scholarly journals Effect of hydraulic and geometric factors upon leakage flow rate in pressurized pipes

RBRH ◽  
2021 ◽  
Vol 26 ◽  
Author(s):  
Mayara Francisca da Silva ◽  
Fábio Veríssimo Gonçalves ◽  
Johannes Gérson Janzen
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Rate ◽  
Leakage Flow ◽  
Cfd Simulations ◽  
Mean Velocity ◽  
Leakage Flow Rate ◽  
Geometric Factors ◽  
Leakage Area ◽  
Computational Fluid Dynamics Cfd

ABSTRACT Computational Fluid Dynamics (CFD) simulations of a leakage in a pressurized pipe were undertaken to determine the empirical effects of hydraulic and geometric factors on the leakage flow rate. The results showed that pressure, leakage area and leakage form, influenced the leakage flow rate significantly, while pipe thickness and mean velocity did not influence the leakage flow rate. With relation to the interactions, the effect of pressure upon leakage flow rate depends on leakage area, being stronger for great leakage areas; the effects of leakage area and pressure on leakage flow rate is more pronounced for longitudinal leakages than for circular leakages. Finally, our results suggest that the equations that predict leakage flow rate in pressurized pipes may need a revision.

scholarly journals Rapid pivot feeding in pipefish: flow effects on prey and evaluation of simple dynamic modelling via computational fluid dynamics

2008 ◽  
Vol 5 (28) ◽  
pp. 1291-1301 ◽  
Author(s):  
Sam Van Wassenbergh ◽  
Peter Aerts
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Analytical Model ◽  
Dynamic Modelling ◽  
Head Rotation ◽  
Theoretical Models ◽  
Cfd Simulations ◽  
Deceleration Phase ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Effects

Most theoretical models of unsteady aquatic movement in organisms assume that including steady-state drag force and added mass approximates the hydrodynamic force exerted on an organism's body. However, animals often perform explosively quick movements where high accelerations are realized in a few milliseconds and are followed closely by rapid decelerations. For such highly unsteady movements, the accuracy of this modelling approach may be limited. This type of movement can be found during pivot feeding in pipefish that abruptly rotate their head and snout towards prey. We used computational fluid dynamics (CFD) to validate a simple analytical model of cranial rotation in pipefish. CFD simulations also allowed us to assess prey displacement by head rotation. CFD showed that the analytical model accurately calculates the forces exerted on the pipefish. Although the initial phase of acceleration changes the flow patterns during the subsequent deceleration phase, the accuracy of the analytical model was not reduced during this deceleration phase. Our analysis also showed that prey are left approximately stationary despite the quickly approaching pipefish snout. This suggests that pivot-feeding fish need little or no suction to compensate for the effects of the flow induced by cranial rotation.

scholarly journals The Aerodynamics of a Diabolo

2021 ◽  
Author(s):  
Darren Jia
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Angular Momentum ◽  
Flow Pattern ◽  
High Spin ◽  
Angular Speed ◽  
Geometric Shape ◽  
Cfd Simulations ◽  
Resistive Torque ◽  
Computational Fluid Dynamics Cfd

Diabolo is a popular game in which the object can be spun at up to speeds of 5000 rpm. This high spin velocity gives the diabolo the necessary angular momentum to remain stable. The shape of the diabolo generates an interesting air flow pattern. The viscous air applies a resistive torque on the fast spinning diabolo. Through computational fluid dynamics (CFD) simulations it's shown that the resistive torque has an interesting dependence on the angular speed of the diabolo. Further, the geometric shape of the diabolo affects the dependence of torque on angular speed.

scholarly journals Comparison of Blade Element Method and CFD Simulations of a 10 MW Wind Turbine

Fluids ◽  
2018 ◽  
Vol 3 (4) ◽  
pp. 73 ◽  
Author(s):  
Galih Bangga
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Flow Separation ◽  
Spatial Interpolation ◽  
Flow Conditions ◽  
Cfd Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Correction Terms ◽  
Selection Of ◽  
Blade Element

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

scholarly journals Analysis of a Converging, Annular, Isothermal Melt Blowing Jet Using Computational Fluid Dynamics

2005 ◽  
Vol os-14 (3) ◽  
pp. 1558925005os-14
Author(s):  
Eric M. Moore ◽  
Dimitrios V. Papavassiliou ◽  
Robert L. Shambaugh
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Kinetic Energy ◽  
Near Field ◽  
Flow Characteristics ◽  
Sectional Area ◽  
Melt Blowing ◽  
Mean Velocity ◽  
Cross Sectional ◽  
Computational Fluid Dynamics Cfd

An unconventional melt blowing die was analyzed using computational fluid dynamics (CFD). This die has an annular configuration wherein the jet inlet is tapered (the cross-sectional area decreases) as the air approaches the die face. It was found that the flow characteristics of this die are different from conventional slot and annular dies. In particular, for the tapered die the near-field normalized turbulent kinetic energy was found to be lower at shallow die angles. Also, it was found that the peak mean velocity behavior was intermediate between that of conventional annular and slot dies. The centerline turbulence profiles were found to be qualitatively similar to those of annular dies; quantitatively, higher values were present for tapered dies.

scholarly journals Investigation of Influence of Adjustments in Cyclist Arm Position on Aerodynamic Drag Using Computational Fluid Dynamics

Proceedings ◽  
2020 ◽  
Vol 49 (1) ◽  
pp. 159
Author(s):  
Knut Erik Teigen Giljarhus ◽  
Daniel Årrestad Stave ◽  
Luca Oggiano
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Aerodynamic Drag ◽  
Time Trial ◽  
Elbow Extension ◽  
Cfd Simulations ◽  
Arm Position ◽  
Sport Activities ◽  
The Face ◽  
Computational Fluid Dynamics Cfd

In professional cycling, even small adjustments in position could mean that valuable seconds are gained over the course of a time-trial race. This study investigates the influence of arm position on the aerodynamic drag of a cyclist. Based on a 3D scanned model of a professional cyclist, 64 alternate positions are generated. The parameters that are investigated are the distance between elbows, elbow extension, and distance between hands. Computational fluid dynamics (CFD) simulations of all positions are performed, and a regression model is built from the results. The results indicate that the optimal posture is achieved for a minimum in all investigated parameters, which means that the hands and elbows should be kept together with hands up towards the face. Furthermore, elbow extension seems to be the most crucial parameter, followed by the distance between elbows, and then by the distance between the hands. The presented methodology can be applied to study other parameters relevant to cycling aerodynamics or be applied to other sport activities as well.

Study of Gas Shortcut Flow Rate in Cyclone with Different Inlet Section Angles Using Response Surface Methodology

2009 ◽  
Vol 7 (1) ◽  
Author(s):  
Fuping Qian ◽  
Xingwei Huang ◽  
Mingyao Zhang
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Flow Rate ◽  
Numerical Solutions ◽  
Inlet Section ◽  
Statistical Software ◽  
Vortex Finder ◽  
Computational Fluid Dynamics Cfd

Numerical simulations of cyclones with various vortex finder dimensions and inlet section angles were performed to study the gas shortcut flow rate. The numerical solutions were carried out using commercial computational fluid dynamics (CFD) code Fluent 6.1. A prediction model of the gas shortcut flow rate was obtained based on response surface methodology by means of the statistical software program (Minitab V14). The results show that the length of the vortex finder insertion, the vortex finder diameter and the inlet section angle play an important role in influencing the gas shortcut flow rate. The gas shortcut flow rate decreases when increasing the inlet section angle, and increases when increasing the vortex finder diameter and decreasing the length of the vortex finder insertion. Compared with the effect of the length of the vortex finder insertion on the shortcut flow rate, the effect of the vortex finder diameter on the gas shortcut flow rate seems more pronounced. The effect of the vortex finder dimension on the gas shortcut flow rate is changed with the different inlet section angles, i.e., the effects of the vortex finder dimension of the conventional cyclone (the inlet section angle is 0º) on the gas shortcut flow rate is stronger than the cyclone with 30º and 45º inlet section angles.

Measurement of the Aerodynamic Pressures Produced by Passing Trains

Joint Rail ◽  
2002 ◽  
Author(s):  
Robert A. MacNeill ◽  
Samuel Holmes ◽  
Harvey S. Lee
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
High Speed ◽  
Electric Locomotive ◽  
Cfd Simulations ◽  
Computational Fluid Dynamics Cfd ◽  
Freight Car

This paper describes measurement of the aerodynamic pressures produced by a Bombardier High-Speed Non-Electric Locomotive (HSNEL) on an adjacent stationary double-stack freight car. Static pressures are measured on the near and far-side faces of the freight containers over a range of locomotive speeds from 60 to 130 mph. This data is also compared with the pressures predicted by computational fluid dynamics (CFD) simulations.

Sign in / Sign up

Export Citation Format

Share Document