scholarly journals Improving the Performance of Drilling Fluid Using Lignite Nano Particles

2019 ◽  
Vol 26 (1) ◽  
pp. 100-105
Author(s):  
Ghufran Falih ◽  
Nada S. Al-Zubaidi ◽  
Asawer A. Al-Wasiti
Keyword(s):  
High Temperature ◽  
Salt Water ◽  
Drilling Fluid ◽  
Nano Particles ◽  
Drilling Fluids ◽  
Mud Cake ◽  
Different Temperatures ◽  
Good Filtration ◽  
Water Base ◽  
Nanoparticle Additives

The effect of lignite on the filtration characteristics of water base mud was studied at low and high temperature. Recently, the nanoparticle additives are studied and investigated as alternative additives due to its stability during drilling even at high-temperature and high-pressure (HTHP) conditions. In this study the effect of nano particles size of Lignite on filtrate volume and mud cake thickness was investigated , at different weights (0.01, 0.05, 0.07, 0.1, and 0.2) gm, in (API WBM, Polymer mud, DURA THERM mud, and Saturated Salt Water mud) and different temperatures (35, 75, and 100) oC. The results show that most tests provided a very good filtration control for the used drilling fluids at 100 oC. Better performances were observed in polymer and Saturated Salt Water mud at 100 oC with Lignite concentration of 0.01 gm and 0.1 gm, and filtrate volume reduction 52.5 % and 60 % respectively.

scholarly journals Synthesis of a Novel Filtrate Reducer and Its Application in Water-Based Drilling Fluid for Ultra-High-Temperature Reservoirs

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Dongyu Qiao ◽  
Zhongbin Ye ◽  
Lei Tang ◽  
Yiping Zheng ◽  
Xindong Wang ◽  
...  
Keyword(s):  
Particle Size ◽  
High Temperature ◽  
Adsorption Capacity ◽  
Fresh Water ◽  
Drilling Fluid ◽  
Salt Resistance ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Water Based ◽  
Water Base

The high-temperature stability and filtration property controlling of ultra-high-temperature water-based drilling fluids is a worldwide problem. To resolve this problem, a high-temperature-resistant quaternary copolymer (HTRTP) was synthesized based on molecular structure optimization design and monomer optimization. The physical and chemical properties were characterized by infrared spectroscopy, thermal weight, and spectrophotometry, and their temperature and salt resistance was evaluated in different drilling fluids, combined with adsorption, particle size analysis, and stability test. The results show that the thermal stability of HTRTP is very strong, and the initial temperature of thermal decomposition is above 320°C. The salt resistance of HTRTP is more than 162 g/L, and the calcium resistance is more than 5000 mg/L, which is equivalent to the foreign temperature-resistant polymer DCL-a, and is superior to the domestic metal ion viscosity increasing fluid loss agent PMHA-II for drilling fluids. It has excellent high-temperature resistance (245°C) and fluid loss reduction effect in fresh water base mud, fresh water weighted base mud, saturated brine base mud, and composite salt water base mud, which is better than foreign DCL-a (245°C) and domestic PMHA (220°C). The adsorption capacity of HTRTP on clay particles is large and firm, and the adsorption capacity changes little under the change of chemical environment and temperature. Both before and after HTRTP aging (245°C/16 h), the permeability of filter cake can be significantly reduced and its compressibility can be improved. By optimizing the particle size gradation of the drilling fluid and enhancing the colloid stability of the system, HTRTP can improve the filtration building capacity of the drilling fluid and reduce the filtration volume. The development of antithermal polymer provides a key treatment agent for the study of anti-high-temperature-resistant saline-based drilling fluid.

scholarly journals Thermoresponsive Bentonite for Water-Based Drilling Fluids

Materials ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2115 ◽  
Author(s):  
Dong ◽  
Pu ◽  
Ren ◽  
Zhai ◽  
Gao ◽  
...  
Keyword(s):  
High Temperature ◽  
Drilling Fluid ◽  
Environmental Scanning Electron Microscopy ◽  
High Density ◽  
Drilling Fluids ◽  
Isothermal Adsorption ◽  
Mud Cake ◽  
Water Based ◽  
Recovery Behavior ◽  
Increasing Temperature

As an important industrial material, bentonite has been widely applied in water-based drilling fluids to create mud cakes to protect boreholes. However, the common mud cake is porous, and it is difficult to reduce the filtration of a drilling fluid at high temperature. Therefore, this paper endowed bentonite with a thermo response via the insertion of N-isopropylacrylamide (NIPAM) monomers. The interaction between NIPAM monomers and bentonite was investigated via Fourier infrared spectroscopy (FTIR), isothermal adsorption, and X-ray diffraction (XRD) at various temperatures. The results demonstrate that chemical adsorption is involved in the adsorption process of NIPAM monomers on bentonite, and the adsorption of NIPAM monomers accords with the D–R model. With increasing temperature, more adsorption water was squeezed out of the composite when the temperature of the composite exceeded 70 °C. Based on the composite of NIPAM and bentonite, a mud cake was prepared using low-viscosity polyanionic cellulose (Lv-PAC) and initiator potassium peroxydisulfate (KPS). The change in the plugging of the mud cake was investigated via environmental scanning electron microscopy (ESEM), contact angle testing, filtration experiments, and linear expansion of the shale at various temperatures. In the plugging of the mud cake, a self-recovery behavior was observed with increasing temperature, and resistance was observed at 110 °C. The rheology of the drilling fluid was stable in the alterative temperature zone (70–110 °C). Based on the high resistance of the basic drilling fluid, a high-density drilling fluid (ρ = 2.0 g/cm3) was prepared with weighting materials with the objective of drilling high-temperature formations. By using a high-density drilling fluid, the hydration expansion of shale was reduced by half at 110 °C in comparison with common bentonite drilling fluid. In addition, the rheology of the high-density drilling fluid tended to be stable, and a self-recovery behavior was observed.

scholarly journals Experimental Investigation of the Rheological Behavior of an Oil-Based Drilling Fluid with Rheology Modifier and Oil Wetter Additives

Molecules ◽  
2021 ◽  
Vol 26 (16) ◽  
pp. 4877
Author(s):  
Mobeen Murtaza ◽  
Sulaiman A. Alarifi ◽  
Muhammad Shahzad Kamal ◽  
Sagheer A. Onaizi ◽  
Mohammed Al-Ajmi ◽  
...  
Keyword(s):  
High Temperature ◽  
Zeta Potential ◽  
Hot Rolling ◽  
Emulsion Stability ◽  
Drilling Fluid ◽  
Temperature Tolerance ◽  
Fluid Loss ◽  
Drilling Fluids ◽  
Before And After ◽  
Rheology Modifier

Drilling issues such as shale hydration, high-temperature tolerance, torque and drag are often resolved by applying an appropriate drilling fluid formulation. Oil-based drilling fluid (OBDF) formulations are usually composed of emulsifiers, lime, brine, viscosifier, fluid loss controller and weighting agent. These additives sometimes outperform in extended exposure to high pressure high temperature (HPHT) conditions encountered in deep wells, resulting in weighting material segregation, high fluid loss, poor rheology and poor emulsion stability. In this study, two additives, oil wetter and rheology modifier were incorporated into the OBDF and their performance was investigated by conducting rheology, fluid loss, zeta potential and emulsion stability tests before and after hot rolling at 16 h and 32 h. Extending the hot rolling period beyond what is commonly used in this type of experiment is necessary to ensure the fluid’s stability. It was found that HPHT hot rolling affected the properties of drilling fluids by decreasing the rheology parameters and emulsion stability with the increase in the hot rolling time to 32 h. Also, the fluid loss additive’s performance degraded as rolling temperature and time increased. Adding oil wetter and rheology modifier additives resulted in a slight loss of rheological profile after 32 h and maintained flat rheology profile. The emulsion stability was slightly decreased and stayed close to the recommended value (400 V). The fluid loss was controlled by optimizing the concentration of fluid loss additive and oil wetter. The presence of oil wetter improved the carrying capacity of drilling fluids and prevented the barite sag problem. The zeta potential test confirmed that the oil wetter converted the surface of barite from water to oil and improved its dispersion in the oil.

Improving the rheological properties of water-based calcium bentonite drilling fluids using water-soluble polymers in high temperature applications

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Jinliang Liu ◽  
Fengshan Zhou ◽  
Fengyi Deng ◽  
Hongxing Zhao ◽  
Zhongjin Wei ◽  
...  
Keyword(s):  
High Temperature ◽  
Rheological Properties ◽  
Apparent Viscosity ◽  
Drilling Fluid ◽  
Shear Thickening ◽  
Water Soluble ◽  
Drilling Fluids ◽  
Drilling Depth ◽  
Filtration Loss ◽  
Calcium Bentonite

Abstract Most of bentonite used in modern drilling engineering is physically and chemically modified calcium bentonite. However, with the increase of drilling depth, the bottom hole temperature may reach 180 °C, thus a large amount of calcium bentonite used in the drilling fluid will be unstable. This paper covers three kinds of calcium bentonite with poor rheological properties at high temperature, such as apparent viscosity is greater than 45 mPa·s or less than 10 mPa·s, API filtration loss is greater than 25 mL/30 min, which are diluted type, shear thickening type and low-shear type, these defects will make the rheological properties of drilling fluid worse. The difference is attributed to bentonite mineral composition, such as montmorillonite with good hydration expansion performance. By adding three kinds of heat-resistant water-soluble copolymers Na-HPAN (hydrolyzed polyacrylonitrile sodium), PAS (polycarboxylate salt) and SMP (sulfomethyl phenolic resin), the rheological properties of calcium bentonite drilling fluids can be significantly improved. For example, the addition of 0.1 wt% Na-HPAN and 0.1 wt% PAS increased the apparent viscosity of the XZJ calcium bentonite suspension from 4.5 to 19.5 mPa·s at 180 °C, and the filtration loss also decreased from 20.2 to 17.8 mL.

Well Clean-Up Using a Combined Thermochemical/Chelating Agent Fluids

2019 ◽  
Vol 141 (10) ◽  
Author(s):  
Mohamed Mahmoud
Keyword(s):  
High Temperature ◽  
Filter Cake ◽  
Oil And Gas ◽  
Drilling Fluid ◽  
Chelating Agent ◽  
Drilling Fluids ◽  
Gas Wells ◽  
Oil And Gas Wells ◽  
Different Types ◽  
Cake Removal

The well clean-up process involves the removal of impermeable filter cake from the formation face. This process is essential to allow the formation fluids to flow from the reservoir to the wellbore. Different types of drilling fluids such as oil- and water-based drilling fluids are used to drill oil and gas wells. These drilling fluids are weighted with different weighting materials such as bentonite, calcium carbonate, and barite. The filter cake that forms on the formation face consists mainly of the drilling fluid weighting materials (around 90%), and the rest is other additives such as polymers or oil in the case of oil-base drilling fluids. The process of filter cake removal is very complicated because it involves more than one stage due to the compatibility issues of the fluids used to remove the filter cake. Different formulations were used to remove different types of filter cake, but the problem with these methods is the removal efficiency or the compatibility. In this paper, a new method was developed to remove different types of filter cakes and to clean-up oil and gas wells after drilling operations. Thermochemical fluids that consist of two inert salts when mixed together will generate very high pressure and high temperature in addition to hot water and hot nitrogen. These fluids are sodium nitrate and ammonium chloride. The filter cake was formed using barite and calcite water- and oil-based drilling fluids at high pressure and high temperature. The removal process started by injecting 500 ml of the two salts and left for different time periods from 6 to 24 h. The results of this study showed that the newly developed method of thermochemical removed the filter cake after 6 h with a removal efficiency of 89 wt% for the barite filter cake in the water-based drilling fluid. The mechanisms of removal using the combined solution of thermochemical fluid and ethylenediamine tetra-acetic acid (EDTA) chelating agent were explained by the generation of a strong pressure pulse that disturbed the filter cake and the generation of the high temperature that enhanced the barite dissolution and polymer degradation. This solution for filter cake removal works for reservoir temperatures greater than 100 °C.

Characterization of the Rheological Behavior of Drilling Fluids

2020 ◽  
Author(s):  
Eric Cayeux ◽  
Amare Leulseged
Keyword(s):  
Shear Rate ◽  
Rheological Behavior ◽  
Drilling Fluid ◽  
Drilling Fluids ◽  
Shear Rates ◽  
Operation Conditions ◽  
Fluid Systems ◽  
Different Temperatures ◽  
The One ◽  
Shear Stress Response

Abstract It is nowadays well accepted that the steady state rheological behavior of drilling fluids must be modelled by at least three parameters. One of the most often used models is the yield power law, also referred as the Herschel-Bulkley model. Other models have been proposed like the one from Robertson-Stiff, while other industries have used other three-parameter models such as the one from Heinz-Casson. Some studies have been made to compare the degree of agreement between different rheological models and rheometer measurements but in most cases, already published works have only used mechanical rheometers that have a limited number of speeds and precision. For this paper, we have taken measurements with a scientific rheometer in well-controlled conditions of temperature and evaporation, and for relevant shear rates that are representative to normally encountered drilling operation conditions. Care has been made to minimize the effect of thixotropy on measurements, as the shear stress response of drilling fluids depends on its shear history. Measurements have been made at different temperatures, for various drilling fluid systems (both water and oil-based), and with variable levels of solid contents. Also, the shear rate reported by the rheometer itself, is corrected to account for the fact that the rheometer estimates the wall shear rate on the assumption that the tested fluid is Newtonian. A measure of proximity between the measurements and a rheological model is defined, thereby allowing the ranking of different rheological behavior model candidates. Based on the 469 rheograms of various drilling fluids that have been analyzed, it appears that the Heinz-Casson model describes most accurately the rheological behavior of the fluid samples, followed by the model of Carreau, Herschel-Bulkley and Robertson-Stiff, in decreasing order of fidelity.

scholarly journals Utilization of metakaolin-based geopolymer as a mud-cake solidification agent to enhance the bonding strength of oil well cement–formation interface

2020 ◽  
Vol 7 (2) ◽  
pp. 191230
Author(s):  
Yuhuan Bu ◽  
Rui Ma ◽  
Jiapei Du ◽  
Shenglai Guo ◽  
Huajie Liu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Bonding Strength ◽  
Oil And Gas ◽  
Drilling Fluid ◽  
Research Work ◽  
Drilling Fluids ◽  
Oil Well ◽  
Mud Cake ◽  
Calculation Methodology ◽  
Zonal Isolation

This research work designed a novel mud-cake solidification method to improve the zonal isolation of oil and gas wells. The calculation methodology of mud-cake compressive strength was proposed. The optimal formula of activator and solid precursors, the proper activating time and the best activator concentration were determined by the compressive strength test. The effects of solid precursors on the properties of drilling fluid were evaluated. Test results show that the respective percentage of bentonite, metakaolin, slag and activator is 1 : 1 : 0.3 : 0.8, as well as the optimum ratio of Na 2 SiO 3 /NaOH is 40 : 1. The optimum concentration of activator is 0.21 and the activating time should be more than 10 min. The solid precursors did not show any bad influence on the rheological property of drilling fluids. Even though the compressive strength decreased when the solid precursors blended with barite, the strength values can still achieve 8 MPa. The reaction of metakaolin and activator formed cross-link structure in the mud-cake matrix, which enhanced the connection of the loose bentonite particles, lead to the significant enhancement of shear bonding strength and hydraulic bonding strength. This mud-cake solidification method provides a new approach to improve the quality of zonal isolation.

scholarly journals Effect of Cycloaliphatic Amine on the Shale Inhibitive Properties of Water-Based Drilling Fluid

2015 ◽  
Vol 8 (1) ◽  
pp. 19-27 ◽  
Author(s):  
Hanyi Zhong ◽  
Dong Sun ◽  
Weian Huang ◽  
Yunfeng Liu ◽  
Zhengsong Qiu
Keyword(s):  
High Temperature ◽  
Drilling Fluid ◽  
Hardness Test ◽  
Drilling Fluids ◽  
The Novel ◽  
Potential Measurement ◽  
Clay Particles ◽  
Water Based ◽  
Bulk Hardness ◽  
Dispersion Test

In order to improve the inhibitive properties and high temperature resistance of shale inhibitor, cycloaliphatic amines were introduced as shale hydration inhibitors in water-based drilling fluids. Bulk hardness test, shale cuttings dispersion test, bentonite inhibition test and water adsorption test were carried out to characterize the inhibitive properties of the novel amines. Surface tension measurement, zeta potential measurement, XRD, contact angle test, SEM and TGA were performed to investigate the interaction between the cycloaliphatic amines and clay particles. The results indicated that cycloaliphatic amines exhibited superior inhibitive properties to the state of the art inhibitors. Moreover, the amines were high temperature resistant. The hydrophobic amine could intercalate into the clay gallery with monolayer orientation. The protonated ammonium ions neutralized the negatively charged surface. After adsorption, the hydrophobic segment covered the clay surface and provided a shell preventing the ingress of water.

Sign in / Sign up

Export Citation Format

Share Document