scholarly journals Kajian Mikrostruktur dan Dielektrik Nanopartikel MnFe2O4 Yang Disintesis Dengan Metode Kopresipitasi

JURNAL HADRON ◽  
2021 ◽  
Vol 3 (2) ◽  
pp. 30-35
Author(s):  
Rachmad Almi Putra
Keyword(s):  
Manganese Ferrite ◽  
Lcr Meter

Telah dilakukan penelitian sintesis dan karakterisasi nanopartikel manganese ferrite dengan metode kopresipitasi pada suhu rendah yaitu 900C. Tujuan penelitian ini adalah untuk mengetahui pengaruh suhu rendah terhadap microstruktur dan sifat dielektrik pada nanopartikel MnFe2O4. Sintesis nanopartikel dilakukan dengan metode kopresipitasi, karakterisasi menggunakan XRD dan uji sifat dielektrik menggunakan LCR Meter. Data pengukuran XRD diolah mengggunakan Software Origin 9.0. Ukuran kristalit yang diperoleh adalah 5,79 nm pada suhu 90 °C, 5,65 nm pada suhu 120 °C dan 5,47 nm pada suhu 150 °C dengan parameter kisi rata-rata 9,16 Å. Ukuran kristalit dapat terkontrol menggunakan metode sintesis pada suhu rendahNilai dielektrik tertinggi dihasilkan pada suhu 150 °C yaitu 0,41 x 106 dengan nilai kapasitansi 4,59 x 10-8 F. Peningkatan konstanta dielektrik terjadi karena meningkatnya suhu pemanasan oven sedangkan ukuran kristalit yang dihasilkan lebih kecil.

scholarly journals Manganese Ferrite Nanoparticles Encapsulated into Vitamin E/Sphingomyelin Nanoemulsions as Contrast Agents for High‐Sensitive Magnetic Resonance Imaging

2021 ◽  
pp. 2101019
Author(s):  
Sandra Díez‐Villares ◽  
Miguel A. Ramos‐Docampo ◽  
Andrés da Silva‐Candal ◽  
Pablo Hervella ◽  
Abi J. Vázquez‐Ríos ◽  
...  
Keyword(s):  
Magnetic Resonance Imaging ◽  
Vitamin E ◽  
Magnetic Resonance ◽  
Contrast Agents ◽  
Ferrite Nanoparticles ◽  
Manganese Ferrite ◽  
Resonance Imaging

Recovery of manganese from a low-grade waste and valorization via the synthesis of a nanostructured magnetic manganese ferrite

2021 ◽  
Vol 269 ◽  
pp. 115177
Author(s):  
Rojin Eghbali ◽  
Parsa Khanmohammadi Hazaveh ◽  
Fereshteh Rashchi ◽  
Abolghasem Ataie
Keyword(s):  
Low Grade ◽  
Manganese Ferrite

scholarly journals Stereoselective synthesis of spirocyclic pyrrolidines/pyrrolizidines/pyrrolothiazolidines using l-proline functionalized manganese ferrite nanorods as a novel heterogeneous catalyst

RSC Advances ◽  
2021 ◽  
Vol 11 (24) ◽  
pp. 14755-14768
Author(s):  
Malihe Akhavan ◽  
Ahmadreza Bekhradnia
Keyword(s):  
Heterogeneous Catalyst ◽  
Stereoselective Synthesis ◽  
Manganese Ferrite ◽  
One Pot ◽  
New Class

An efficient, green, one-pot, and three-component protocol has been reported for the stereoselective synthesis of a new class of spiro thiazolidines.

Plasticizer effect on dielectric properties of poly(methyl methacrylate)/titanium dioxide composites

2021 ◽  
pp. 096739112110147
Author(s):  
Ufuk Abaci ◽  
H Yuksel Guney ◽  
Mesut Yilmazoglu
Keyword(s):  
Dielectric Constant ◽  
Titanium Dioxide ◽  
Dielectric Properties ◽  
Methyl Methacrylate ◽  
Pure Pmma ◽  
Segmental Mobility ◽  
Scanning Calorimetry ◽  
Poly Methyl Methacrylate ◽  
Casting Technique ◽  
Lcr Meter

The effect of plasticizer on dielectric properties of poly(methyl methacrylate) (PMMA)/titanium dioxide (TiO2) composites was investigated. Propylene carbonate (PC) was used as plasticizer in the samples which were prepared with the conventional solvent casting technique. Scanning Electron Microscopy with Energy Dispersive X-Ray Analysis (SEM-EDX) and Differential scanning calorimetry (DSC) analyses and LCR Meter measurements (performed between 300 K and 400 K), were conducted to examine the properties of the composites. With the addition of plasticizer, the thermal properties have changed and the dielectric constant of the composite has increased significantly. The glass transition temperature of pure PMMA measured 121.7°C and this value did not change significantly with the addition of TiO2, however, 112°C was measured in the sample with the addition 4 ml of PC. While the dielectric constant of pure PMMA was 3.64, the ε′ value increased to 5.66 with the addition of TiO2 and reached 12.6 with the addition of 4 ml PC. These changes have been attributed to increase in amorphous ratio that facilitates polymer dipolar and segmental mobility.

scholarly journals Optimization of manganese ferrite/distilled water parameter design on heat exchanger using RSM and CFD

2021 ◽  
Vol 1034 (1) ◽  
pp. 012056
Author(s):  
Avita Ayu Permanasari ◽  
Muhammad Taufiq Affandi ◽  
Sukarni ◽  
Poppy Puspitasari ◽  
Mirza Abdillah
Keyword(s):  
Heat Exchanger ◽  
Parameter Design ◽  
Distilled Water ◽  
Manganese Ferrite

Effect of Calcinations on Characterizations of Fabricated Nano Manganese Ferrite

2013 ◽  
Vol 634-638 ◽  
pp. 2150-2154 ◽  
Author(s):  
Rita Sundari ◽  
Tang Ing Hua ◽  
M. Rusli Yosfiah
Keyword(s):  
Sol Gel ◽  
Volatile Components ◽  
Manganese Ferrite ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reflectance Analysis ◽  
Transmission Electron Microscope Analysis ◽  
Electron Microscope Analysis ◽  
Nano Size

A citric acid anionic surfactant has been applied for nano manganese ferrite (MnFeO3) fabrication using sol gel method. The calcinations have been varied for 300, 600 and 800oC. The UVDR (UV-Vis Diffused Reflectance) analysis shows a high absorptive band gap after 400 nm for the 600oC calcinated MnFeO3. The DTA (Differential Thermal Analysis) profiles exhibit remarkably trapped volatile matters (H2O, CO2, and NO2) in the fabricated MnFeO3 under sol gel heat treatment at 100oC and the peaks disappeared as the calcination increased to 600oC. As the temperature elevated from 100 to 300oC, the absorption peaks of volatile components are disappeared as demonstrated clearly by the FTIR (Fourier Transform Infrared) spectra of the fabricated material, which 3393 cm-1 corresponded to OH group, 1624 cm-1 to CO group, and 1384 cm-1 to NO group. The XRD (X-Ray Diffraction) spectra show clearly the alteration process from amorphous to crystalline structure as the calcinations increased from 300 to 600oC. In addition, the TEM (Transmission Electron Microscope) analysis exhibits parts of the fabricated MnFeO3 found in cubic nano size of 15-40 nm under interested calcinations and the result is in agreement with that obtained by XRD investigation.

scholarly journals Thermal, Structural, and Physical Properties of Freeze Dried Tropical Fruit Powder

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
K. A. Athmaselvi ◽  
C. Kumar ◽  
M. Balasubramanian ◽  
Ishita Roy
Keyword(s):  
Particle Size ◽  
Physical Properties ◽  
Average Particle Size ◽  
Average Particle ◽  
X Ray Diffraction ◽  
Tropical Fruit ◽  
X Ray ◽  
Freeze Dried ◽  
Fruit Powder ◽  
Lcr Meter

This study evaluates the physical properties of freeze dried tropical (guava, sapota, and papaya) fruit powders. Thermal stability and weight loss were evaluated using TGA-DSC and IR, which showed pectin as the main solid constituent. LCR meter measured electrical conductivity, dielectric constant, and dielectric loss factor. Functional groups assessed by FTIR showed presence of chlorides, and O–H and N–H bonds in guava, chloride and C–H bond in papaya, and chlorides, and C=O and C–H bonds in sapota. Particle size and type of starch were evaluated by X-ray diffraction and microstructure through scanning electronic microscopy. A semicrystalline profile and average particle size of the fruit powders were evidenced by X-ray diffraction and lamellar/spherical morphologies by SEM. Presence of A-type starch was observed in all three fruits. Dependence of electric and dielectric properties on frequency and temperature was observed.

Sign in / Sign up

Export Citation Format

Share Document