide insert, optimum spindle speed, feed rate and depth of cut are 2091 RPM, 0.19 mm/rev and 1.1 mm respectively. Moreover, PCD insert provides better surface finish compared to carbide coated insert for same cutting conditions. Moreover, the effect of reinforcement particles presence on the surface finish was also investigated and it was concluded that reinforcement presence reduces the surface roughness considerably. Particularly presence of Mg and graphite reduces surface finish significantly.

Prediction of Surface Roughness and Optimization of Cutting Parameters in CNC Turning of Rotational Features

2020 ◽  
Vol 38 (8A) ◽  
pp. 1143-1153
Author(s):  
Yousif K. Shounia ◽  
Tahseen F. Abbas ◽  
Raed R. Shwaish
Keyword(s):  
Surface Roughness ◽  
Linear Regression ◽  
Regression Model ◽  
Linear Regression Model ◽  
Feed Rate ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Non Linear ◽  
Optimization Of Cutting Parameters

This research presents a model for prediction surface roughness in terms of process parameters in turning aluminum alloy 1200. The geometry to be machined has four rotational features: straight, taper, convex and concave, while a design of experiments was created through the Taguchi L25 orthogonal array experiments in minitab17 three factors with five Levels depth of cut (0.04, 0.06, 0.08, 0.10 and 0.12) mm, spindle speed (1200, 1400, 1600, 1800 and 2000) r.p.m and feed rate (60, 70, 80, 90 and 100) mm/min. A multiple non-linear regression model has been used which is a set of statistical extrapolation processes to estimate the relationships input variables and output which the surface roughness which prediction outside the range of the data. According to the non-linear regression model, the optimum surface roughness can be obtained at 1800 rpm of spindle speed, feed-rate of 80 mm/min and depth of cut 0.04 mm then the best surface roughness comes out to be 0.04 μm at tapper feature at depth of cut 0.01 mm and same spindle speed and feed rate pervious which gives the error of 3.23% at evolution equation.

Effects of Insert Nose Radius and Processing Cutting Parameter on the Surface Roughness of Aisi 316 Stainless Steel

2010 ◽  
Vol 447-448 ◽  
pp. 51-54
Author(s):  
Mohd Fazuri Abdullah ◽  
Muhammad Ilman Hakimi Chua Abdullah ◽  
Abu Bakar Sulong ◽  
Jaharah A. Ghani
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Finish ◽  
Feed Rate ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 316

The effects of different cutting parameters, insert nose radius, cutting speed and feed rates on the surface quality of the stainless steel to be use in medical application. Stainless steel AISI 316 had been machined with three different nose radiuses (0.4 mm 0.8 mm, and 1.2mm), three different cutting speeds (100, 130, 170 m/min) and feed rates (0.1, 0.125, 0.16 mm/rev) while depth of cut keep constant at (0.4 mm). It is seen that the insert nose radius, feed rates, and cutting speed have different effect on the surface roughness. The minimum average surface roughness (0.225µm) has been measured using the nose radius insert (1.2 mm) at lowest feed rate (0.1 mm/rev). The highest surface roughness (1.838µm) has been measured with nose radius insert (0.4 mm) at highest feed rate (0.16 mm/rev). The analysis of ANOVA showed the cutting speed is not dominant in processing for the fine surface finish compared with feed rate and nose radius. Conclusion, surface roughness is decreasing with decreasing of the feed rate. High nose radius produce better surface finish than small nose radius because of the maximum uncut chip thickness decreases with increase of nose radius.

Investigation of Surface Roughness and Material Removal Rate for High Speed Micro End Milling on PMMA

2015 ◽  
Vol 1115 ◽  
pp. 12-15
Author(s):  
Nur Atiqah ◽  
Mohammad Yeakub Ali ◽  
Abdul Rahman Mohamed ◽  
Md. Sazzad Hossein Chowdhury
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
High Speed ◽  
End Milling ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Micro End Milling

Micro end milling is one of the most important micromachining process and widely used for producing miniaturized components with high accuracy and surface finish. This paper present the influence of three micro end milling process parameters; spindle speed, feed rate, and depth of cut on surface roughness (Ra) and material removal rate (MRR). The machining was performed using multi-process micro machine tools (DT-110 Mikrotools Inc., Singapore) with poly methyl methacrylate (PMMA) as the workpiece and tungsten carbide as its tool. To develop the mathematical model for the responses in high speed micro end milling machining, Taguchi design has been used to design the experiment by using the orthogonal array of three levels L18 (21×37). The developed models were used for multiple response optimizations by desirability function approach to obtain minimum Ra and maximum MRR. The optimized values of Ra and MRR were 128.24 nm, and 0.0463 mg/min, respectively obtained at spindle speed of 30000 rpm, feed rate of 2.65 mm/min, and depth of cut of 40 μm. The analysis of variance revealed that spindle speeds are the most influential parameters on Ra. The optimization of MRR is mostly influence by feed rate. Keywords:Micromilling,surfaceroughness,MRR,PMMA

scholarly journals Penerapan Metode Taguchi untuk Optimasi Setting Parameter CNC Milling Terhadap Kekasaran Permukaan Material

2020 ◽  
Vol 2 (2) ◽  
pp. 49-60
Author(s):  
Farizi Rachman Farizi Rachman ◽  
Bayu Wiro K ◽  
Tri Andi Setiawan ◽  
Pradita Nurkholies
Keyword(s):  
Feed Rate ◽  
Base Plate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Cnc Milling ◽  
End Mill

Industri manufaktur di Indonesia semakin meningkat seiring dengan tingkat kebutuhan manusia yang beraneka ragam dan memicu berkembangnya teknologi, salah satunya industri proses permesinan atau machining. Kualitas produk yang baik dapat dilihat dari tingkat kekasaran permukaannya karena kekasaran permukaan dapat mempengaruhi performa yang berkaitan dengan aspek fungsional dari produk. Pada penelitian ini telah dilakukan optimasi setting parameter CNC milling terhadap kekasaran permukaan pada material S50C dengan end mill HSS diameter 8 mm. Material S50C banyak digunakan dalam manufaktur mesin seperti mekanis base plate, roda gigi, standart punch head dan komponen mesin lainnya. Penelitian ini menggunakan metode Taguchi. Parameter yang digunakan yaitu spindle speed, Feed rate dan depth of cut dengan cairan pendingin sebagai variabel konstan. Parameter optimum untuk mendapatkan nillai kekasaran yang rendah yaitu spindle speed 1100 rpm, feed rate 46 mm/min dan depth of cut 0.5 mm. Dengan taraf signifikansi 0.1 menunjukkan bahwa spindle speed berpengaruh secara signifikan dengan kontribusi 38.42% diikuti feed rate dengan kontribusi 34.16%.

scholarly journals Optimization of Boring Process Parameters in Manufacturing of Polyacetal Bushing using High Speed Steel

2019 ◽  
Vol 130 ◽  
pp. 01031 ◽  
Author(s):  
The Jaya Suteja ◽  
Yon Haryono ◽  
Andri Harianto ◽  
Esti Rinawiyanti
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Feed Rate ◽  
High Speed ◽  
Removal Rate ◽  
High Speed Steel ◽  
Cutting Edge ◽  
Depth Of Cut ◽  
Optimum Result ◽  
Edge Angle

Polyacetal is commonly used as bushing material because of its low coefficient of friction and self lubricant characteristics. The polyacetal is machined by using boring process to produce bushing in certain surface roughness. The objectives of this research are to optimize three independent parameters (depth of cut, feed rate and principal cutting edge angle) of boring process of polyacetal using high speed steel tool to achieve the highest material removal rate and the required surface roughness. Response Surface Methodology is used to investigate the influence of the parameters and optimize the boring process. The research shows that the influence of the boring process parameters on polyacetal is similar compared to on metal. The result reveals that the optimum result is achieved by applying the value of depth of cut, feed rate, and principal cutting edge angle is 2.9 × 10–3 m, 0.229 mm rev–1, and 99.1° respectively. By applying these values, the maximum material rate removal achieved in this research is 1263.4 mm3 s–1 and the surface roughness achieved is 1.57 × 10–6 m.

Sign in / Sign up

Export Citation Format

Share Document