scholarly journals Taking into Account Outer Hydrodynamic Pressure in Differential Equation of Variable Flow Rate Fluid Flow for Distributive Pressure Pipelines

2012 ◽  
Vol 7 (1) ◽  
pp. 13-22
Author(s):  
Volodymyr V. Cherniuk
Keyword(s):  
Differential Equation ◽  
Fluid Flow ◽  
Flow Rate ◽  
Hydrodynamic Pressure ◽  
Variable Flow

Abstract In the differential equation of variable flow rate fluid flow a component which takes into account outer hydrodynamic pressure is introduced. The variables of the equation are expressed in terms of full operating head and in terms of independent distance along the axis of the stream, i. e. this equation is reduced to a singlevariable equation.

Application of Cross-correlation Analysis Method for Measurement of the Fluid Flow Rate Based on X-ray Radiation

2019 ◽  
Vol 11 (1) ◽  
pp. 01025-1-01025-5 ◽  
Author(s):  
N. A. Borodulya ◽  
◽  
R. O. Rezaev ◽  
S. G. Chistyakov ◽  
E. I. Smirnova ◽  
...  
Keyword(s):  
Fluid Flow ◽  
Correlation Analysis ◽  
Flow Rate ◽  
Cross Correlation ◽  
Fluid Flow Rate ◽  
Analysis Method ◽  
X Ray ◽  
Cross Correlation Analysis ◽  
Correlation Analysis Method

Study of fluid flow through a channel deformed by piezoelement

2018 ◽  
Vol 13 (3) ◽  
pp. 1-10 ◽  
Author(s):  
I.Sh. Nasibullayev ◽  
E.Sh Nasibullaeva ◽  
O.V. Darintsev
Keyword(s):  
Fluid Flow ◽  
Pressure Drop ◽  
Boundary Conditions ◽  
Flow Rate ◽  
Contact Surface ◽  
Piezoelectric Element ◽  
Neumann Boundary ◽  
Differential Pressure ◽  
Physical Parameters ◽  
Flow Through

The flow of a liquid through a tube deformed by a piezoelectric cell under a harmonic law is studied in this paper. Linear deformations are compared for the Dirichlet and Neumann boundary conditions on the contact surface of the tube and piezoelectric element. The flow of fluid through a deformed channel for two flow regimes is investigated: in a tube with one closed end due to deformation of the tube; for a tube with two open ends due to deformation of the tube and the differential pressure applied to the channel. The flow rate of the liquid is calculated as a function of the frequency of the deformations, the pressure drop and the physical parameters of the liquid.

Flow Features Analysis of Throttle Notches of Proportional Direct Valve

2011 ◽  
Vol 189-193 ◽  
pp. 2285-2288
Author(s):  
Wen Hua Jia ◽  
Chen Bo Yin ◽  
Guo Jin Jiang
Keyword(s):  
Fluid Flow ◽  
Dynamic Behavior ◽  
Flow Rate ◽  
Discharge Coefficient ◽  
3D Models ◽  
Operating Conditions ◽  
Flow Models ◽  
Flow Features ◽  
Rate Discharge ◽  
Spool Valve

Flow features, specially, flow rate, discharge coefficient and efflux angle under different operating conditions are numerically simulated, and the effects of shapes and the number of notches on them are analyzed. To simulate flow features, 3D models are developed as commercially available fluid flow models. Most construction machineries in different conditions require different actions. Thus, in order to be capable of different actions and exhibit good dynamic behavior, flow features should be achieved in designing an optimized proportional directional spool valve.

Measurement of Osteocyte Deformation Resulting From Fluid Flow Induced Shear Stress

1999 ◽  
Author(s):  
Daniel P. Nicolella ◽  
Eugene Sprague ◽  
Lynda Bonewald
Keyword(s):  
Shear Stress ◽  
Fluid Flow ◽  
Flow Rate ◽  
Bone Cells ◽  
Individual Cell ◽  
Analysis Techniques ◽  
Sheer Stress ◽  
Increased Sensitivity ◽  
Cell Strains ◽  
Substrate Strain

Abstract It has been shown that bone cells are more responsive to fluid flow induced shear stress as compared to applied substrate strain (Owan, et al., 1997, Smalt, et al., 1997). Using novel micromechanical analysis techniques, we have measured individual cell strains resulting from 10 minutes of continuous fluid flow at a flow rate that produces a shear stress of 15 dyne/cm2. Individual cell strains varied widely from less than 1.0% to over 25% strain within the same group of cells. The increased sensitivity of cells to fluid flow induced shear stress may be attributed to much greater cellular deformations resulting from fluid flow induced sheer stress.

A Suction Device Using Air Under Pressure

1956 ◽  
Vol 23 (2) ◽  
pp. 269-272
Author(s):  
L. F. Welanetz
Keyword(s):  
Fluid Flow ◽  
Flow Rate ◽  
Fluid Flows ◽  
Central Hole ◽  
Fluid Flow Rate ◽  
Circular Plates ◽  
Suction Device ◽  
Holding Power ◽  
Plate Separation

Abstract An analysis is made of the suction holding power of a device in which a fluid flows radially outward from a central hole between two parallel circular plates. The holding power and the fluid flow rate are determined as functions of the plate separation. The effect of changing the proportions of the device is investigated. Experiments were made to check the analysis.

The Optimum Groove Geometry for Spiral Groove Viscous Pumps

1990 ◽  
Vol 112 (2) ◽  
pp. 409-414 ◽  
Author(s):  
Yuichi Sato ◽  
Kyosuke Ono ◽  
Akihiko Iwama
Keyword(s):  
Differential Equation ◽  
Flow Rate ◽  
Groove Width ◽  
Design Parameters ◽  
Width Ratio ◽  
Maximum Pressure ◽  
Spiral Groove ◽  
Clearance Ratio ◽  
Viscous Pump ◽  
Outflow Rate

The optimum geometries of disk and cylindrical sprial groove viscous pumps to provide the maximum pressure or flow rate are investigated theoretically. The geometrical design parameters, such as the groove angle, groove to ridge clearance ratio, groove width ratio and ridge clearance ratio, are considered as functions of meridional coordinate. Results are obtained from the solution of a differential equation for the smoothed overall pressure distribution of a spiral groove viscous pump. It is found that outflow rate increases with the increase of groove to ridge clearance ratio λ, and that for each value of λ there exist “optimum” values of groove angle and groove width ratio, which give a maximum outflow rate. However, the increase of λ decreases the ridge clearance.

Sign in / Sign up

Export Citation Format

Share Document