scholarly journals Experimental study on annular cylindrical tuned liquid dampers for vibration control under different excitation angles

2021 ◽  
Vol 4 (3) ◽  
pp. 163-183
Author(s):  
Ahmet Can Altunışık ◽  
Volkan Kahya ◽  
Ali Yetişken
Keyword(s):  
Damping Ratio ◽  
Experimental Tests ◽  
Coupled System ◽  
Shaking Table ◽  
Ambient Vibration ◽  
Model Structure ◽  
Shaking Table Tests ◽  
Tuned Liquid Dampers ◽  
Ambient Vibration Tests ◽  
Liquid Dampers

This work aims to experimentally show the effectiveness of annular cylindrical tuned liquid dampers (ACTLDs) on the classical tuned liquid column dampers (TLCDs) under the effect of inclined ground motion. For experimental measurements, a single-story model structure constituted by two plates at the top and bottom connected by four columns was constructed. Since the water length within the tuned liquid dampers (TLDs) is a very important parameter that affects the performance of the absorber, ACTLD and TLCD devices were designed such that their total water lengths be equal for comparison purposes. The modal characteristics of the model structure were determined by ambient vibration tests. The resonant frequency, head-loss coefficient, damping ratio, and water height-frequency diagram of ACTLD and TLCD devices were obtained experimentally through the shaking table tests. Then, the shaking table tests on the model structure with and without the absorbers under consideration were performed to obtain the acceleration and displacement time-histories and the damping ratio for the coupled system. In experimental tests, different excitation directions from 0 to 90 deg were considered. Results of the study show that ACTLDs are better than TLCDs at suppressing vibrations caused by ground motions acting on the structure at oblique angles.

Tuned Liquid Damper Experiment Using Shaking Table

2013 ◽  
Vol 421 ◽  
pp. 772-777 ◽  
Author(s):  
Ki Pyo You ◽  
Young Moon Kim ◽  
Jang Youl You
Keyword(s):  
Natural Frequency ◽  
Damping Ratio ◽  
Tall Buildings ◽  
Excitation Amplitude ◽  
Shaking Table ◽  
Tuned Liquid Damper ◽  
Tuned Liquid Dampers ◽  
Liquid Dampers ◽  
Water Tanks ◽  
Wind Induced Vibration

The present study examines the characteristics of rectangular and circular tuned liquid dampers, which control wind-induced vibration in tall buildings, according to the natural frequency. The tuned liquid dampers (TLD) were of frequencies: 0.44Hz, 0.55Hz, 0.64Hz and 0.73Hz. The tuning feature of TLD water tanks was better in circular water tanks than in rectangular water tanks. Excitation amplitude affected the damping ratio based on energy dissipation capacity. At low excitation (below 5mm) and low natural frequency (0.44Hz), circular water tanks were advantageous over rectangular water tanks. However, at high excitation (over 5mm) and high natural frequency (over 0.55Hz), rectangular water tanks were advantageous over circular water tanks.

Comparative dynamic investigation of cross-laminated wooden panel systems: Shaking-table tests and analysis

2017 ◽  
Vol 21 (10) ◽  
pp. 1421-1436 ◽  
Author(s):  
Viktor Hristovski ◽  
Violeta Mircevska ◽  
Bruno Dujic ◽  
Mihail Garevski
Keyword(s):  
Energy Dissipation ◽  
Earthquake Engineering ◽  
Dynamic Properties ◽  
Seismic Energy ◽  
Experimental Tests ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Equivalent Viscous Damping ◽  
Cross Laminated Timber ◽  
Engineering Seismology

Cross-laminated timber has recently gained great popularity in earthquake-prone areas for construction of residential, administrative, and other types of buildings. At the Laboratory of the Institute of Earthquake Engineering and Engineering Seismology in Skopje, comparative full-scale shaking-table tests of cross-laminated timber panel systems have been carried out as a part of the full research program on the seismic behavior of these types of wooden systems, realized by Institute of Earthquake Engineering and Engineering Seismology, Skopje, and the Faculty of Civil and Geodetic Engineering (UL FCG), University of Ljubljana. Two different specimens built of cross-laminated timber panels have been tested: specimen containing a pair of single-unit principal wall elements (Specimen 1) and specimen containing a pair of two-unit principal wall elements (Specimen 2). In this article, the results from the shaking-table tests obtained for Specimen 2 and numerically verified by using appropriate finite element method–based computational model are discussed. Reference is also made to the comparative analysis of the test results obtained for both specimens. One of the most important aspects of the research has been the estimation of the seismic energy-dissipation ability of Specimen 1 and 2, via calculation of the equivalent viscous damping using the performed experimental tests. It is generally concluded that Specimen 2 exhibits a similar rocking behavior as Specimen 1, with similar energy-dissipation ability. Both specimens have manifested slightly different dynamic properties, mostly because Specimen 2 has been designed with one anchor more compared to Specimen 1. Forced vibration tests have been used for identification of the effective stiffness on the contacts for Specimen 2. This research is expected to be a contribution toward clarification of the behavior and practical design of cross-laminated timber panel systems subjected to earthquake loading.

Theoretical and Experimental Studies on Reduction for Multi-Modal Seismic Responses of High-Rise Structures by Tuned Liquid Dampers

2004 ◽  
Vol 10 (7) ◽  
pp. 1041-1056 ◽  
Author(s):  
Hong-Nan Li ◽  
Ying Jia ◽  
Su-Yan Wang
Keyword(s):  
Passive Control ◽  
Equations Of Motion ◽  
Experimental Studies ◽  
Tall Buildings ◽  
Shaking Table ◽  
Earthquake Ground Motion ◽  
Seismic Responses ◽  
High Rise ◽  
Tuned Liquid Dampers ◽  
Liquid Dampers

This paper focuses on the use of multiple tuned liquid dampers (TLDs) as passive control devices to reduce the multi-modal responses of tall buildings and high-rise structures to earthquake ground motion excitation. A model of a three-story building with one and two TLDs was installed on a shaking-table. The system was subjected to three earthquake time histories. Then, the mechanical models and the equations of motion for the systems of tall buildings and high-rise structures with TLDs are established. Here, the solution of the dynamic liquid pressure is based on the method of the volume of fluid and the seismic responses are obtained by use of the state equation. The comparisons show that theoretical results are generally in good agreement with experiments. It is observed that the approach presented in this paper has proved to be quite effective both in the numerical example and in the seismic simulating tests.

Experimental Test and Numerical Analysis of a Structure Equipped with a Multi-Tuned Liquid Damper Subjected to Dynamic Loading

2020 ◽  
Vol 20 (07) ◽  
pp. 2050075
Author(s):  
Bui Pham Duc Tuong ◽  
Phan Duc Huynh
Keyword(s):  
Shaking Table ◽  
Tuned Liquid Damper ◽  
Lumped Mass ◽  
Tuned Liquid Dampers ◽  
Lumped Mass Method ◽  
Dynamic Loadings ◽  
Coupling Equations ◽  
Liquid Dampers ◽  
Volume Method ◽  
Simplified Calculation

Tuned liquid dampers (TLDs) have many advantages in controlling building vibrations, among which multi-tuned liquid dampers (MTLDs) appear to have better stability and effectiveness. However, the tank wall was assumed to be rigid in the past by ignoring the fluid-structure interaction (FSI) at the interface, resulting in simplified calculation for the design of the TLDs. Moreover, the fluid in the tank was considered to be separate from the structure. This paper presents two numerical methods to control the responses of the frame under the dynamic loadings: (1) the lumped mass method for quickly designing the TLDs, and (2) the finite volume method/finite element method (FVM/FEM) for analyzing the fluid and solid domains of the TLDs in a single computational 3D model. In addition, the multi-field interaction between the structure-fluid-tank walls is considered by solving the coupling equations at the interfaces. A steel frame is fitted with an MTLD and tested experimentally on a shaking table to investigate its dynamic response. Numerical results are verified with the experimental ones, which show good agreement.

Experimental Verifications on Seismic Response Control of Tall Structures by Multiple Tuned Liquid Dampers

2004 ◽  
Author(s):  
Hong-Nan Li ◽  
Ying Jia ◽  
Su-Yan Wang
Keyword(s):  
Passive Control ◽  
Equations Of Motion ◽  
Tall Buildings ◽  
State Equation ◽  
Shaking Table ◽  
Earthquake Ground Motion ◽  
High Rise ◽  
Tuned Liquid Dampers ◽  
Tall Structures ◽  
Liquid Dampers

The focus of this paper is on the use of multiple Tuned Liquid Dampers (TLDs) as passive control devices to reduce the multi-modal responses of tall buildings and high-rise structures to earthquake ground motion excitation. A model of a 3-story building with one and two TLDs was installed on a shaking-table. The system was subjected to three earthquake time histories. Then the mechanical models and the equations of motion for the systems of tall buildings and high-rise structures with TLDs are established. Here, the solution of the dynamic liquid pressure is based on the method of the Volume of Fluid and the seismic responses are obtained by use of the state equation. The comparisons show that theoretical results are generally in good agreement with experiments. It is observed that the approach presented in this paper proved to be quite effective both in the numerical example and in the seismic simulating tests.

Equivalent mechanical models of tuned liquid dampers with different tank geometries

2008 ◽  
Vol 35 (10) ◽  
pp. 1088-1101 ◽  
Author(s):  
X. Deng ◽  
M. J. Tait
Keyword(s):  
Mechanical Properties ◽  
Effective Mass ◽  
Virtual Work ◽  
Damping Ratio ◽  
Tuned Liquid Damper ◽  
Equivalent Viscous Damping ◽  
Tuned Liquid Dampers ◽  
Mechanical Models ◽  
Sloshing Mode ◽  
Liquid Dampers

This paper focuses on the development of equivalent mechanical models for tuned liquid dampers (TLDs) with rectangular, vertical-cylindrical, horizontal-cylindrical, and hyperboloid (conical) tank shapes under external excitation in the transverse direction. Potential flow theory is utilized to obtain the free-surface response amplitude and the corresponding velocity of the sloshing liquid and Lagrange’s equations are used to determine the generalized properties. Morison’s equation and the virtual work method are used to estimate an equivalent viscous damping ratio based on the screen loss coefficient. The equivalent mechanical properties derived in this paper model the fundamental sloshing mode only and are restricted to small response amplitudes. Subsequently, the equivalent mechanical properties including effective mass, natural frequency, and damping ratio of the TLDs, having different tank geometries, are compared. It is found that the effective mass values for horizontal-cylindrical and hyperboloid TLDs are larger than the effective mass values for vertical-cylindrical and rectangular TLDs. The increased effective mass values for horizontal-cylindrical and hyperboloid TLDs can result in improved tuned liquid damper performance given the same total liquid mass as that of rectangular or vertical-cylindrical TLDs.

Experimental and Numerical Modal Identification of the Fossanova Gothic Cathedral

2007 ◽  
Vol 347 ◽  
pp. 351-358 ◽  
Author(s):  
Gianfranco de Matteis ◽  
I. Langone ◽  
Fabio Colanzi ◽  
Federico M. Mazzolani
Keyword(s):  
Seismic Vulnerability ◽  
Dynamic Behaviour ◽  
Shaking Table Test ◽  
Mediterranean Area ◽  
Modal Identification ◽  
Shaking Table ◽  
Ambient Vibration ◽  
Dynamic Features ◽  
Ambient Vibration Tests ◽  
Vibration Tests

This paper focuses on the dynamic behaviour of the Fossanova cathedral (Latina, ITALY), which represents a magnificent example of pre-Gothic style church, whose structural typology is largely present in the Mediterranean area, especially in many Countries characterised by a High-Medium seismic hazard. In particular, within the European research project PROHITECH, aiming at investigating the seismic vulnerability of such a structural typology, experimental and numerical analyses have been carried out. Firstly, detailed investigations have been devoted to the identification of the geometry of the main constructional parts as well as of the mechanical features of the constituting materials of the cathedral. Then, both Ambient Vibration Tests (AVT) and Numerical Modal Identification analyses by Finite Element Method (FEM) have been applied, allowing the detection of the main dynamic features. Finally, a refined FEM model reproducing the dynamic behaviour of the cathedral by using scaled physical quantities according to the Buckingham theorem has been developed. In fact, the present study has to be intended as a preliminary activity devoted to se up a shaking table test on a reduced scale physical model of Fossanova cathedral, which will be shortly carried out at the IZIIS laboratory (Skopje, Macedonia).

scholarly journals Experimental Studies of Single-Layer Reticulated Domes with Isolated Supports

2018 ◽  
Vol 2018 ◽  
pp. 1-15 ◽  
Author(s):  
Guibo Nie ◽  
Kun Liu
Keyword(s):  
Seismic Behavior ◽  
Damping Ratio ◽  
Experimental Studies ◽  
Three Dimensional ◽  
Single Layer ◽  
Shaking Table ◽  
Dynamic Responses ◽  
Shaking Table Tests ◽  
Isolation Effects ◽  
Reticulated Domes

To study the seismic behavior of a single-layer reticulated dome subjected to severe earthquakes, a series of shaking table tests were conducted for this paper. Seismic responses including the acceleration, displacement, and strains gathered at the members and nodes were discussed. The dynamic characteristics, including structure frequencies and damping ratio, were obtained through the results under the input excitation of white noise and the fast sine sweeping with different amplitudes. Various isolation devices usually installed in the upper portion of the structures have been widely used to reduce the dynamic responses for more than three decades. However, these isolation devices deal mostly with either horizontal isolation or vertical isolation, which is not applicable for synchronous isolation in both horizontal and vertical isolation. Therefore, an innovative isolated support for three-dimensional isolation was invented. In order to understand the earthquake-isolation effects of a single-layer reticulated dome with the isolated support, a series of shaking table tests were conducted. The dynamic behavior of the structure was then investigated and discussed using the acceleration and displacement responses of the tested structures with or without the isolated supports. The experimental results show that the isolated support invented in this study had a remarkable earthquake-isolation action in both horizontal and vertical isolation.

scholarly journals Study on Seismic Performance of a Mold Transformer through Shaking Table Tests

2020 ◽  
Vol 10 (1) ◽  
pp. 361 ◽  
Author(s):  
Ngoc Hieu Dinh ◽  
Seung-Jae Lee ◽  
Joo-Young Kim ◽  
Kyoung-Kyu Choi
Keyword(s):  
Shaking Table Test ◽  
Damping Ratio ◽  
Time History ◽  
Relative Displacement ◽  
Shaking Table ◽  
Shaking Table Tests ◽  
Acceleration Time ◽  
Boundary Limit ◽  
Acceleration Time Histories ◽  
Operational Test

This study presents an experimental seismic investigation of a 1000 kVA cast resin-type hybrid mold transformer through tri-axial shaking table tests. The input acceleration time histories were generated in accordance with the specifications recommended by the International Code Council Evaluation Services Acceptance Criteria ICC-ES AC156 code, with scaling factors in the range of 25–300%. The damage and the dynamic characteristics of the mold transformer were evaluated in terms of the fundamental frequency, damping ratio, acceleration time history responses, dynamic amplification factors, and relative displacement. The shaking table test results showed that the damage of the mold transformer was mainly governed by the severe slippage of the spacers and the loosening of the linked bolts between the bottom beam and the bed beam. In addition, the maximum relative displacement at the top beam in Y and Z-directions exceeded the boundary limit recommended by the Korean National Radio Research Agency. Moreover, the operational test of the specimen was performed based on the IEC 60076-11 Standard before and after the shaking table test series to ensure the operational capacity of the transformer.

scholarly journals Dynamic Modification and Damage Propagation of a Two-Storey Full-Scale Masonry Building

2019 ◽  
Vol 2019 ◽  
pp. 1-21 ◽  
Author(s):  
Leonidas Alexandros S. Kouris ◽  
Andrea Penna ◽  
Guido Magenes
Keyword(s):  
State Space ◽  
Damping Ratio ◽  
Modal Identification ◽  
Shaking Table ◽  
Ambient Vibration ◽  
Masonry Building ◽  
Actual Performance ◽  
Modal Characteristics ◽  
Accumulated Damage ◽  
Modal Damping

The progressive change of modal characteristics due to accumulated damage on an unreinforced masonry (URM) building is investigated. The stone URM building, submitted to five consecutive shakings, has been experimentally studied on the shaking table of EUCENTRE laboratory (Pavia, Italy). The dynamic characteristics of the test specimen are analytically estimated using frequency and state-space modal identification from ambient vibration stationary tests carried out before the strong motion transient tests at various levels of damage. A singular value (SV) decomposition of the cross-correlation matrix of the acceleration response in the frequency domain is applied to determine the modal characteristics. In the time domain, the subspace state-space system identification is performed. Modal characteristics evolve from the initial linear state up to the ultimate collapse state in correlation with accumulated damage. Modal frequencies shorten with increasing intensity, whereas modal damping ratios are enhanced. Modal shapes also change with increasing level of accumulated damage. Comparing the evolution of modal characteristics, it is concluded that modal damping ratio shift can be better correlated with the system’s actual performance giving a better representation of damage than that of natural frequency shift ratio or the modes difference.

Sign in / Sign up

Export Citation Format

Share Document