scholarly journals Computational Fluid Dynamics Study of Balloon System Tethered to a Stratosail

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Jayakanth Loganathan ◽  
Kian-Meng Lim ◽  
Heow Pueh Lee ◽  
Boo Cheong Khoo
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Drift Velocity ◽  
Numerical Study ◽  
Cfd Simulations ◽  
Wind Speeds ◽  
Drag Forces ◽  
Stratospheric Balloon ◽  
Computational Fluid Dynamics Cfd ◽  
Balloon System

In this paper, we present a numerical study of a stratospheric balloon system tethered to a passive device, known as the Stratosail, for station-keeping operation. For scientific applications, stratospheric balloons that operate at altitudes between 15 and 20 km will need to maintain station over a fixed point above the earth for a prescribed period of time. This is a challenging problem due to the limitation of payloads and lack of an energy source. The present study uses computational fluid dynamics (CFD) simulations to analyze the drift velocity of such a balloon-Stratosail system under typical wind conditions in the stratosphere. The Stratosail is attached below the super-pressure helium balloon via a long and thin tether about 10 to 15 km below the balloon, providing a drag force to alter the flight path of the balloon. Its operation depends on the natural differences in the wind speed and wind direction at different altitudes in the atmosphere that act on the balloon and the Stratosail (spaced far apart by 10km to 15 km). In this study, we calculated the drag forces on the balloon and Stratosail for typical wind speeds at various altitudes in the stratosphere. The tether was also modelled as a cable joining the balloon and sail. With this model, the drift velocity of the system was calculated for various altitudes and the angle of attack of the sail.

Numerical Study of Micromixers for Stopped Flow

2011 ◽  
Author(s):  
Dominik Du¨chs ◽  
Sabine Brunklaus ◽  
Peter Spang ◽  
Marion Ritzi-Lehnert ◽  
Klaus Drese
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Potential Application ◽  
Numerical Study ◽  
Stopped Flow ◽  
Microfluidic Chips ◽  
Cfd Simulations ◽  
Mixing Parameter ◽  
Different Types ◽  
Computational Fluid Dynamics Cfd

Computational fluid dynamics (CFD) simulations are conducted to compare the efficiency of different types of micromixers with respect to their potential application in chip-based stopped-flow designs. The evaluation of a mixing parameter for different geometries and at various flow velocities enables a comparison between the Berger ball mixer and other designs that are in principle suitable for applications in microfluidic chips.

scholarly journals Missile Grid Fins Analysis using Computational Fluid Dynamics: A Systematic Review

2019 ◽  
Vol 11 (1) ◽  
pp. 151-169 ◽  
Author(s):  
Nayhel SHARMA ◽  
Rakesh KUMAR
Keyword(s):  
Fluid Dynamics ◽  
Systematic Review ◽  
Computational Fluid Dynamics ◽  
Air Flow ◽  
Post Processing ◽  
Cfd Simulations ◽  
Drag Forces ◽  
Computational Fluid Dynamics Cfd ◽  
Work Done ◽  
Control Surfaces

Grid Fins are unconventional control surfaces, consisting of cells in an outer frame. Uniqueness of Grid Fins is that they are aligned parallel to the direction of air flow. The orientation of these fins results in aerodynamic demerits such as choking of flow inside the cells and thereby resulting in increased drag forces. Both experimental and Computational Fluid Dynamics (CFD) studies have been employed in negating these effects. This paper reviews the work done by various authors to overcome the anomalies using CFD approach. This paper also discusses the measures to overcome these anomalies. The paper presents an insight and step by step guidelines for CFD simulations right from the pre-processing to the post-processing.

scholarly journals Rapid pivot feeding in pipefish: flow effects on prey and evaluation of simple dynamic modelling via computational fluid dynamics

2008 ◽  
Vol 5 (28) ◽  
pp. 1291-1301 ◽  
Author(s):  
Sam Van Wassenbergh ◽  
Peter Aerts
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Analytical Model ◽  
Dynamic Modelling ◽  
Head Rotation ◽  
Theoretical Models ◽  
Cfd Simulations ◽  
Deceleration Phase ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Effects

Most theoretical models of unsteady aquatic movement in organisms assume that including steady-state drag force and added mass approximates the hydrodynamic force exerted on an organism's body. However, animals often perform explosively quick movements where high accelerations are realized in a few milliseconds and are followed closely by rapid decelerations. For such highly unsteady movements, the accuracy of this modelling approach may be limited. This type of movement can be found during pivot feeding in pipefish that abruptly rotate their head and snout towards prey. We used computational fluid dynamics (CFD) to validate a simple analytical model of cranial rotation in pipefish. CFD simulations also allowed us to assess prey displacement by head rotation. CFD showed that the analytical model accurately calculates the forces exerted on the pipefish. Although the initial phase of acceleration changes the flow patterns during the subsequent deceleration phase, the accuracy of the analytical model was not reduced during this deceleration phase. Our analysis also showed that prey are left approximately stationary despite the quickly approaching pipefish snout. This suggests that pivot-feeding fish need little or no suction to compensate for the effects of the flow induced by cranial rotation.

scholarly journals Effect of hydraulic and geometric factors upon leakage flow rate in pressurized pipes

RBRH ◽  
2021 ◽  
Vol 26 ◽  
Author(s):  
Mayara Francisca da Silva ◽  
Fábio Veríssimo Gonçalves ◽  
Johannes Gérson Janzen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Leakage Flow ◽  
Cfd Simulations ◽  
Mean Velocity ◽  
Leakage Flow Rate ◽  
Geometric Factors ◽  
Leakage Area ◽  
Computational Fluid Dynamics Cfd

ABSTRACT Computational Fluid Dynamics (CFD) simulations of a leakage in a pressurized pipe were undertaken to determine the empirical effects of hydraulic and geometric factors on the leakage flow rate. The results showed that pressure, leakage area and leakage form, influenced the leakage flow rate significantly, while pipe thickness and mean velocity did not influence the leakage flow rate. With relation to the interactions, the effect of pressure upon leakage flow rate depends on leakage area, being stronger for great leakage areas; the effects of leakage area and pressure on leakage flow rate is more pronounced for longitudinal leakages than for circular leakages. Finally, our results suggest that the equations that predict leakage flow rate in pressurized pipes may need a revision.

scholarly journals The Protect Air Film of an Exterior Window

2021 ◽  
Author(s):  
Sanaz Dianat
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Speed ◽  
Glass Temperature ◽  
Experimental Procedure ◽  
Wind Speeds ◽  
Computational Fluid Dynamics Cfd ◽  
Air Film ◽  
The Impact

The research paper investigates the impact of a window’s exterior air film on the assembly temperature. The exterior air film constitutes a vital portion of a window’s insulating values. The air film increases the temperature of the window exterior pane to a temperature above ambient temperature. The air film also rises the interior glass temperature and reduces the heat transfer from the interior surface. According to computational fluid dynamics (CFD), the air film is removed in windy conditions, decreasing the window temperature on the outside as well as on the inside. The idea behind the project is to carry out an experimental procedure on three different windows to validate the CFD results, which indicates the effect of various wind speeds. Keyword: Exterior air film, computational fluid dynamics, window assembly, wind speed

scholarly journals The Aerodynamics of a Diabolo

2021 ◽  
Author(s):  
Darren Jia
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Angular Momentum ◽  
Flow Pattern ◽  
High Spin ◽  
Angular Speed ◽  
Geometric Shape ◽  
Cfd Simulations ◽  
Resistive Torque ◽  
Computational Fluid Dynamics Cfd

Diabolo is a popular game in which the object can be spun at up to speeds of 5000 rpm. This high spin velocity gives the diabolo the necessary angular momentum to remain stable. The shape of the diabolo generates an interesting air flow pattern. The viscous air applies a resistive torque on the fast spinning diabolo. Through computational fluid dynamics (CFD) simulations it's shown that the resistive torque has an interesting dependence on the angular speed of the diabolo. Further, the geometric shape of the diabolo affects the dependence of torque on angular speed.

scholarly journals The Protect Air Film of an Exterior Window

2021 ◽  
Author(s):  
Sanaz Dianat
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Speed ◽  
Glass Temperature ◽  
Experimental Procedure ◽  
Wind Speeds ◽  
Computational Fluid Dynamics Cfd ◽  
Air Film ◽  
The Impact

The research paper investigates the impact of a window’s exterior air film on the assembly temperature. The exterior air film constitutes a vital portion of a window’s insulating values. The air film increases the temperature of the window exterior pane to a temperature above ambient temperature. The air film also rises the interior glass temperature and reduces the heat transfer from the interior surface. According to computational fluid dynamics (CFD), the air film is removed in windy conditions, decreasing the window temperature on the outside as well as on the inside. The idea behind the project is to carry out an experimental procedure on three different windows to validate the CFD results, which indicates the effect of various wind speeds. Keyword: Exterior air film, computational fluid dynamics, window assembly, wind speed

scholarly journals Comparison of Blade Element Method and CFD Simulations of a 10 MW Wind Turbine

Fluids ◽  
2018 ◽  
Vol 3 (4) ◽  
pp. 73 ◽  
Author(s):  
Galih Bangga
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Separation ◽  
Spatial Interpolation ◽  
Flow Conditions ◽  
Cfd Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Correction Terms ◽  
Selection Of ◽  
Blade Element

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

Sign in / Sign up

Export Citation Format

Share Document