scholarly journals Combined building integrated photovoltaic-thermal collector with air source heat pump for cold climate

2021 ◽  
Author(s):  
Raghad Sabah Kamel
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Electricity Consumption ◽  
Test Facility ◽  
Air Source Heat Pump ◽  
Building Integrated Photovoltaic ◽  
In Series ◽  
T System

A TRNSYS model was developed to conduct a comprehensive study of combining a building integrated photovoltaic thermal (BIPV/T) collector with an air source heat pump (ASHP) in an Archetype Sustainable House. The heat pump uses the warm air generated in the BIPV/T as the source for heat production. The coupling of BIPV/T and ASHP enables a highly efficient heating system in winter conditions. A numerical model was developed for an air-based PV/T collector. The model was used to predict the thermal and electrical performance of the collector and to conduct a comprehensive analysis for different configurations (number of PV/T panels in rows NR and in series NS) and different design parameters. TRNSYS simulation results showed that low air mass flow rate and low duct depth enhance the heat pump coefficient of performance (COP). The arrangement with a large number of PV/T systems connected in series has higher COP. The maximum obtained seasonal heating COP was 3.45, corresponding to duct depth of 1.5 in, NS=5 and low row mass flow rate of 0.03 kg/s. The heat pump cumulative electricity consumption for a typical heating season could be reduced by 20.2%. When the analysis was based only on sunny hours, the electricity consumption of the combined ASHP + PV/T system was reduced by 52% and the predicted seasonal COP of the heat pump was 5.98. A new full-scale test facility was presented to be implemented at Toronto and Region Conservation Authority to examine the performance of combining passive system and dynamic building envelope technologies (BIPV/T+ASHP+TES) under real weather conditions. It is important to match the maximum airflow for the BIPV/T system with the maximum airflow for the outdoor coil of the heat pump. The pressure drop inside the PV/T collector along with the connecting air duct from the BIPV/T to ASHP for a wide range of airflow rates and different duct depths was calculated. It was found that for air a flow rate around 2000 CFM, which is the maximum CFM for the custom-made ASHP for the test facility, the predicted fan energy was 195 kWh/year corresponding to 1.5 in. duct depth.

scholarly journals Combined building integrated photovoltaic-thermal collector with air source heat pump for cold climate

2021 ◽  
Author(s):  
Raghad Sabah Kamel
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Electricity Consumption ◽  
Test Facility ◽  
Air Source Heat Pump ◽  
Building Integrated Photovoltaic ◽  
In Series ◽  
T System

A TRNSYS model was developed to conduct a comprehensive study of combining a building integrated photovoltaic thermal (BIPV/T) collector with an air source heat pump (ASHP) in an Archetype Sustainable House. The heat pump uses the warm air generated in the BIPV/T as the source for heat production. The coupling of BIPV/T and ASHP enables a highly efficient heating system in winter conditions. A numerical model was developed for an air-based PV/T collector. The model was used to predict the thermal and electrical performance of the collector and to conduct a comprehensive analysis for different configurations (number of PV/T panels in rows NR and in series NS) and different design parameters. TRNSYS simulation results showed that low air mass flow rate and low duct depth enhance the heat pump coefficient of performance (COP). The arrangement with a large number of PV/T systems connected in series has higher COP. The maximum obtained seasonal heating COP was 3.45, corresponding to duct depth of 1.5 in, NS=5 and low row mass flow rate of 0.03 kg/s. The heat pump cumulative electricity consumption for a typical heating season could be reduced by 20.2%. When the analysis was based only on sunny hours, the electricity consumption of the combined ASHP + PV/T system was reduced by 52% and the predicted seasonal COP of the heat pump was 5.98. A new full-scale test facility was presented to be implemented at Toronto and Region Conservation Authority to examine the performance of combining passive system and dynamic building envelope technologies (BIPV/T+ASHP+TES) under real weather conditions. It is important to match the maximum airflow for the BIPV/T system with the maximum airflow for the outdoor coil of the heat pump. The pressure drop inside the PV/T collector along with the connecting air duct from the BIPV/T to ASHP for a wide range of airflow rates and different duct depths was calculated. It was found that for air a flow rate around 2000 CFM, which is the maximum CFM for the custom-made ASHP for the test facility, the predicted fan energy was 195 kWh/year corresponding to 1.5 in. duct depth.

Experimental Investigation on Flow Characteristic of Stepped Capillary Tube for Heat Pump Type Air Conditioner with R410A

2014 ◽  
Vol 960-961 ◽  
pp. 643-647
Author(s):  
Yan Sheng Xu
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Capillary Tube ◽  
Coefficient Of Performance ◽  
Tube Length ◽  
Air Conditioner ◽  
Capillary Tubes ◽  
Tube Assembly

A stepped capillary tube consisting of two serially connected capillary tubes with different diameters is invented to replace the conventional expansion device. The mass flow rate of refrigerant R410A in stepped capillary tubes with different size were tested. The model of stepped capillary tube is proposed, and its numerical algorithm for tube length and mass flow rate is developed. The experimental results show that the performance comparing between stepped capillary tube system and capillary tube assembly system, the cooling capacity is reduced by 0.3%, the energy efficiency ratio (EER) is equal to each other, the heating capacity is increased by 0.3%, the coefficient of performance (COP) is decreased by 0.3%. That is to say, the performance index of the two kinds of throttle mechanism is almost identical. It indicates that the stepped capillary tube can replace the capillary tube assembly in the R410A heat pump type air conditioner absolutely. The model is validated with experimental data, and the results show that the model can be used for sizing and rating stepped capillary tube.

Receiver Outlet Temperature Control for Falling Particle Receiver Applications

2021 ◽  
Author(s):  
Nathan Schroeder ◽  
Henk Laubscher ◽  
Brantley Mills ◽  
Clifford K. Ho
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Temperature Rise ◽  
Pid Controller ◽  
Input Parameter ◽  
Slide Gate ◽  
Process Variable ◽  
Test Facility ◽  
Outlet Temperature

Abstract Falling particle receivers (FPRs) are being studied in concentrating solar power applications to enable high temperatures for supercritical CO2 (sCO2) Brayton power cycles. The falling particles are introduced into the cavity receiver via a linear actuated slide gate and irradiated by concentrated sunlight. The thickness of the particle curtain associated with the slide-gate opening dimension dictates the mass flow rate of the particle curtain. A thicker, higher mass flow rate, particle curtain would typically be associated with a smaller temperature rise through the receiver, and a thinner, lower mass flow rate, particle curtain would result in a larger temperature rise. Using the receiver outlet temperature as the process variable and the linear actuated slide gate as the input parameter a proportional, integral, and derivative (PID) controller was implemented to control the temperature of the particles leaving the receiver. The PID parameters were tuned to respond in a quick and stable manner. The PID controlled slide gate was tested using the 1 MW receiver at the National Solar Thermal Test Facility (NSTTF). The receiver outlet temperature was ramped from ambient to 800°C then maintained at the setpoint temperature. After reaching a steady-state, perturbations of 15%–20% of the initial power were applied by removing heliostats to simulate passing clouds. The PID controller reacted to the change in the input power by adjusting the mass flow rate through the receiver to maintain a constant receiver outlet temperature. A goal of ±2σ ≤ 10°C in the outlet temperature for the 5 minutes following the perturbation was achieved.

Design and Testing of a Can Combustor for a Small Gas Turbine Application

2013 ◽  
Author(s):  
K. V. L. Narayana Rao ◽  
N. Ravi Kumar ◽  
G. Ramesha ◽  
M. Devathathan
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Turbines ◽  
Pressure Loss ◽  
High Energy ◽  
Experimental Results ◽  
High Mass ◽  
Test Facility ◽  
Design Requirements

Can type combustors are robust, with ease of design, manufacturing and testing. They are extensively used in industrial gas turbines and aero engines. This paper is mainly based on the work carried out in designing and testing a can type combustion chamber which is operated using JET-A1 fuel. Based on the design requirements, the combustor is designed, fabricated and tested. The experimental results are analysed and compared with the design requirements. The basic dimensions of the combustor, like casing diameter, liner diameter, liner length and liner hole distribution are estimated through a proprietary developed code. An axial flow air swirler with 8 vanes and vane angle of 45 degree is designed to create a re-circulation zone for stabilizing the flame. The Monarch 4.0 GPH fuel nozzle with a cone angle of 80 degree is used. The igniter used is a high energy igniter with ignition energy of 2J and 60 sparks per minute. The combustor is modelled, meshed and analysed using the commercially available ansys-cfx code. The geometry of the combustor is modified iteratively based on the CFD results to meet the design requirements such as pressure loss and pattern factor. The combustor is fabricated using Ni-75 sheet of 1 mm thickness. A small combustor test facility is established. The combustor rig is tested for 50 Hours. The experimental results showed a blow-out phenomenon while the mass flow rate through the combustor is increased beyond a limit. Further through CFD analysis one of the cause for early blow out is identified to be a high mass flow rate through the swirler. The swirler area is partially blocked and many configurations are analysed. The optimum configuration is selected based on the flame position in the primary zone. The change in swirler area is implemented in the test model and further testing is carried out. The experimental results showed that the blow-out limit of the combustor is increased to a good extent. Hence the effect of swirler flow rate on recirculation zone length and flame blow out is also studied and presented. The experimental results showed that the pressure loss and pattern factor are in agreement with the design requirements.

Analytical Modeling and Experimental Validation of Heating at the Leaf Seal/Rotor Interface

2016 ◽  
Vol 139 (4) ◽  
Author(s):  
Michael J. Pekris ◽  
Gervas Franceschini ◽  
Andrew K. Owen ◽  
Terry V. Jones ◽  
David R. H. Gillespie
Keyword(s):  
Mass Flow Rate ◽  
Analytical Model ◽  
Mass Flow ◽  
Flow Rate ◽  
Temperature Rise ◽  
Thermal Characteristic ◽  
Frictional Heat ◽  
Test Facility ◽  
Engine Operation ◽  
Secondary Air

The secondary air system of a modern gas or steam turbine is configured to satisfy a number of requirements, such as to purge cavities and maintain a sufficient flow of cooling air to key engine components, for a minimum penalty on engine cycle efficiency and specific fuel consumption. Advanced sealing technologies, such as brush seals and leaf seals, are designed to maintain pressures in cavities adjacent to rotating shafts. They offer significant reductions in secondary air parasitic leakage flows over the legacy sealing technology, the labyrinth seal. The leaf seal comprises a series of stacked sheet elements which are inclined relative to the radial direction, offering increased axial rigidity, reduced radial stiffness, and good leakage performance. Investigations into leaf seal mechanical and flow performance have been conducted by previous researchers. However, limited understanding of the thermal behavior of contacting leaf seals under sustained shaft contact has led to the development of an analytical model in this study, which can be used to predict the power split between the leaf and rotor from predicted temperature rises during operation. This enables the effects of seal and rotor thermal growth and, therefore, implications on seal endurance and rotor mechanical integrity to be quantified. Consideration is given to the heat transfer coefficient in the leaf pack. A dimensional analysis of the leaf seal problem using the method of extended dimensions is presented, yielding the expected form of the relationship between seal frictional power generation, leakage mass flow rate, and rotor temperature rise. An analytical model is derived which is in agreement. Using the derived leaf temperature distribution formula, the theoretical leaf tip temperature rise and temperature distributions are computed over a range of mass flow rates and frictional heat values. Experimental data were collected in high-speed tests of a leaf seal prototype using the Engine Seal Test Facility at Oxford University. These data were used to populate the analytical model and collapsed well to confirm the expected linear relationship. In this form, the thermal characteristic can be used with predictions of mass flow rate and frictional power generated to estimate the leaf tip and rotor temperature rise in engine operation.

Thermal Performance Analysis and Optimization of Solar Assisted Heat Pump Water Heater

2014 ◽  
Vol 592-594 ◽  
pp. 2416-2421
Author(s):  
R.N. Kokila ◽  
S. Rajakumar
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Performance ◽  
Optimization Technique ◽  
Direct Expansion ◽  
Water Heater ◽  
Rate Optimization ◽  
Flat Plate Collector

The main objective of this paper is to analyze the thermal performance of direct expansion solar assisted heat pump DX-SAHP(A) by numerical simulation in MATLAB and comparing it with the thermal performance of DX-SAHP(B) which has an optimized collector area and mass flow rate. Optimization is performed for high exergy efficiency using Particle Swarm Optimization (PSO) and Artificial Bee Colony (ABC) optimization technique. The flat plate collector of solar water heater is used as the evaporator with refrigerant (R22).With the optimized value of mass flow rate as 0.055 kg/sec, width as 0.03 m and diameter of riser tubes as 0.021 m the performance of the optimized system has a maximum COP of 6.85 which is greater than the COP of DX-SAHP(A) and the final water temperature of is obtained 100 minutes earlier in the optimized system i.e. DX-SAHP(B) with compressor work less than the system A

Evaluation of Axial Compressor Characteristics Under Overspray Condition

2013 ◽  
Author(s):  
Chihiro Myoren ◽  
Yasuo Takahashi ◽  
Manabu Yagi ◽  
Takanori Shibata ◽  
Tadaharu Kishibe
Keyword(s):  
Gas Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Water Mass ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Test Facility ◽  
Compressor Performance ◽  
Water Mass Flow Rate

An axial compressor was developed for an industrial gas turbine equipped with a water atomization cooling (WAC) system, which is a kind of inlet fogging technique with overspray. The compressor performance was evaluated using a 40MW-class test facility for the advanced humid air turbine system. A prediction method to estimate the effect of WAC was developed for the design of the compressor. The method was based on a streamline curvature (SLC) method implementing a droplet evaporation model. Four test runs with WAC have been conducted since February 2012. The maximum water mass flow rate was 1.2% of the inlet mass flow rate at the 4th test run, while the design value was 2.0%. The results showed that the WAC decreased the inlet and outlet temperatures compared with the DRY (no fogging) case. These decreases changed the matching point of the gas turbine, and increased the mass flow rate and the pressure ratio by 1.8% and 1.1%, respectively. Since prediction results agreed with the results of the test run qualitatively, the compressor performance improvement by WAC was confirmed both experimentally and analytically. The test run with the design water mass flow rate is going to be conducted in the near future.

PV/T Performance Evaluation as Electricity Generation and Hot Air Supplier for Fully and Partially Covered with PV Modules

2020 ◽  
Vol 38 (7A) ◽  
pp. 1001-1015
Author(s):  
Jalal M. Jalil ◽  
Ahmed A. Hussein ◽  
Anwar J. Faisal
Keyword(s):  
Mass Flow Rate ◽  
Air Temperature ◽  
Mass Flow ◽  
Flow Rate ◽  
Fluid Dynamic ◽  
Electrical Power ◽  
Energy System ◽  
Solar Simulator ◽  
Pv Modules ◽  
T System

The solar energy system is environmentally friendly and the utilization of photovoltaic thermal collectors, (PV/T) has attracted more attention, which directly converts solar radiation into electricity and thermal energy simultaneously. This study investigated the air biased Photovoltaic thermal hybrid solar collectors, (PV/T) trend for two cases, denominate case one (PV/T system fully covered with PV modules), and case tow (PV/T system partially covered with glass). The studied parameters were solar irradiance and the air mass flow rate. The investigation has been performed in terms of outlet air temperature, electrical power, thermal and electrical efficiencies. A numerical model was developed using the computational fluid dynamic program (CFD) and the results were compared with the experimental measurements that carried out from indoor conditions using a solar simulator. A good agreement has been achieved between experimental and numerical results. The performance of both cases one and case two concluded that the PV/T system should be operating at a moderate air flow rate of 0.013 kg/s, which is the best mass flow rate. In addition, it has been observed that for case tow the maximum outlet air temperature and electric powers were 44.3 oC and 26.6 W, respectively. For case one, thermal and electrical efficiencies were found 34% and 10%, respectively, based on the experimental data, while for case 2, the maximum thermal and electrical efficiencies were found to be 48.9 and 9.1%, respectively.

scholarly journals Operating characteristics of transcritical CO2 heat pump for simultaneous water cooling and heating

2011 ◽  
Vol 33 (4) ◽  
pp. 23-40 ◽  
Author(s):  
Jahar Sarkar ◽  
Souvik Bhattacharyya
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Water Mass ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Water Cooling ◽  
Operating Characteristics ◽  
Water Mass Flow Rate

Abstract The effects of water-side operating conditions (mass flow rates and inlet temperatures) of both evaporator and gas cooler on the experimental as well as simulated performances (cooling and heating capacities, system coefficient of performance (COP) and water outlet temperatures) of the transcritical CO2 heat pump for simultaneous water cooling and heating the are studied and revised. Study shows that both the water mass flow rate and inlet temperature have significant effect on the system performances. Test results show that the effect of evaporator water mass flow rate on the system performances and water outlet temperatures is more pronounced (COP increases by 0.6 for 1 kg/min) compared to that of gas cooler water mass flow rate (COP increases by 0.4 for 1 kg/min) and the effect of gas cooler water inlet temperature is more significant (COP decreases by 0.48 for given range) compared to that of evaporator water inlet temperature (COP increases by 0.43 for given range). Comparisons of experimental values with simulated results show the maximum deviation of 5% for cooling capacity, 10% for heating capacity and 16% for system COP.

Sign in / Sign up

Export Citation Format

Share Document