scholarly journals Eriobotrya japonica Lindl. Kernels: Kinetics of Thermal Degradation under Inert Atmosphere Using Model-Free and Fitting Methods

2020 ◽  
Vol 11 (4) ◽  
pp. 11357-11379

A kinetic study of the pyrolysis process of raw Eriobotrya japonica Lindl. Kernels (RLK) was investigated using a thermogravimetric analyzer. The weight loss was measured in a nitrogen atmosphere. The samples were heated over a range of temperature from 298 K to 873 K with four different heating rates of 5, 10, 15, 20 K min-1. Mass loss (TGA) and derivative mass loss (DTG) measurements indicate that the increase in heating rate has no noticeable effect on the thermal degradation of the RLK. The results obtained from the thermal decomposition process indicate that there are three main stages such as dehydration, active, and passive pyrolysis. TGA curves indicate that active pyrolysis of RLK is between 160 and 450 °C. In this interval, a shoulder followed by a peak exists on the DTG plots. The shoulder corresponds to the decomposition of hemicelluloses, the first peak to that of cellulose. Lignin decomposes through all temperature range. The kinetic parameters such as activation energy and pre-exponential factor were obtained for two degradation steps by isoconversional model-free methods proposed by FWO, KAS, Kissinger, Tang, MKN, and FR, with degradation mode being: f(α)=(1-α)n with n = 1 for FR and g(α)=-Ln(1- α) for the other methods. The activation energy and pre-exponential factor obtained by the Kissinger method are 173 kJ/mol and 1.9×1016 min-1. While for free model methods, the average kinetic parameters calculated are 172-248 kJ.mol-1 and 5,30×1020 for integral methods (FWO, KAS, Tang and MKN) and 190-271 kJ.mol-1 and 1.77×1022 min-1 for differential Fr method. The activation energy decreases in the final stages of the process. The energy required for hemicellulose degradation is lower than that of cellulose. The most probable reaction functions have thus been determined for these two stages by Coats-Redfern and Criado method, leading to greatly improved calculation performance over the entire conversion range. The reaction, second-order F2, describes the pyrolysis reaction models of RLK. With the Arrhenius parameters obtained from the fitting model of CR, we attempt to reconstruct the temperature-dependent mass conversion curves and have resulted in generally acceptable results. Based on the Arrhenius parameter values obtained by Kissinger equation, the changes in entropy, enthalpy and Gibbs free energy, and lifetime predictions have been estimated concerning the thermal degradation processes of RLK.

2020 ◽  
Vol 22 (3) ◽  
pp. 64-69
Author(s):  
Saira Bano ◽  
Naveed Ramzan ◽  
Tanveer Iqbal ◽  
Hamayoun Mahmood ◽  
Farhan Saeed

AbstractThis work investigated kinetics and thermal degradation of acrylonitrile butadiene styrene and polycarbonate (ABS/PC) blend using thermogravimetric analysis in the range of 25 to 520°C. For thermal degradation of blend, activation energy (Ea) and pre-exponential factor (A) were calculated under various heating rates as 5, 10, 15 and 20°C/min using iso-conversional model-free methods (Kissinger, Flynn-Wall- Ozawa and Friedman). Mass loss of the blend as a function of temperature was plotted as thermogravimetric curve (TG) while derivative values of mass loss were drawn as derivative thermogravimetric (DTG) curve. Using Kissinger method, Ea was 51.4 kJ/mol, while values calculated from FWO and Friedman method were 86–161 and 30–251 kJ/mol respectively. Results showed increasing trend of Ea with higher conversion values indicating different degradation mechanisms at the initial and final stages of the experiment. Thermodynamic parameters such as enthalpy change (ΔH), Gibbs free energy (ΔG) and entropy change (ΔS) were also calculated.


2019 ◽  
Vol 38 (2) ◽  
pp. 202-212 ◽  
Author(s):  
Ghulam Ali ◽  
Jan Nisar ◽  
Munawar Iqbal ◽  
Afzal Shah ◽  
Mazhar Abbas ◽  
...  

Due to a huge increase in polymer production, a tremendous increase in municipal solid waste is observed. Every year the existing landfills for disposal of waste polymers decrease and the effective recycling techniques for waste polymers are getting more and more important. In this work pyrolysis of waste polystyrene was performed in the presence of a laboratory synthesized copper oxide. The samples were pyrolyzed at different heating rates that is, 5°Cmin−1, 10°Cmin−1, 15°Cmin−1 and 20°Cmin−1 in a thermogravimetric analyzer in inert atmosphere using nitrogen. Thermogravimetric data were interpreted using various model fitting (Coats–Redfern) and model free methods (Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman). Thermodynamic parameters for the reaction were also determined. The activation energy calculated applying Coats–Redfern, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman models were found in the ranges 105–148.48 kJmol−1, 99.41–140.52 kJmol−1, 103.67–149.15 kJmol−1 and 99.93–141.25 kJmol−1, respectively. The lowest activation energy for polystyrene degradation in the presence of copper oxide indicates the suitability of catalyst for the decomposition reaction to take place at lower temperature. Moreover, the obtained kinetics and thermodynamic parameters would be very helpful in determining the reaction mechanism of the solid waste in a real system.


Polymers ◽  
2019 ◽  
Vol 11 (2) ◽  
pp. 281 ◽  
Author(s):  
Rafael Balart ◽  
David Garcia-Sanoguera ◽  
Luis Quiles-Carrillo ◽  
Nestor Montanes ◽  
Sergio Torres-Giner

This work presents an in-depth kinetic study of the thermal degradation of recycled acrylonitrile-butadiene-styrene (ABS) polymer. Non-isothermal thermogravimetric analysis (TGA) data in nitrogen atmosphere at different heating rates comprised between 2 and 30 K min−1 were used to obtain the apparent activation energy (Ea) of the thermal degradation process of ABS by isoconversional (differential and integral) model-free methods. Among others, the differential Friedman method was used. Regarding integral methods, several methods with different approximations of the temperature integral were used, which gave different accuracies in Ea. In particular, the Flynn-Wall-Ozawa (FWO), the Kissinger-Akahira-Sunose (KAS), and the Starink methods were used. The results obtained by these methods were compared to the Kissinger method based on peak temperature (Tm) measurements at the maximum degradation rate. Combined Kinetic Analysis (CKA) was also carried out by using a modified expression derived from the general Sestak-Berggren equation with excellent results compared with the previous methods. Isoconversional methods revealed negligible variation of Ea with the conversion. Furthermore, the reaction model was assessed by calculating the characteristic and functions and comparing them with some master plots, resulting in a nth order reaction model with n = 1.4950, which allowed calculating the pre-exponential factor (A) of the Arrhenius constant. The results showed that Ea of the thermal degradation of ABS was 163.3 kJ mol−1, while ln A was 27.5410 (A in min−1). The predicted values obtained by integration of the general kinetic expression with the calculated kinetic triplet were in full agreement with the experimental data, thus giving evidence of the accuracy of the obtained kinetic parameters.


2018 ◽  
Vol 39 (1) ◽  
pp. 58-67 ◽  
Author(s):  
Dev K. Mandal ◽  
Haripada Bhunia ◽  
Pramod K. Bajpai

AbstractIn this article, the influence of polylactide and pro-oxidant on the thermal stability, degradation kinetics, and lifetime of polypropylene has been investigated using thermogravimetric analysis under nitrogen atmosphere at four different heating rates (i.e. 5, 10, 15, and 20°C/min). The kinetic parameters of degradation were studied over a temperature range of 30–550°C. The derivative thermogravimetric curves have indicated single stage and two stage degradation processes. The activation energy was evaluated by using the Kissinger, Kim-Park, and Flynn-Wall methods under the nitrogen atmosphere. The activation energy value of polypropylene was much higher than that of polylactide. Addition of polylactide and pro-oxidant in polypropylene decreased the activation energy. The lifetime of polypropylene has also decreased with the addition of polylactide and pro-oxidant.


2018 ◽  
Vol 28 ◽  
pp. 75-89
Author(s):  
Hamid Reza Javadinejad ◽  
Sayed Ahmad Hosseini ◽  
Mohsen Saboktakin Rizi ◽  
Eiman Aghababaei ◽  
Hossein Naseri

The kinetic study for the synthesis of Fluorapatite has been done using the thermogravimetric technique under non-isothermal conditions and at four heating rates of 5, 10, 15 and 20 °C. Both model free and model-fitting methods were used to investigate kinetic parameters. Calcium oxide, phosphorus pentoxide and calcium fluoride were used as the precursor materials. The activation energy values were calculated through model-fitting and isoconversional methods and were used to predict the reaction model and pre-exponential factor. In this case several techniques were considered such as master plots and compensation effects. The results indicated that the reaction mechanism was chemically controlled with second and third order reaction models in the whole range of conversion which the activation energy varied from 25 to 43 kJ/mol.


2018 ◽  
Vol 21 (2) ◽  
pp. 75-80 ◽  
Author(s):  
Alok Dhaundiyal ◽  
Muammel M. Hanon

Abstract This paper deals with pyrolysis decomposition of Cedrus deodara leaves with the help of thermogravimetric analysis (TGA). Experiments are performed in the presence of inert atmosphere of nitrogen. Experiments are conducted at three different heating rates of 5 °C∙min-1, 10 °C∙min-1 and 15 °C∙min-1 within temperature range of 35 °C to 700 °C. Arrhenius parameters such as activation energy and frequency factor are estimated by Flynn Wall and Ozawa (FWO), Kissinger-Akahira-Sonuse (KAS) and Kissinger. The activation energy and frequency factor calculated by using Kissinger method are 67.63 kJ∙mol-1 and 15.06 . 104 min-1 respectively; whereas the averaged values of the same parameters through FWO and KAS methods are 89.59 kJ∙mol-1 and 84.748 kJ∙mol-1, 17.27 . 108 min-1 and 62.13 . 107 min-1 respectively. Results obtained through Kissinger method represent the actual values of kinetic parameters. Conversely, FWO and KAS methods reflect the apparent values of kinetic parameters, as they are highly influenced by the overlapping of competitive reactions occur during pyrolysis.


Energies ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 34
Author(s):  
Przemysław Grzywacz ◽  
Grzegorz Czerski ◽  
Wojciech Gańczarczyk

The aim of the study is to assess the influence of the atmosphere during pyrolysis on the course of CO2 gasification of a tire waste char. Two approaches were used: the pyrolysis step was carried out in an inert atmosphere of argon (I) or in an atmosphere of carbon dioxide (II). The examinations were carried out in non-isothermal conditions using a Rubotherm DynTherm thermobalance in the temperature range of 20–1100 °C and three heating rates: 5, 10 and 15 K/min. Based on the results of the gasification examinations, the TG (Thermogravimetry) and DTG (Derivative Thermogravimetry) curves were developed and the kinetic parameters were calculated using the KAS (Kissinger-Akahira-Sunose) and FWO (Flynn-Wall-Ozawa) methods. Additionally, the CO2 gasification of tire chars reaction order (n), was evaluated, and the kinetic parameters were calculated with the use of Coats and Redfern method. Tire waste char obtained in an argon atmosphere was characterized by lower reactivity, which was reflected in shift of conversion and DTG curves to higher temperatures and higher mean values of activation energy. A variability of activation energy values with the progress of the reaction was observed. For char obtained in an argon atmosphere, the activation energy varied in the range of 191.1–277.2 kJ/mol and, for a char obtained in an atmosphere of CO2, in the range of 148.0–284.8 kJ/mol. The highest activation energy values were observed at the beginning of the gasification process and the lowest for the conversion degree 0.5–0.7.


2016 ◽  
Vol 36 (9) ◽  
pp. 917-931 ◽  
Author(s):  
Gaurav Madhu ◽  
Dev K. Mandal ◽  
Haripada Bhunia ◽  
Pramod K. Bajpai

Abstract The effect of adding poly(L-lactic acid) (PLLA) with and without a pro-oxidant additive cobalt stearate (CoSt) and compatibilizer maleic anhydride grafted polyethylene (MA-g-PE) on the thermal degradation and stability of high-density polyethylene (HDPE) films was analyzed using thermogravimetric analysis (TGA). The kinetic parameters [i.e. activation energy (Ea), order of reaction (n), and frequency factor ln(A)] of the samples were studied over a temperature range of 25°C–600°C at four heating rates (i.e. 5, 10, 15, and 20°C/min) through model-free techniques (e.g. Friedman, second Kissinger, and Flynn-Wall-Ozawa) and model-fitting techniques (e.g. Freeman-Carroll and Kim-Park). The value of Ea for neat HDPE was found to be much higher than PLLA; for the HDPE/PLLA blend, it was nearer to that of HDPE. An increase in the activation energy of 80/20 (HDPE/PLLA) blend was noticed by the addition of MA-g-PE. The TGA data and degradation kinetics were also used to predict the lifetime of the film samples. The lifetime of HDPE was found to decrease with the increase in the concentration of CoSt, thereby revealing its pro-oxidative ability. Minimum lifetime was noted for the HDPE/PLLA (80/20) sample blended with CoSt, which increased slightly in the presence of MA-g-PE. Studies indicated that the thermal degradation behavior and lifetime of the investigated film samples depends not only on the fractions of their constituents but also on the heating rates and calculation technique.


Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 653
Author(s):  
Peng Ren ◽  
Qingmin Li ◽  
Honglei Liu ◽  
Yunpeng Li ◽  
Peng Peng ◽  
...  

To reliably detect the latent defects and accurately evaluate the remaining life of gas insulated switchgear (GIS) basin insulators, more effective detection and characterization methods need to be explored. The study of pyrolysis kinetic parameters based on the intrinsic characteristics of materials provides a new way to solve this problem. First, an integral expression model of the reaction mechanism function with four parameters is proposed in this paper, which can represent various existing reaction mechanism functions with better universality and more application fields. Then, on the basis of the temperature transformation equation, an improved method for calculating the activation energy is presented, which shows higher computational accuracy than the existing methods. Further, based on a non-isothermal kinetic equation, the structure of the experimental function is given. It is a method for solving the pyrolysis reaction mechanism function of insulating materials, which can also be used to calculate the pre-exponential factor simultaneously. The thermogravimetric analysis experiment is carried out on a certain basin insulator sample at different heating rates. The pyrolysis kinetic state parameters, including the activation energy, reaction mechanism function and pre-exponential factor of the basin insulator, are calculated. Finally, the life prediction method of basin insulators is established, and the key factors affecting the life of insulators are discussed.


Biomass residues have potential to be used as an alternative solid fuel for various processes, also will be responsible for the optimization of the pyrolysis reaction processes, giving insight into the pyrolysis mechanisms and aiding in engineering efforts. There are different methods for production of bio-fuel from biomass residues; however before the production of bio-fuels from biomass it is important to understand their thermal degradation and kinetics. In the present work the Kinetics studies of four different walnut shells, namely, paper (PSW), thin (TSW), medium (MSW) and hard (HSW) shelled walnuts have been studied. Thermal degradation behaviour of walnut shells is investigated using thermogravimetric analysis (TGA) under three different heating rates (30, 60 and 100 0Cmin−1 ) in an oxidizing atmosphere to understand the kinetic behavior. Kissinger–Akahira–Sunose (KAS) and Ozawa–Flynn–Wall (OFW) methods were used to estimate the kinetic parameters such as Pre-exponential factor (R) and average activation energy (Ea ) using TGA data of active zone. The average activation energy of biomass obtained from PSW, TSW, MSW and HSW using KAS method were 198.25, 184.21, 180.93, and 152.79 kJ mol−1 , respectively. Whereas by OFW method the values were found to be 204.10, 186.28, 188.39 and 153.78 kJ mol−1 respectively. Thus the present investigation may be useful for its use as a renewable energy source and potential candidate for fuel production by thermo-chemical processes.


Sign in / Sign up

Export Citation Format

Share Document