Application of nano-PCMs in solar Photovoltaic

2020 ◽  
pp. 47-58
Author(s):  
Shubham Srivastava ◽  
Deepak ◽  
CS Malvi
Keyword(s):  
Transfer Rate ◽  
Open Circuit Voltage ◽  
Open Circuit ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Storage Medium ◽  
Pv System ◽  
Cooling Systems ◽  
Pv Panel ◽  
Solar Pv System

Although the good intensity of solar radiation is desirable for a solar PV system, but the power output drops with a rise in its temperature. The open-circuit voltage of PV panel decreases with increase in its temperature, thus lowering the PV effect. Many studies have been carried out by the researcher to tackle this problem, proposing modification in conventional PV system design and utilizing water, air, PCM, and oil as a cooling medium in various cooling systems. Although PCM has fascinating characteristics as a thermal energy storage medium in the solar system, but low thermal conductivity became a barrier in energy conversion. Few studies suggested the use of nanoparticles in PCM to increase its heat transfer rate but very few studies were focused on nano PCM incorporated solar PV system. This paper summarized the researches done so far on nano PCM solar PV system by delineating the methods, and materials involved.

scholarly journals Design of Augmented Cooling System for Urban Solar PV System

2021 ◽  
Vol 335 ◽  
pp. 03002
Author(s):  
Chong Jia Joon ◽  
Kelvin Chew Wai Jin
Keyword(s):  
Cooling System ◽  
Electrical Energy ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Pv System ◽  
Pv Panel ◽  
Solar Pv System ◽  
Low Efficiency ◽  
Electrical Loads ◽  
Temperature Output

Solar photovoltaic (PV) panels have been widely used to convert the renewable energy from the sun to electrical energy to power electrical loads but suffers from relatively low efficiency between 15% to 22%. Typically, the panels have an average lifespan of 25 to 30 years but could degrade quicker due to the panel overheating. Beyond the optimum working temperature of 25°C, a drop of efficiency by 0.4 to 0.5% for every 1°C had been reported. For solar PV applications in urban regions, passive cooling is beneficial due to limited amount of space and lower energy consumption compared to active cooling. A solar PV system with augmented cooling was conducted at a balcony of a condominium from 10am until 2pm. The solar PV system consisted of an Arduino controller, solar panel module, temperature sensor and LCD monitor. Reusable cold and hot gel packs were attached to the bottom of the solar PV. Both setups of solar PV panel with and without the cooling system were placed at the balcony simultaneously for measurement of temperature, output voltage and current. From this research, the outcome of implementing a cooling system to the solar PV increases the efficiency of the energy conversion.

Grid Parity of Residential Building Rooftop Solar PV in India

2021 ◽  
pp. 19-40
Author(s):  
Rakesh Dalal ◽  
Kamal Bansal ◽  
Sapan Thapar
Keyword(s):  
Residential Building ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Indian Government ◽  
Pv System ◽  
Pv Systems ◽  
Grid Parity ◽  
Solar Pv System ◽  
Utility Grid ◽  
Rooftop Solar

Rooftop solar photovoltaic(PV) installation in India have increased in last decade because of the flat 40 percent subsidy extended for rooftop solar PV systems (3 kWp and below) by the Indian government under the solar rooftop scheme. From the residential building owner's perspective, solar PV is competitive when it can produce electricity at a cost less than or equal grid electricity price, a condition referred as “grid parity”. For assessing grid parity of 3 kWp and 2 kWp residential solar PV system, 15 states capital and 19 major cities were considered  for the RET screen simulation by using solar isolation, utility grid tariff, system cost and other economic parameters. 3 kWp and 2 kWp rooftop solar PV with and without subsidy scenarios were considered for simulation using RETscreen software. We estimate that without subsidy no state could achieve grid parity for 2kWp rooftop solar PV plant. However with 3 kWp rooftop solar PV plant only 5 states could achieve grid parity without subsidy and with government subsidy number of states increased to 7, yet wide spread parity for residential rooftop solar PV is still not achieved. We find that high installation costs, subsidized utility grid supply to low energy consumer and financing rates are major barriers to grid parity.

Modeling and Optimization of Solar PV System With Pumped Hydro Energy Storage System

2021 ◽  
pp. 147-185
Keyword(s):  
Energy Storage ◽  
Storage System ◽  
Economic Cost ◽  
Energy Storage System ◽  
Solar Pv ◽  
Pv System ◽  
Modeling And Optimization ◽  
Pv Panel ◽  
Cost Of Energy ◽  
Solar Pv System

Implementation of modified AHP coupled with MOORA methods for modeling and optimization of solar photovoltaic (PV)-pumped hydro energy storage (PHS) system parameter is presented in this chapter. Work optimized the parameters, namely unmet energy (UE), size of PV-panel, and volume of upper reservoir (UR), to get economic cost of energy (COE) and excess energy (EE). The trail no.11 produces the highest assessment values compared to the other trails and provides EE as 16.19% and COE as 0.59 $/kWh for PV-PHS. ANOVA and parametric study is also performed to determine the significance of the parameters for PV-PHS performance. Investigation results indicate the effectiveness and significant potential for modeling and optimization of PV-PHS system and other solar energy systems.

scholarly journals New Design of Solar Photovoltaic and Thermal Hybrid System for Performance Improvement of Solar Photovoltaic

2020 ◽  
Vol 2020 ◽  
pp. 1-6
Author(s):  
Ridwone Hossain ◽  
Al Jumlat Ahmed ◽  
Sheik Md Kazi Nazrul Islam ◽  
Nirupam Saha ◽  
Preetom Debnath ◽  
...  
Keyword(s):  
Hybrid Systems ◽  
Energy Conversion Efficiency ◽  
Open Circuit ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Thermal Systems ◽  
Energy Technologies ◽  
Pv Panel ◽  
Average Improvement ◽  
New Type

Solar photovoltaic (PV) and solar thermal systems are most widely used renewable energy technologies. Theoretical study indicates that the energy conversion efficiency of solar photovoltaic gets reduced about 0.3% when its temperature increases by 1°C. In this regard, solar PV and thermal (PVT) hybrid systems could be a solution to draw extra heat from the solar PV panel to improve its performance by reducing its temperature. Here, we have designed a new type of heat exchanger for solar PV and thermal (PVT) hybrid systems and have studied the performance of the system. The PVT system has been investigated in comparison with an identical solar PV panel at outdoor condition at Dhaka, Bangladesh. The experiments show that the average improvement of open circuit voltage (Voc) is 0.97 V and the highest improvement of Voc is 1.3 V. In addition, the overall improvement of output power of solar PV panel is 2.5 W.

scholarly journals Impact of Soiling Rate on Solar Photovoltaic Panel in Malaysia

2018 ◽  
Vol 225 ◽  
pp. 04008 ◽  
Author(s):  
Shaharin A. Sulaiman ◽  
M. Rosman M. Razif ◽  
Tan Dei Han ◽  
Samson M. Atnaw ◽  
S. Norazilah A. Tamili
Keyword(s):  
Prediction Model ◽  
Electrical Power ◽  
Time Interval ◽  
Solar Pv ◽  
Pv System ◽  
Photovoltaic Panel ◽  
Pv Panel ◽  
Time Period ◽  
Solar Pv System ◽  
Time Basis

There are some weaknesses of using solar PV system especially when there is issue of soiling on the surface of solar PV panel. The consequences for absence of this such study can cause unanticipated cost in the operation of solar PV panel. The objective of this project is to study the trend of soiling rate over different time period and its effect on the performance of solar PV panel in Malaysia and to develop a simple prediction model for cleaning interval of solar PV system in Malaysia. The study was conducted on real-time basis on a building’s roof. Measurements of solar irradiance, voltage, current and the mass of dust collected were performed from both clean and dirty panels. It was discovered that the Monthly Test was significant with 4.53% of performance drop. Further analysis was conducted by running prediction model for cleaning interval. Intersection of graph plotting and fixed cleaning cost gives answer of cleaning interval that can be performed. It can be concluded that for every two and half month is the recommended time interval to perform regular cleaning to maximise electrical power generation by solar PV system in Malaysia.

scholarly journals Improved Fractional Open Circuit Voltage MPPT Methods for PV Systems

Electronics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 321 ◽  
Author(s):  
Dmitry Baimel ◽  
Saad Tapuchi ◽  
Yoash Levron ◽  
Juri Belikov
Keyword(s):  
Open Circuit Voltage ◽  
Open Circuit ◽  
Maximum Power ◽  
Pv System ◽  
Maximum Power Point ◽  
Pv Systems ◽  
Point Tracking ◽  
Pv Panel ◽  
Power Point Tracking ◽  
Power Point

This paper proposes two new Maximum Power Point Tracking (MPPT) methods which improve the conventional Fractional Open Circuit Voltage (FOCV) method. The main novelty is a switched semi-pilot cell that is used for measuring the open-circuit voltage. In the first method this voltage is measured on the semi-pilot cell located at the edge of PV panel. During the measurement the semi-pilot cell is disconnected from the panel by a pair of transistors, and bypassed by a diode. In the second Semi-Pilot Panel method the open circuit voltage is measured on a pilot panel in a large PV system. The proposed methods are validated using simulations and experiments. It is shown that both methods can accurately estimate the maximum power point voltage, and hence improve the system efficiency.

scholarly journals Solar Concentrators In Malaysia: Towards The Development Of Low Cost Solar Photovoltaic Systems

2012 ◽  
Author(s):  
Firdaus Muhammad Sukki ◽  
Roberto Ramirez Iniguez ◽  
Scott G. Mcmeekin ◽  
Brian G. Stewart ◽  
Barry Clive
Keyword(s):  
Financial Analysis ◽  
Low Cost ◽  
Good Alternative ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Financial Benefit ◽  
Pv System ◽  
Solar Concentrators ◽  
Pv Systems ◽  
Solar Pv System

Solar energy has become a matter of global attention in the past few years. This paper explores the use and benefit of solar concentrators in the solar photovoltaic (PV) systems. First, a short literature review of previous research on the usage of solar concentrators in improving solar PV system performance and reducing the cost of implementation is presented. This is followed by an overview of SolarBrane, an example of a Building Integrated photovoltaic (BIPV) system which uses an optical concentrator in the solar PV design. An optimised design of the SolarBrane is also discussed afterwards. A financial benefit study is conducted to compare the average return of investment of using the optimised SolarBrane and traditional solar PV installed in Malaysia’s environment. SolarBrane has proven to be a good alternative to achieve costeffective solar PV system. The financial analysis simulated under the new Malaysian Feed–In Tariff scheme indicates that the optimised SolarBrane could potentially reduce the initial cost of implementation by 40% and generate higher return, close to 20%, when compared to traditional solar PV systems. Key words: Solar photovoltaic; solar concentrator; solarBrane; dielectric totally internally reflecting concentrator; financial analysis

scholarly journals Solar Photovoltaic Power Prediction Using Big Data Tools

2021 ◽  
Vol 13 (24) ◽  
pp. 13685
Author(s):  
Mariz B. Arias ◽  
Sungwoo Bae
Keyword(s):  
Big Data ◽  
Prediction Model ◽  
Solar Irradiance ◽  
Weather Data ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
Power Prediction ◽  
Pv System ◽  
Generation Planning ◽  
Solar Pv System

Solar photovoltaic (PV) installation has been continually growing to be utilized in a grid-connected or stand-alone network. However, since the generation of solar PV power is highly variable because of different factors, its accurate forecasting is critical for a reliable integration to the grid and for supplying the load in a stand-alone network. This paper presents a prediction model for calculating solar PV power based on historical data, such as solar PV data, solar irradiance, and weather data, which are stored, managed, and processed using big data tools. The considered variables in calculating the solar PV power include solar irradiance, efficiency of the PV system, and characteristics of the PV system. The solar PV power profiles for each day of January, which is a summer season, were presented to show the variability of the solar PV power in numerical examples. The simulation results show relatively accurate forecasting with 17.57 kW and 2.80% as the best root mean square error and mean relative error, respectively. Thus, the proposed solar PV power prediction model can help power system engineers in generation planning for a grid-connected or stand-alone solar PV system.

scholarly journals Feasibility Study of Grid-Connected Solar Photovoltaic (PV) System for Primary School in Johor

2018 ◽  
Vol 11 (1) ◽  
pp. 233
Author(s):  
Siti Amely Jumaat ◽  
Adhwa Amsyar Syazwan Ab Majid ◽  
Chin Kim Gan ◽  
Mohd Noor Abdullah ◽  
Nur Hanis Radzi ◽  
...  
Keyword(s):  
Educational Institution ◽  
Project Planning ◽  
Solar Photovoltaic ◽  
Solar Pv ◽  
System Implementation ◽  
Huge Amount ◽  
Pv System ◽  
Pv Module ◽  
Solar Pv System ◽  
The Cost

This project aims to determine the potential of grid connected solar Photovoltaic (PV) implementation and project planning of solar PV System in school.  Generally, the educational institution used huge amount of electricity to operate so their monthly bills is expensive. Therefore, the project planning is necessary to determine the potential of solar PV system implementation. The project planning consists of the current electricity consumed by the school and the amount of 120W Monocrystalline PV module needed by them. The cost of project are determines to identify the initial cost of this project implementation. Lastly, analysis on the profit collected by SK Pintas Raya after 20 years of solar PV system implementation proved the importance of this project.

Sign in / Sign up

Export Citation Format

Share Document