scholarly journals Removal of Ni (II) from Aqueous Solution by Adsorption onto Activated Carbon Prepared from Lapsi (Choerospondias axillaris) Seed Stone

2014 ◽  
Vol 9 (1) ◽  
pp. 166-174 ◽  
Author(s):  
Rajeshwar M. Shrestha ◽  
Margit Varga ◽  
Imre Varga ◽  
Amar P. Yadav ◽  
Bhadra P. Pokharel ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Characterization ◽  
Maximum Adsorption Capacity ◽  
Adsorption Data ◽  
Optimum Ph ◽  
Nickel Adsorption

Activated carbons were prepared from Lapsi seed stone by the treatment with H2SO4 and HNO3 for the removal of Ni (II) ions from aqueous solution. Two activated carbon have been prepared from Lapsi seed stones by treating with conc.H2SO4 and a mixture of H2SO4 and HNO3 in the ratio of 1:1 by weight for removal of Ni(II) ions. Chemical characterization of the resultant activated carbons was studied by Fourier Transform Infrared Spectroscopy and Boehm titration which revealed the presence of oxygen containing surface functional groups like carboxyl, lactones and phenols in the carbons. The optimum pH for nickel adsorption is found to be 5. The adsorption data were better fitted with the Langmuir equations than Freundlich adsorption equation to describe the equilibrium isotherms. The maximum adsorption capacity of Ni (II) on the resultant activated carbons was 28.25.8 mg g-1 with H2SO4 and 69.49 mg g-1 with a mixture of H2SO4 and HNO3. The waste material used in the preparation of the activated carbons is inexpensive and readily available. Hence the carbons prepared from Lapsi seed stones can act as potential low cost adsorbents for the removal of Ni (II) from water. DOI: http://dx.doi.org/10.3126/jie.v9i1.10680Journal of the Institute of Engineering, Vol. 9, No. 1, pp. 166–174

scholarly journals Preparation of Activated Carbon for the Removal of Pb (II) from Aqueous Solutions

2013 ◽  
Vol 28 ◽  
pp. 94-101 ◽  
Author(s):  
Rajeshwar Man Shrestha ◽  
Raja Ram Pradhananga ◽  
Margit Varga ◽  
Imre Varga
Keyword(s):  
Activated Carbon ◽  
Metal Ion ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Characterization ◽  
Batch Process ◽  
Chemical Society ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Removal Of Metal Ions

The present study deals with the use of activated carbons prepared from Lapsi seed stone as adsorbents for the removal of Pb (II) ions from aqueous solution. Two series of carbon have been prepared from Lapsi seed stones by treating with conc. H2SO4 and a mixture of H2SO4 and HNO3 in the ratio of 1:1 by weight for removal of metal ions. Chemical characterization of the resultant activated carbon was studied by Fourier Transform Infrared Spectroscopy and Boehm titration which revealed the presence of oxygen containing surface functional groups like carboxylic, lactonic, phenolic in the carbons. The effect of pH and initial metal ion concentration on the adsorption was studied in a batch process mode. The optimum pH for lead adsorption is found to be equal to 5. The adsorption data were better fitted with the Langmuir equations than Freundlich adsorption equation to describe the equilibrium isotherms. The maximum adsorption capacity of Pb (II) on the resultant activated carbons was 277.8 mg g-1 with H2SO4 and 423.7 mg g-1 with a mixture of H2SO4 and HNO3. The waste material used in the preparation of the activated carbons is inexpensive and readily available. Hence the carbons prepared from Lapsi seed stones can act as potential low cost adsorbents for the removal of Pb (II) from water. DOI: http://dx.doi.org/10.3126/jncs.v28i0.8114 Journal of Nepal Chemical Society Vol. 28, 2011 Page: 94-101 Uploaded Date: May 24, 2013

scholarly journals Preparation and characterization of activated carbon from Amygdalus Scoparia shell by chemical activation and its application for removal of lead from aqueous solutions

2010 ◽  
Vol 8 (6) ◽  
pp. 1273-1280 ◽  
Author(s):  
Sayed Mohammadi ◽  
Mohammad Karimi ◽  
Daryoush Afzali ◽  
Fatemeh Mansouri
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Low Cost ◽  
Chemical Activation ◽  
Maximum Adsorption Capacity ◽  
Batch Tests ◽  
Amygdalus Scoparia ◽  
Langmuir And Freundlich Equations ◽  
Characterization Of Activated Carbon

AbstractTwo series of activated carbon have been prepared by chemical activation of Amygdalus Scoparia shell with phosphoric acid or zinc chloride for the removal of Pb(II) ions from aqueous solutions. Several methods were employed to characterize the active carbon produced. The surface area was calculated using the standard Brunauer-Emmet-Teller method. The microstructures of the resultant activated carbon were observed by scanning electron microscopy. The chemical composition of the surface resultant activated carbon was determined by Fourier transform infrared spectroscopy. In the batch tests, the effect of pH, initial concentration, and contact time on the adsorption were studied. The data were fitted with Langmuir and Freundlich equations to describe the equilibrium isotherms. The maximum adsorption capacity of Pb(II) on the resultant activated carbon was 36.63 mg g−1 with H3PO4 and 28.74 mg g−1 with ZnCl2. To regenerate the spent adsorbents, desorption experiments were performed using 0.25 mol L−1 HCl. Here we propose that the activated carbon produced from Amygdalus Scoparia shell is an alternative low-cost adsorbent for Pb(II) adsorption.

Characterization of the Corallina Elongata Alga and Study of its Biosorption Properties for Methylene Blue

2019 ◽  
Vol 41 (1) ◽  
pp. 62-62
Author(s):  
Farida Bouremmad Farida Bouremmad ◽  
Abdennour Bouchair Abdennour Bouchair ◽  
Sorour Semsari Parapari Sorour Semsari Parapari ◽  
Shalima Shawuti and Mehmet Ali Gulgun Shalima Shawuti and Mehmet Ali Gulgun
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Mediterranean Coast ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Aquatic Biomass ◽  
Equilibrium Data

Biosorbents can be an alternative to activated carbon. They are derived from agricultural by-products or aquatic biomass. They are low cost and they may have comparable performances to those of activated carbon. The present study focuses on the characterization of the Corallina Elongata (CE) alga and its adsorption performance for Methylene Blue (MB), this alga is found in abundance at the Mediterranean coast of the city of Jijel in eastern Algeria. The dried alga was characterized using various characterization techniques such as DTA, TG, FTIR, XRD, SEM and EDX, which showed that the material consists essentially of a calcite containing magnesium. Batch adsorption studies were carried out and the effect of experimental parameters Such as pH, initial dye concentration, temperature, adsorbent dose and contact time, on the adsorption of MB was studied. The kinetic experimental data were found to conform to the pseudo-second-order model with good correlation and equilibrium data were best fitted to The Langmuir model, with a maximum adsorption capacity of 34.4 mg/g. The adsorption isotherms at various temperatures allowed the determination of certain thermodynamic parameters (ΔG, ΔH and ΔS). Finally, the adsorption results showed a good affinity between CE and MB with a high adsorption capacity.

The Adsorption Isotherm Studies of Orange Peel on Pesticide Furadan

2013 ◽  
Vol 477-478 ◽  
pp. 1331-1335
Author(s):  
Guang Fu Xu ◽  
Hui Min Jing ◽  
Rui Xin Guo
Keyword(s):  
Aqueous Solution ◽  
Adsorption Isotherm ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Agricultural Waste ◽  
Orange Peel ◽  
Maximum Adsorption Capacity ◽  
Attractive Candidate ◽  
Adsorption Data ◽  
Langmuir And Freundlich Models

Orange peel, an agricultural waste available in large quantity in China, was utilized as low-cost adsorbent to remove furadan from aqueous solution by adsorption. Adsorption isotherms were calculated and discussed. Both Langmuir and Freundlich models fitted the adsorption data quite reasonably (R2> 0.98) and the maximum adsorption capacity was 161.29 mg.g-1. The results in this study indicated that orange peel was an attractive candidate for removing furadan from the aqueous solution.

scholarly journals Preparation of Activated Carbons from Spent Coffee Grounds and Coffee Parchment and Assessment of Their Adsorbent Efficiency

Processes ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 1396
Author(s):  
Gustavo A. Figueroa Campos ◽  
Jeffrey Paulo H. Perez ◽  
Inga Block ◽  
Sorel Tchewonpi Sagu ◽  
Pedro Saravia Celis ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Activated Carbons ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Spent Coffee Grounds ◽  
Hydrophobic Compounds ◽  
Coffee Grounds ◽  
By Products

The valorization of coffee wastes through modification to activated carbon has been considered as a low-cost adsorbent with prospective to compete with commercial carbons. So far, very few studies have referred to the valorization of coffee parchment into activated carbon. Moreover, low-cost and efficient activation methods need to be more investigated. The aim of this work was to prepare activated carbon from spent coffee grounds and parchment, and to assess their adsorption performance. The co-calcination processing with calcium carbonate was used to prepare the activated carbons, and their adsorption capacity for organic acids, phenolic compounds and proteins was evaluated. Both spent coffee grounds and parchment showed yields after the calcination and washing treatments of around 9.0%. The adsorption of lactic acid was found to be optimal at pH 2. The maximum adsorption capacity of lactic acid with standard commercial granular activated carbon was 73.78 mg/g, while the values of 32.33 and 14.73 mg/g were registered for the parchment and spent coffee grounds activated carbons, respectively. The Langmuir isotherm showed that lactic acid was adsorbed as a monolayer and distributed homogeneously on the surface. Around 50% of total phenols and protein content from coffee wastewater were adsorbed after treatment with the prepared activated carbons, while 44, 43, and up to 84% of hydrophobic compounds were removed using parchment, spent coffee grounds and commercial activated carbon, respectively; the adsorption efficiencies of hydrophilic compounds ranged between 13 and 48%. Finally, these results illustrate the potential valorization of coffee by-products parchment and spent coffee grounds into activated carbon and their use as low-cost adsorbent for the removal of organic compounds from aqueous solutions.

scholarly journals Activated Carbon from the Peelings of Cassava Tubers (Manihot esculenta) for the Removal of Nickel(II) Ions from Aqueous Solution

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Brice Armel Ajouafeu Alongamo ◽  
Lydie Dodo Ajifack ◽  
Julius Numbonui Ghogomu ◽  
Ndi Julius Nsami ◽  
Joseph Mbadcam Ketcha
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Manihot Esculenta ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Activation ◽  
Zero Point ◽  
Batch Adsorption ◽  
Homogeneous Surface

Activated carbons were obtained from the peelings of cassava tubers (Manihot esculenta) by chemical activation using potassium hydroxide and phosphoric acid at impregnation ratios of 2 : 1 and 1 : 1, respectively, at 400°C for batch adsorption of nickel(II) ions from aqueous solution. Characterization of activated carbon samples was achieved via proximate analysis, Fourier-transform infrared spectroscopy, pH of zero-point charge, Boehm method, elemental analysis, scanning electron microscopy, and iodine number determination for each adsorbent. The effects of pH, contact time, initial adsorbate concentration, and adsorbent dose were studied at 27°C in order to optimize the conditions for maximum adsorption. Equilibrium was attained after 40 minutes of contact of both materials with activating solutions. Maximum adsorption capacities of 41.15 mg/g for ACPH, 47.39 mg/g for ACPA, 35.34 mg/g for NIC, and 34.48 mg/g for RM, respectively, were obtained at pH = 4. Equilibrium data showed that the Langmuir model best described the adsorption process with R2 closed to unity, indicative of monolayer adsorption on a homogeneous surface. Kinetic studies showed that the adsorption process is controlled by the pseudo-second-order model. These results show that activated carbon prepared from cassava peelings constitutes an effective low-cost material for the treatment of wastewater containing nickel(II) ions.

Adsorption of Mercury Ion on Activated Carbons from Rice Husk

2012 ◽  
Vol 161 ◽  
pp. 162-166 ◽  
Author(s):  
Xiao Lan SONG ◽  
Ying Zhang ◽  
Cheng Yin Yan ◽  
Wen Juan Jiang ◽  
Hong Jiang Xie
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Rice Husk ◽  
Activated Carbons ◽  
Langmuir Model ◽  
Mercury Ion ◽  
Maximum Adsorption Capacity ◽  
Adsorption Performance ◽  
Monolayer Adsorption ◽  
Adsorption Data

The adsorption performance of mercury ion onto activated carbon prepared from rice husk with NaOH was carried out at initial concentration of 100 mg/L. The activated carbon obtained at 800 °C possessed the outstanding specific surface area of 2786 m2/g. And the results showed that the maximum adsorption capacity of Hg2+ was recorded as 342.0 mg/g due to abundant micropores of 1.076 nm. In addition, the adsorption data were well explained by the Langmuir model with the monolayer adsorption capacity of 555.6 mg/g.

scholarly journals Adsorptive removal of Pb(II) ions from aqueous solution by activated carbon prepared from cabbage waste

2020 ◽  
Vol 8 ◽  
pp. 1-10
Author(s):  
Keshav Raj Paneru ◽  
Binay Kumar Jha
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Specific Surface ◽  
Metal Ion ◽  
Activated Carbons ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Adsorption Method ◽  
Surface Areas

The present study deals with the adsorption of Pb(II) from an aqueous solution on activated carbon obtained from cabbage waste. Such activated carbon was prepared by pyrolysis of cabbage waste powder at 700 °C for 1 hour in three different atmospheres, namely open air (CWAC-O), nitrogen (CWAC-N) and nitrogen with steam (CWWAC-NW). The specific surface areas of thus obtained three types of activated carbons were determined by methylene blue adsorption method and found for CWAC-O, CWAC-N and CWAC-NW as 59, 169 and 310 m2/g, respectively. Due to the highest specific surface area of CWAC-NW, the adsorption of Pb(II) experiments was performed onto CWAC-NW only. The influence of various parameters like pH, adsorbent dose, contact time and different initial concentrations of metal ion on adsorption of Pb(II) were studied. The equilibrium data for adsorption was analyzed by using Langmuir and Freundlich isotherm models. The Langmuir adsorption isotherm model was found the best fit for the experimental data. The maximum adsorption capacity was 54.945 mg/g. Kinetics results were described by a pseudo second order model with the rate constant value 0.055 g/(mg∙min). The main mechanism of the adsorption process was physicochemical adsorption and was not solely intraparticle diffusion.

Sign in / Sign up

Export Citation Format

Share Document