scholarly journals Rapidly-Dissolving silver-containing bioactive glasses for cariostatic applications

2021 ◽  
Author(s):  
Omar Rodríguez ◽  
Adel M.F. Alhalawani ◽  
Saad Arshad ◽  
Mark R. Towler

A novel bioactive glass series containing incremental amounts of silver oxide was synthesized, ground down, and subsequently incorporated into a dentifrice for the purpose of reducing the incidence of dental caries and lesion formation. Three glasses were synthesized using the melt quench route: Si-Control (70SiO2–12CaO–3P2O5–15Na2O, mol %), Si-02 and Si-05, where 0.2 and 0.5 mol % Ag2O were substituted, respectively, for SiO2 in Si-Control. The glasses were then ground, sieved, characterized, and dissolved in Tris buffer solution (pH = 7.30) for 6, 12, and 24 h, with the pH of the resultant solution being recorded and the ions that were released into solution quantified. Samples of each glass were subsequently embedded into a non-fluoridated, commercially available toothpaste which was then used to brush resin-mounted lamb molars which, up to the point of testing, had been stored in a 1.0 M HCl solution. Knoop microhardness measurements of the molars were recorded before and after brushing to determine the presence of remineralization on the surface of the teeth (surface hardness loss of 37%, 35%, and 34% for Si-Control, Si-02 and Si-05, respectively, after 24 h). Four oral cavity bacterial strains were isolated through swabs of the inner cheek, gums, and teeth surfaces of three volunteers, and placed on agar discs. Of each glass, 0.5 g was placed onto the discs, and the resultant inhibition zones were measured after 6, 12, and 24 h. Si-05 performed better than Si-02 on two strains after 24 h, while exhibiting similar behavior for the remaining two strains after 24 h; the largest inhibition zone measured was 2.8 mm, for Si-05 after 12 h. Si-Control exhibited no antibacterial effect at any time point, providing evidence for the role of silver oxide as the antibacterial component of these glasses.

2021 ◽  
Author(s):  
Omar Rodríguez ◽  
Adel M.F. Alhalawani ◽  
Saad Arshad ◽  
Mark R. Towler

A novel bioactive glass series containing incremental amounts of silver oxide was synthesized, ground down, and subsequently incorporated into a dentifrice for the purpose of reducing the incidence of dental caries and lesion formation. Three glasses were synthesized using the melt quench route: Si-Control (70SiO2–12CaO–3P2O5–15Na2O, mol %), Si-02 and Si-05, where 0.2 and 0.5 mol % Ag2O were substituted, respectively, for SiO2 in Si-Control. The glasses were then ground, sieved, characterized, and dissolved in Tris buffer solution (pH = 7.30) for 6, 12, and 24 h, with the pH of the resultant solution being recorded and the ions that were released into solution quantified. Samples of each glass were subsequently embedded into a non-fluoridated, commercially available toothpaste which was then used to brush resin-mounted lamb molars which, up to the point of testing, had been stored in a 1.0 M HCl solution. Knoop microhardness measurements of the molars were recorded before and after brushing to determine the presence of remineralization on the surface of the teeth (surface hardness loss of 37%, 35%, and 34% for Si-Control, Si-02 and Si-05, respectively, after 24 h). Four oral cavity bacterial strains were isolated through swabs of the inner cheek, gums, and teeth surfaces of three volunteers, and placed on agar discs. Of each glass, 0.5 g was placed onto the discs, and the resultant inhibition zones were measured after 6, 12, and 24 h. Si-05 performed better than Si-02 on two strains after 24 h, while exhibiting similar behavior for the remaining two strains after 24 h; the largest inhibition zone measured was 2.8 mm, for Si-05 after 12 h. Si-Control exhibited no antibacterial effect at any time point, providing evidence for the role of silver oxide as the antibacterial component of these glasses.


2021 ◽  
Author(s):  
Saad Arshad

In this study, bioactive glasses were designed for the purposes of reducing the incidence of dental caries and lesion formation by supplying the teeth with therapeutic ions which may support remineralization and provide an antibacterial effect against oral cavity bacteria. Three glasses were synthesised through the melt quench method: Si-Control (SiO2-CaO-P2O5-Na2O), Si-02 and Si-05, where 0.2% and 0.5% Ag2O were substituted, respectively, for SiO2 in the control glass. The glasses were then ground, characterized and dissolved in tris buffer solution (pH=7.30) for 6, 12 and 24 hours, with the pH rise of the solution being recorded (7.48 for Si-Control, and 7.66 for both Si-02 and Si-05 after 24 hours) and the ions that were released into the tris buffer solution quantified. Samples of each glass were subsequently embedded into non-fluoridated toothpaste and samples of the paste were used to brush resin-mounted lamb molars after a 1.0M HCl overnight demineralization challenge. Knoop microhardness measurements were recorded before and after brushing to determine the presence of remineralization on the surface of the teeth (Percent Surface Hardness Loss of 37%, 35% and 34% for Si-Control, Si-02 and Si-05 respectively after 24 hours). Four oral cavity bacterial strains were isolated through swabs of the inner cheek, gums and teeth surfaces of three volunteers, and placed on agar discs. 0.5g of each glass were placed onto the discs and the resultant inhibition zones were measured after 6, 12 and 24 hours. Si-05 consistently performed better than Si-02 on all strains and timeframes, while Si-Control exhibited no antibacterial effect at any time point.


2021 ◽  
Author(s):  
Saad Arshad

In this study, bioactive glasses were designed for the purposes of reducing the incidence of dental caries and lesion formation by supplying the teeth with therapeutic ions which may support remineralization and provide an antibacterial effect against oral cavity bacteria. Three glasses were synthesised through the melt quench method: Si-Control (SiO2-CaO-P2O5-Na2O), Si-02 and Si-05, where 0.2% and 0.5% Ag2O were substituted, respectively, for SiO2 in the control glass. The glasses were then ground, characterized and dissolved in tris buffer solution (pH=7.30) for 6, 12 and 24 hours, with the pH rise of the solution being recorded (7.48 for Si-Control, and 7.66 for both Si-02 and Si-05 after 24 hours) and the ions that were released into the tris buffer solution quantified. Samples of each glass were subsequently embedded into non-fluoridated toothpaste and samples of the paste were used to brush resin-mounted lamb molars after a 1.0M HCl overnight demineralization challenge. Knoop microhardness measurements were recorded before and after brushing to determine the presence of remineralization on the surface of the teeth (Percent Surface Hardness Loss of 37%, 35% and 34% for Si-Control, Si-02 and Si-05 respectively after 24 hours). Four oral cavity bacterial strains were isolated through swabs of the inner cheek, gums and teeth surfaces of three volunteers, and placed on agar discs. 0.5g of each glass were placed onto the discs and the resultant inhibition zones were measured after 6, 12 and 24 hours. Si-05 consistently performed better than Si-02 on all strains and timeframes, while Si-Control exhibited no antibacterial effect at any time point.


2014 ◽  
Vol 1058 ◽  
pp. 323-328
Author(s):  
Xin Yi Zhao ◽  
Shao Jie Hou ◽  
Shi Bao Li

Purpose To investigate the cariostatic effect of six restorative materials in vitro. Method Enamel blocks of bovine incisors were restored with six restorative materials (a conventional GIC, FujiIILC, Compoglass F, BeautifilII,Charisma and an experimental fluoride releasing resin composite) respectively with a gap of 270μm in width between each filling material and enamel. Then all restorations were immersed in a partially saturated acidic buffer solution at 37C for 3days. The surface enamel microhardness of the enamel blocks were measured before and after demineralization and the depth of enamel demineralization was measured using polarization microscope for each restoration.Results Enamel surface hardness of all restorations demonstrated significant reduced after demineralization ( p<0.05), and the order of hardness reduction is as follows: Charisma >BeautifilII≈Compoglass F≈Experimental Resin>FujiIILC>GIC ( p> 0.05). The order of the depth of enamel demineralization along the surface and the interface near the gap for the 5 materials is as follows: Charisma >BeautifilII≈Compoglass F ≈Experimental Resin>FujiIILC>GIC (P > 0.05). Conclusion The new fluoride releasing and recharging composite resin has the ability to prevent recurrent caries around the restoration and its ability is comparable to compomer materials.


Clay Minerals ◽  
2015 ◽  
Vol 50 (1) ◽  
pp. 11-22 ◽  
Author(s):  
D. Krajišnik ◽  
A. Daković ◽  
A. Malenović ◽  
M. Kragović ◽  
J. Milić

AbstractThe sorption of ibuprofen by modified natural zeolite composites at three concentration levels (10, 20 and 30 mmol/100 g) of cationic surfactants – benzalkonium chloride and cetylpyridinium chloride, in a buffer solution (pH 7.4), was studied. Characterization of the composites before and after ibuprofen sorption was performed by drug sorption and isotherm studies, zeta potential and Fourier Transform infrared spectroscopic analysis. The biopharmaceutical performance of cationic surfactant-modified zeolites as drug formulation excipients was evaluated by in vitro dissolution experiments from the composites with medium surfactant contents. The drug sorption was influenced by the surfactant type and amount used for the zeolite modification. Prolonged drug release over a period of 8 h (up to ~40%) was achieved with both groups of samples. The kinetic analysis showed that the drug release profiles were best fitted with the Higuchi and the Bhaskar models, indicating a combination of drug diffusion and ion exchange as the predominant release mechanisms.


1993 ◽  
Vol 58 (3) ◽  
pp. 547-554 ◽  
Author(s):  
Hyman H. Rehan ◽  
Said A. Salih ◽  
Hassan El-Daley ◽  
Ahmed G. Gad-Allah

The corrosion behaviour of mild steel was investigated in acidic acetate buffer solution using impendance and potential measurements. It was found that there are two dissolution rates resulting from the duplex nature of the formed oxides. The dissolution rates were found to depend on the dissolving acetate buffer solution pH and the dissolution temperature. In all cases, the film thickness was found to decrease with time of corrosion according to the relation Cm-1 = (Cm0)-1 - kdt1/2. It was found that addition of sulfide ions increases the dissolution rate and increases the rate of hydrogen evolution reaction but does not affect the mechanism of cathodic process. The role of sulfide ions on the corrosion behaviour of steel in acetate buffer solutions is revealed by the complex plane impendance analysis.


2016 ◽  
Vol 1 (2) ◽  
pp. 47-54
Author(s):  
La Agus

The study aims to determine the effect of fermentation time complete feed and silage of Tebon corn to changes in pH and nutrient content. This research was conducted in January to March 2015, in the Laboratory airy College of Agricultural Sciences (STIPER) Kendari and analysis of feed materials to be carried out at the Laboratory of Animal Nutrition and Feed Faculty of Animal Husbandry Haluoleo university. Materials used in this study were aged 60-70 days corn Tebon, pollard 20%; copra 20%; premix 30%; corn Empok 25%; salt 2.5%; minerals 2.5%, Aquadest, a buffer solution pH 7. The catalyst, concentrated H2SO4, distilled water, 0,1N H2SO4, NaOH 40%, indicatormix, 0,1N NaOH. Equipment used in this study include: chopper, plastic, rope scales, vacuum, freezer, Erlenmeyer, pH meter, analytical balance, pumpkin Kjeldhal, Erlenmeyer, glass beaker, destructor, distillation, titration tools, ovens and furnaces. The method used in this study is completely randomized design experiment Nested with 2 treatments, three long storage and 3 replicates (2x3x3) on each treatment. The treatment tested was: Concentrate + Tebon corn with different fermentation time, concentrate + corn silage Tebon with different fermentation time, then do Silage-making, mixing Silage, Silage Testing. The parameters in this study the degree of acidity (pH), nutrient content includes dry matter (DM), organic matter (OM) and crude protein (CP) before and after fermentation. Based on the results of complete feed nutrient content analysis showed that each - each fermentation time treatment effect (P<0,01) to change the content of DM, OM and CP when compared to the control with the average low enough pH ranged from 4.18 to 4, 38. Based on this research can be concluded that the fermentation time very real impact on the quality of corn silage Tebon. Fermentation feed concentrate and corn Tebon (KT) decreased nutrient content higher than the complete feed made from concentrates and corn Tebon silage (KS)


Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1114 ◽  
Author(s):  
Shirmendagva Darisuren ◽  
Jeong-Hyeon Park ◽  
Young-Sik Pyun ◽  
Auezhan Amanov

In this study, the effects of ultrasonic nanocrystal surface modification (UNSM) technology on the fatigue life of needle roller bearings were investigated. The fatigue life of the untreated and UNSM-treated needle roller bearings was evaluated using a roller fatigue tester at various contact stress levels, under oil lubrication conditions. It was found that the fatigue life of the UNSM-treated needle roller bearing was extended by approximately 34.3% in comparison with the untreated one. The results of the surface roughness and surface hardness of the needle roller bearings before and after UNSM technology were compared and discussed in order to understand the role of UNSM technology in improving fatigue life. It was found that the application of UNSM technology to the needle roller bearings can improve their fatigue life by reducing the friction coefficient and increasing the wear resistance, which may be attributed to the reduction in surface roughness from 0.50 µm to 0.15 µm and also the increase in surface hardness from 58 HRC to 62 HRC.


2021 ◽  
Vol 11 (23) ◽  
pp. 11330
Author(s):  
Doina Prodan ◽  
Marioara Moldovan ◽  
Gabriel Furtos ◽  
Codruța Saroși ◽  
Miuța Filip ◽  
...  

Various powders of graphene oxide (GO), GO with silver (GO-Ag) and zinc oxide (GO-ZnO) were obtained. The powders were silanized with (3-aminopropyl) triethoxysilane (APTES) aiming to be used, in a future stage, as additives in the hydraulic lime mortars composition. The powders were characterized by Fourier Transform Infrared Spectrometry (FTIR) and Scanning Electron Microscopy (SEM) before and after the silanization process. GO, GO-Ag, GO-Ag-APTES, GO-ZnO and GO-ZnO-APTES powders were also investigated by Thermogravimetric Analysis (TG/DTA) and Ultraviolet–Visible Spectroscopy (UV-Vis). Likewise, the antibacterial effect of powders against five bacterial strains was evaluated. The peaks associated to the functional groups from GO, GO-APTES, GO-Ag, GO-Ag-APTES, GO-ZnO and GO-ZnO-APTES powders were identified by FTIR analysis. The mass losses of powders, analyzed by TG/DTA were lower than those recorded for GO. By UV-VIS analysis, maxima corresponding to the electronic π-π * and n-π * transitions were recorded. SEM images highlighted the lamellar and layered structure of GO, but also the presence of Ag and Zn nanoparticles on the surface of graphene sheets. All these results confirm the presence of Ag/ZnO/APTES on the GO. The antibacterial effect evaluated by recording the diameter of the inhibition zone ranged between 12–22 mm.


Crisis ◽  
2010 ◽  
Vol 31 (3) ◽  
pp. 160-164 ◽  
Author(s):  
Almir Fajkic ◽  
Orhan Lepara ◽  
Martin Voracek ◽  
Nestor D. Kapusta ◽  
Thomas Niederkrotenthaler ◽  
...  

Background: Evidence on youth suicides from Southeastern Europe is scarce. We are not aware of previous reports from Bosnia and Herzegovina, which experienced war from 1992 to 1995. Durkheim’s theory of suicide predicts decreased suicide rates in wartime and increased rates afterward. Aims: To compare child and adolescent suicides in Bosnia and Herzegovina before and after the war. Methods: Data on youth suicide for prewar (1986–90) and postwar (2002–06) periods were analyzed with respect to prevalence, sex and age differences, and suicide methods. Suicide data from 1991 through 2001 were not available. Results: Overall youth suicide rates were one-third lower in the postwar than in the prewar period. This effect was most pronounced for girls, whose postwar suicide rates almost halved, and for 15–19-year-old boys, whose rates decreased by about a one-fourth. Suicides increased among boys aged 14 or younger. Firearm suicides almost doubled proportionally and were the predominant postwar method, while the most common prewar method had been hanging. Conclusions: The findings from this study indicate the need for public education in Bosnia and Herzegovina on the role of firearm accessibility in youth suicide and for instructions on safe storage in households. Moreover, raising societal awareness about suicide risk factors and suicide prevention is needed.


Sign in / Sign up

Export Citation Format

Share Document