3DIC Fault Isolation Using the OBIRCH Approach

2011 ◽  
Author(s):  
Ming-Sung Hsu ◽  
Yian-Liang Kuo ◽  
Yu-Ting Lin ◽  
Ru-Ying Huang ◽  
Min-Feng Ku ◽  
...  
Keyword(s):  
Induced Resistance ◽  
Fault Isolation ◽  
Optical Beam ◽  
Resistance Change ◽  
Non Destructive

Abstract This paper uses an interesting specific case study to highlight the non-destructive fault isolation demonstration of 3DIC stacked dies applied the optical beam induced resistance change (OBIRCH) approach.

Using Electrical Fault Isolation and Characterization to Improve the Effectiveness of Physical Fault Isolation Techniques for Analog Circuits

2017 ◽  
Author(s):  
Jim Douglass ◽  
Sohrab Pourmand
Keyword(s):  
Induced Resistance ◽  
Analog Circuits ◽  
Fault Isolation ◽  
Optical Beam ◽  
Resistance Change ◽  
Isolation Techniques ◽  
Isolation And Characterization ◽  
Lock In

Abstract This paper shows that by combining electrical fault isolation and characterization by microprobing with physical fault isolation techniques both what is wrong with the circuit and where the defect is located can be determined with less microprobing and more safety from electrical recovery. In the first example, the unit was powered up using the optical beam induced resistance change (OBIRCH) supply, and OBIRCH was performed to determine if there were OBIRCH site differences between the good part and the return. The second example uses a combination of electrical fault isolation and characterization with microprobing and the physical fault isolation tool of lock in thermography (LIT). With these two examples, it has been shown that the use of electrical fault isolation and microprobing can be used to enhance the physical fault isolation tools of OBIRCH and LIT.

Investigating carrier transport paths in organic nonvolatile bistable memory by optical beam induced resistance change

2011 ◽  
Vol 12 (10) ◽  
pp. 1632-1637 ◽  
Author(s):  
Heng-Tien Lin ◽  
Chang-Yu Lin ◽  
Zingway Pei ◽  
Jun-Rong Chen ◽  
Yi-Jen Chan ◽  
...  
Keyword(s):  
Induced Resistance ◽  
Carrier Transport ◽  
Optical Beam ◽  
Resistance Change

High Resolution Electron Beam Induced Resistance Change for Fault Isolation with 100 nm2 Localization

2015 ◽  
Author(s):  
Brett A. Buchea ◽  
Christopher S. Butler ◽  
H.J. Ryu ◽  
Wen-hsien Chuang ◽  
Martin von Haartman ◽  
...  
Keyword(s):  
Electron Beam ◽  
High Resolution ◽  
Induced Resistance ◽  
Fault Isolation ◽  
Direct Stimulation ◽  
Resistance Change ◽  
Isolation Technique ◽  
High Resolution Imagery ◽  
Defect Isolation ◽  
Time Required

Abstract A novel fault isolation technique, electron beam induced resistance change (EBIRCh), allows for the direct stimulation and localization of eBeam current sensitive defects with resolution of approximately 100nm square, continuing a history of beam based failure isolation methods. EBIRCh has been shown to work over a range of defects, significantly decreasing the time required for isolation of shorts through straightforward high resolution imagery, allowing for explicit visual defect isolation with a linear resolution of approximately 10nm. This paper discusses the operational setups for the source and amplifier while performing an EBIRCh scan, describes the processes involved in the Intel test vehicle that was used to test EBIRCh, and provides information on two independent functional theories for EBIRCh that operate in conjunction to a greater or lesser extent depending on the defect type. EBIRCh is expected to improve through-put and resolution on various defect types compared to conventional fault isolation techniques.

A Simple Adapter for Soft Defect Localization Using OBIRCH

2007 ◽  
Author(s):  
Ted Kolasa
Keyword(s):  
Induced Resistance ◽  
Low Cost ◽  
Optical Beam ◽  
Significant Cost ◽  
Resistance Change ◽  
Design Considerations ◽  
Defect Localization

Abstract Equipment manufacturers have developed peripherals for their tools that add soft defect localization (SDL) capability to existing optical beam tools, in many cases providing excellent results. However, these upgrades add significant cost to the tool. This paper presents the design considerations for a simple adapter that was developed in house to add SDL capability to optical beam induced resistance change (OBIRCH) tool, including resolution of some unexpected problems. This solution represents a simple, low cost method to add SDL testing capability to the OBIRCH tool and can also be used in conjunction with OBIC and XIVA tools with little or no modification. An early example of the SDL results provided by this adapter is also presented.

High Resolution Localization Using Lock-in Based Electron Beam Methods

2017 ◽  
Author(s):  
Felix Rolf ◽  
Christian Hollerith ◽  
Christian Feuerbaum
Keyword(s):  
Electron Beam ◽  
High Resolution ◽  
Induced Resistance ◽  
High Efficiency ◽  
Optical Beam ◽  
Resistance Change ◽  
Root Cause ◽  
Special Challenge ◽  
Electron Beam Induced Current ◽  
Lock In

Abstract With decreasing transistor sizes accurate failure localization becomes more and more important in order to find the root cause of failures with high efficiency. Field returns are a special challenge, since there is usually only one sample for preparation. Hence, reliable high resolution localization is mandatory for a successful preparation. Optical beam induced resistance change (OBIRCH) is a powerful tool for localization but has resolution limitations due to the diameter of the optical beam. The tool can be further improved by the lock-in technique. In this paper we demonstrate that the lock-in technique can also be applied for electron beam localization methods like electron beam induced current (EBIC) / electron beam absorbed current (EBAC) and resistance change imaging (RCI) / electron beam induced resistance change (EBIRCH).

Sign in / Sign up

Export Citation Format

Share Document