scholarly journals Mechanical vibration responses of snow samples near the melting temperature

2004 ◽  
Vol 38 ◽  
pp. 130-134 ◽  
Author(s):  
Iwao Takei ◽  
Norikazu Maeno
Keyword(s):  
Elastic Wave ◽  
Young’S Modulus ◽  
Melting Temperature ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Temperature Cycling ◽  
Poisson's Ratio ◽  
Wave Velocities ◽  
Ice Particles ◽  
Snow Samples

AbstractMechanical properties of snow were investigated by means of a vibration response technique in a frequency range from 10Hz to 1MHz and a temperature range from –15° to –0.1°C with heating and cooling processes. The response signals were divided into two kinds of propagation, transverse and longitudinal waves through the snow sample. The temperature dependence of elastic-wave velocities showed a large decrease above –0.6°C. Poisson’s ratio and Young’s modulus of snow samples were derived from the longitudinal and transverse wave velocities. Poisson’s ratio of snow samples showed a value of 0.35 ± 0.01 below –0.6°C, and dropped to 0.29 or less at –0.1°C. Young’s modulus of snow samples at –0.1°C showed values seven-tenths as large as (25–34%less than) those below –0.6°C. These phenomena suggest weakening and slipping of boundaries between ice particles in snow samples near the melting temperature. The elastic-wave velocities and Young’s modulus change with the density of samples and with time and temperature cycling. These changes are related to the number and state of bonds between ice particles in snow samples.

SONIC DETERMINATION OF THE ELASTIC PROPERTIES OF ICE

1947 ◽  
Vol 25a (2) ◽  
pp. 88-95 ◽  
Author(s):  
T. D. Northwood
Keyword(s):  
Rayleigh Wave ◽  
Young’S Modulus ◽  
Elastic Properties ◽  
Elastic Waves ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
The Other ◽  
Poisson's Ratio ◽  
Wave Velocities

By measuring the velocity of various types of elastic waves in a solid it is possible to deduce Young's modulus and Poisson's ratio. Longitudinal, extensional, and Rayleigh wave velocities were measured in ice, the first by resonance in a rod and the other two by a pulsing technique. The value obtained for Young's modulus was 9.8 × 1010 dynes per cm.2 and for Poisson's ratio was 0.33.

Determination of Poisson's Ratio of Thin low-k Films using Bidirectional Thermal Expansion Measurement

2006 ◽  
Vol 914 ◽  
Author(s):  
Jiping Ye ◽  
Satoshi Shimizu ◽  
Shigeo Sato ◽  
Nobuo Kojima ◽  
Junnji Noro
Keyword(s):  
Thermal Expansion ◽  
Temperature Gradient ◽  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Silicon Oxide ◽  
Young's Modulus ◽  
Polymer Materials ◽  
Poisson's Ratio ◽  
Thermal Expansion Measurement ◽  
Low K

AbstractA recently developed bidirectional thermal expansion measurement (BTEM) method was applied to different types of low-k films to substantiate the reliability of the Poisson's ratio found with this technique and thereby to corroborate its practical utility. In this work, the Poisson's ratio was determined by obtaining the temperature gradient of the biaxial thermal stress from substrate curvature measurements, the temperature gradient of the whole thermal expansion strain along the film thickness from x-ray reflectivity (XRR) measurements, and reduced modulus of the film from nanoindentation measurements. For silicon oxide-based SiOC film having a thickness of 382.5 nm, the Poisson's ratio, Young's modulus and thermal extension coefficient (TEC) were determined to be Vf = 0.26, αf =21 ppm/K and Ef =9,7 GPa. These data are close to the levels of metals and polymers rather than the levels of fused silicon oxide, which is characterized by Vf = 0.17 and Er = 69.6 GPa. The alkyl component in the silicon oxide-based framework is thought to act as an agent in reducing the modulus and elevating the Poisson's ratio in SiOC low-k materials. In the case of an organic polymer SiLK film with a thickness of 501.5 nm, the Poisson's ratio, Young's modulus and TEC were determined to be Vf = 0.39, αf =74 ppm/K and Er =3.1 GPa, which are in the typical range of V= 0.34~0.47 with E =1.0~10 GPa for polymer materials. From the viewpoint of the relationship between the Poisson's ratio and Young's modulus as classified by different material types, the Poisson's ratios found for the silicon oxide-based SiOC and organic SiLK films are reasonable values, thereby confirming that BTEM is a reliable and effective method for evaluating the Poisson's ratio of thin films.

Measurement of Young's Modulus and Poisson's Ratio of Thin Film by Combination of Bulge Test and Nano-Indentation

2008 ◽  
Vol 33-37 ◽  
pp. 969-974 ◽  
Author(s):  
Bong Bu Jung ◽  
Seong Hyun Ko ◽  
Hun Kee Lee ◽  
Hyun Chul Park
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Young’S Modulus ◽  
Poisson’S Ratio ◽  
Young's Modulus ◽  
Applied Pressure ◽  
Indentation Test ◽  
Poisson's Ratio ◽  
Bulge Test ◽  
Nano Indentation

This paper will discuss two different techniques to measure mechanical properties of thin film, bulge test and nano-indentation test. In the bulge test, uniform pressure applies to one side of thin film. Measurement of the membrane deflection as a function of the applied pressure allows one to determine the mechanical properties such as the elastic modulus and the residual stress. Nano-indentation measurements are accomplished by pushing the indenter tip into a sample and then withdrawing it, recording the force required as a function of position. . In this study, modified King’s model can be used to estimate the mechanical properties of the thin film in order to avoid the effect of substrates. Both techniques can be used to determine Young’s modulus or Poisson’s ratio, but in both cases knowledge of the other variables is needed. However, the mathematical relationship between the modulus and Poisson's ratio is different for the two experimental techniques. Hence, achieving agreement between the techniques means that the modulus and Poisson’s ratio and Young’s modulus of thin films can be determined with no a priori knowledge of either.

Multi-Parameter Optimization to Improve the Erosion Resistance of Coating by Fe Simulation

2021 ◽  
Author(s):  
Fang Li ◽  
Liuxi Cai ◽  
Shun-sen Wang ◽  
Zhenping Feng
Keyword(s):  
Tensile Stress ◽  
Young’S Modulus ◽  
Impact Velocity ◽  
Coating Thickness ◽  
Poisson’S Ratio ◽  
Erosion Resistance ◽  
Young's Modulus ◽  
Tio2 Coating ◽  
Poisson's Ratio ◽  
Stress Peak

Abstract Finite element method (FEM) was used to study the stress peak of stress S11 (Radial stress component in X-axis) on the steam turbine blade surface of four typical erosion-resistant coatings (Fe2B, CrN, Cr3C2-NiCr and Al2O3-13%TiO2). The effect of four parameters, such as impact velocity, coating thickness, Young's modulus and Poisson's ratio on the stress peak of stress S11 were analyzed. Results show that: the position of tensile stress peak and compressive stress peak of stress S11 are far away from the impact center point with the increase of impact velocity. When coating thickness is equal to or greater than 10μm, the magnitude of tensile stress peak of stress S11 on the four coating surfaces does not change with the coating thickness at different impact velocities. When coating thickness is equal to or greater than 2μm, the magnitude of tensile stress peak of stress S11 of four coatings show a trend of increasing first and then decreasing with the increase of Young's modulus. Meanwhile, the larger the Poisson's ratio, the smaller the tensile stress peak of stress S11. After optimization, When coating thickness is 2μm, Poisson's ratio is 0.35 and Young's modulus is 800 GPa, the Fe2B coating has the strongest erosion resistance under the same impact conditions, followed by Cr3C2-NiCr, CrN, and the Al2O3- 13%TiO2 coating, Al2O3-13%TiO2 coating has the worst erosion resistance.

Sign in / Sign up

Export Citation Format

Share Document