scholarly journals Адитивне формування вуглекомпозитів на основі L-полілактиду

2020 ◽  
Vol 140 (6) ◽  
pp. 104-111
Author(s):  
Р. Ш. Іскандаров ◽  
Н. В. Сова ◽  
Б. М. Савченко ◽  
І. І. П'ятничук ◽  
В. А. Татаренко
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Polymer Matrix ◽  
Fiber Composites ◽  
Carbon Composite ◽  
Test Method ◽  
Carbon Fiber Composites ◽  
Injection Molded

Study of the FFF additive manufacturing process of composite material based on L – polylactide (PLLA) with ultra-short carbon fibers. Tensile strength and elongation at break for all test specimens were determined according to ISO 527. Tensile modulus - ASTM D638-10, specimen density - PN-EN ISO 1183, microscopic examination - according to ASTM E2015 - 04 (2014). Charpy Shock Tests ISO 179 and ASTM D256. Bending test method ISO 178 and ASTM D 790. The rational modes of FFF additive manufacturing (AM) of carbon fiber composite based on PLLA was established. Properties of carbon fiber PLLA and unfilled PLLA was determinated for AM formed samples and injection molded samples. Carbon fiber composites have significantly higher flexural and tensile module us values compared to the original L-polylactide, which is due to the effect of polymer matrix reinforcement by the fibrous component. However, finished products obtained by AM PLLA carbon composite have a lower impact strength and tensile strength, which is likely to be due to the fact that the carbon fibers are short (50-60 mkm) and have a cavitations effect during injection molding and AM. Density of carbon fiber filled PLLLA was lower the theoretically calculated value for filament material as well for injection molded and AM formed samples. Density reduction probably the main cause of impact properties deterioration due to cavity forming around carbon fibers. Density and tensile properties of AM formed samples can be changed by AM slicing parameter – extrusion multiplier. Cavitation effect for carbon fiber composites observed for PLLA composite in form AM filament, injection molded parts and AM formed samples. Cavity forming was confirmed by optical microscopy and density measurement. Possible reason for cavity forming is orientation deformation of the fiber in polymer matrix during the formation of the filament. The effect of cavitation also persists in the AM of products from carbon composites due to the passage of the orientation at the exit of the printer nozzle.  The possibility of regulating the density and physical and mechanical properties of carbon composite products obtained by the additive manufacturing method has been established. Selection of rational values of the extrusion multiplier and the direction of the layers in the additive molding allows you to create products with the desired complex of properties.

scholarly journals Experimental Investigation of Additive Manufacturing of Continuous Carbon Fiber Composites with Multifunctional Electro-Tensile Properties

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6574
Author(s):  
Ritesh Ghimire ◽  
Frank Liou
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
Electrical Properties ◽  
Carbon Fiber ◽  
Ultimate Tensile Strength ◽  
Tensile Properties ◽  
Fiber Composites ◽  
Carbon Fiber Composites ◽  
Continuous Carbon Fiber ◽  
Multifunctional Properties

Manufacturing processes for monofunctional and multifunctional materials vary depending on the design optimization. Multifunctional continuous carbon fiber composites provide great potential in achieving coupled structural and electrical properties for their applications in aircraft, unmanned aircraft systems, and spacecraft. Proper optimization of tensile and electrical properties offers benefits early in the design and continuous operational safety phases to obtain coupled multifunctional properties. In this paper, fused filament fabrication additive manufacturing (AM) technique was used to fabricate continuous carbon fiber solid laminated composites test coupons. The proposed new method characterizes the electrical conductivity’s coupled effects on the tensile properties, including the failure loads and modes. This paper addresses a novel way of integrating electrical function into the composites that significantly reduce weight, potentially replacing the bulky electrical wires. Tensile and electrical conductivity tests were concurrently conducted on coupons, and the results were plotted and tabulated. The results showed the multifunctional properties of the maximum ultimate tensile strength of 392 MPa with the maximum tensile load of 8907 N, and resistance of 37.5 G·Ω. The average values for ultimate tensile strength and maximum load were 371 MPa and 8459 N, respectively.

Reliability in the characterization of fiber length distributions of injection molded long carbon fiber composites

2017 ◽  
Vol 39 (12) ◽  
pp. 4594-4604 ◽  
Author(s):  
Bhisham N. Sharma ◽  
Seth A. Kijewski ◽  
Leonard S. Fifield ◽  
Yongsoon Shin ◽  
Charles L. Tucker ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fiber Length ◽  
Fiber Composites ◽  
Carbon Fiber Composites ◽  
Injection Molded ◽  
Long Carbon Fiber

Grafting carbon nanotubes densely on carbon fibers by poly(propylene imine) for interfacial enhancement of carbon fiber composites

Carbon ◽  
2020 ◽  
Vol 158 ◽  
pp. 704-710 ◽  
Author(s):  
Qiang Chen ◽  
Qingyu Peng ◽  
Xu Zhao ◽  
Hao Sun ◽  
Shasha Wang ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Fiber Composites ◽  
Carbon Fiber Composites ◽  
Poly Propylene

scholarly journals Structure, Mechanical and Thermal Properties of Polyphenylene Sulfide and Polysulfone Impregnated Carbon Fiber Composites

Polymers ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 684 ◽  
Author(s):  
Chukov ◽  
Nematulloev ◽  
Zadorozhnyy ◽  
Tcherdyntsev ◽  
Stepashkin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Carbon Fibers ◽  
Fiber Composites ◽  
Chemical Oxidation ◽  
Interfacial Interaction ◽  
Polyphenylene Sulfide ◽  
Carbon Fiber Composites ◽  
Mechanical And Thermal Properties ◽  
Thermal And Mechanical Properties

The paper studies new high-temperature thermoplastic impregnated unidirectional carbon fiber composites. The research focuses on the effect of thermal and chemical oxidation of the carbon fibers surface on the interfacial interaction between fibers and polysulfone and polyphenylene sulfide as well as thermal and mechanical properties of the composites. The research reveals the interaction between carbon fibers and the polymer matrix depend both on the type of surface treatment and nature of the polymer. The chemical oxidation of carbon fibers results in good interfacial interaction, and the best mechanical properties were observed for tows impregnated with polyphenylene sulfide.

Sign in / Sign up

Export Citation Format

Share Document