scholarly journals Flash Sintering of Commercial Zirconium Nitride Powders

2021 ◽  
Author(s):  
Diego Dubois ◽  
Amirali Eskandariyun ◽  
Suprabha Das ◽  
Andriy Durygin ◽  
Zhe Cheng

Flash sintering is an electrical field-assisted densification technique that requires passing a current through a ceramic powder compact. Pressure-assisted flash sintering of commercially available Zirconium Nitride (ZrN) powders has been demonstrated. Near fully dense samples can be obtained within a short period of time. The influences of parameters such as electrical field strength, voltage ramping rate, current limit, external pressure, pre-heating, and holding time on the onset of the flash event were investigated. Some post-flash sintered samples were subjected to the same condition to observe if the material would experience repeated flash. In addition, material properties such as density and hardness were measured and correlated with SEM and XRD. Implications of the observations on underlying flash sintering mechanism will also be discussed.

2017 ◽  
Vol 10 (1) ◽  
Author(s):  
N. Othman ◽  
A. Ahmad ◽  
M. A. Piramali

Demulsification is one of the key processes in emulsion liquid membrane application. This study involved the effect of electrical field on demulsification of water in oil using batch high voltage demulsifier system. This technique widely used because of its advantages of easy manipulation of applied field direction and strength, offers cost–effective separation and minimal environmental impact combined with mechanical simplicity. Influence of various values of frequency (400–1500 Hz) and voltage was studied experimentally using Alternate Current (AC) High Voltage Demulsifier with insulated electrode. The emulsion consists of kerosene as organic phase, sulfuric acid as internal phase and span 80 (3 and 5 w/v %) as a surfactant. The effect of emulsion preparation such as homogenizer speed, internal phase and surfactant concentrations on the stability of water–in–oil emulsion was also investigated. The results showed that the attractive forces between the water droplets under an electrical field increase by raising the applied electrical field strength. Meanwhile, the time required for the emulsion to separate and coalescence under electrical field increased when the stability of emulsion increased.


Records have been obtained of fluctuations in the speed of the tidal current in the Mersey estuary, using a current meter in a stand on the bottom, and compared with other records taken with the meter suspended freely at various depths. The fluctuations covered a wide range of periods but could be separated into two main types: ‘short period’, having periods of the order of a few seconds, and ‘long period’, with periods from 30 sec. to several minutes. The amplitudes, periods and auto-correlation of the short-period fluctuations have been examined in some detail, and it is concluded that the fluctuations observed near the bottom are evidence of the turbulence associated with bottom friction. It is believed to be the first time that the presence of turbulent velocity fluctuations of this time-scale in the sea has been established experimentally. The long-period fluctuations resemble those found in previous investigations and show features consistent with their being turbulent in origin also, although turbulence of the time-scale involved in their case would probably be mainly horizontal.


2013 ◽  
Vol 562-565 ◽  
pp. 1155-1160
Author(s):  
Yi Hong Lin ◽  
Guang Qi He ◽  
Hai Yan Liu ◽  
Jin Wei ◽  
Jian Yi Zheng ◽  
...  

Stability jet ejection and precision deposition are the two keys for industrial application of electrohydrodynamic printing. In this paper, inserted conductive probe is utilized to gain stability jet, which would increase the electrical field strength, reduce the back flow, onset and sustaining voltage. Lower applied voltage would enhance the stability of electrospun jet, in which fine jet can be used to direct-write orderly Micro/Nano-structure. With the guidance and constrain of inserted probe, the oscillating angle range of electrohydrodynamic jet is decreased to 3°from 15°, and the width of printed structures is 21μm in average that is much narrower than that printed from spinneret without probe (74μm in average). Spinneret with tip provides a good way to improve the control level of electrohydrodynamic printing, which would accelerate the industrial application of electrohydrodynamic printed Micro/Nano structure.


Author(s):  
Ram P. Bharti ◽  
Dalton J. E. Harvie ◽  
Malcolm R. Davidson

Pressure drop and electroviscous effects in the axisymmetric, steady, fully developed, pressure-driven flow of incompressible power-law fluids through a cylindrical microchannel at low Reynolds number (Re = 0.01) have been investigated. The Poisson-Boltzmann equation (describing the electrical potential) and the momentum equations in conjunction with electrical force and power-law fluid rheology have been solved numerically using the finite difference method. The pipe wall is considered to have uniform surface charge density (S = 4) and the liquid is assumed to be a symmetric electrolyte solution. In particular, the influence of the dimensionless inverse Debye length (K = 2, 20) and power-law flow behaviour index (n = 0.2, 1, 1.8) on the EDL potential, ion concentrations and charge density profiles, induced electrical field strength, velocity and viscosity profiles and pressure drop have been studied. As expected, the local EDL potential, local charge density and electrical field strength increases with decreasing K and/or increasing S. The velocity profiles cross-over away from the charged pipe wall with increasing K and/or decreasing n. The maximum velocity at the center of the pipe increases with increasing n and/or increasing S and/or decreasing K. The shear-thinning fluid viscosity is strongly dependent on K and S, whereas the shear-thickening viscosity is very weakly dependent on K and S. For fixed K, as the fluid behaviour changes from Newtonian (n = 1) to shear-thinning (n < 1), the induced electrical field strength increases and maximum velocity reduces. On the other hand, the change in fluid behaviour from Newtonian (n = 1) to shear-thickening (n > 1) decreases the electrical field strength and increases the maximum velocity. The non-Newtonian effects on maximum velocity and pressure drop are stronger in shear-thinning fluids at small K and large S, the shear-thickening fluids show opposite influence. Electroviscous effects enhance with decreasing K and/or increasing S. The electroviscous effects show complex dependence on the non-Newtonian tendency of the fluids. The shear-thickening (n > 1) fluids and/or smaller K show stronger influence on the pressure drop and thus, enhance the electroviscous effects than that in shear-thinning (n < 1) fluids and/or large K where EDL is very thin.


2013 ◽  
Vol 67 (6) ◽  
pp. 1247-1253 ◽  
Author(s):  
Yu-Hsiang Weng ◽  
Hsin-Chieh Wu ◽  
Kung-Cheh Li

Disposal and penetration of carbon nanotubes (CNTs) into the environment have raised increasing concerns over the years. In this study, a laboratory scale electro-microfiltration (EMF) was used to treat water containing single wall carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes (MWCNTs). The goal was to examine and compare the performance during EMF of SWCNT and MWCNT. The results showed that the initial flux was increased as the applied electrical voltage increased. At an applied pressure of 49 kPa, the final flux was comparable to pure water flux when the applied electrical field strength was greater than the critical electrical field strength (Ecritical). In addition, dissolved organic carbon (DOC) removal efficiency increased as the electrical voltage increased. Due to high convective transport of organic matter toward the membrane at 98 kPa, a decrease in DOC removal efficiency with increasing electrical field strength was observed. Overall, the fluxes and DOC removal efficiencies for EMF of SWCNT and MWCNT were not significantly different with a 95% confidence.


Sign in / Sign up

Export Citation Format

Share Document