scholarly journals Modified Structural and Magnetic Properties of Ni-Mn-Zn Ferrite Nanoparticles Doped with Ce3+Ions

2021 ◽  
Vol 12 (4) ◽  
pp. 5021-5030
Keyword(s):  
Spinel Ferrite ◽  
Sol Gel ◽  
Lattice Parameter ◽  
Sem Analysis ◽  
Dielectric Measurements ◽  
X Ray Diffraction ◽  
High Frequency Region ◽  
X Ray ◽  
Zn Ferrite ◽  
Xrd Patterns

Polycrystalline Ni-Mn-Zn nano-ferrites doped by the fractional amount of Ce3+ ions were fabricated using the sol-gel method. Characterizations of the as-prepared samples were performed by using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDAX), vibrating sample magnetometer (VSM), and dielectric measurements. Rietveld refined XRD patterns revealed the single-phase cubic spinel structure of the samples corresponds to the space group Fd-3m. Minor shifting of peak positions towards lower diffraction angles increases lattice parameter from 8.4105 to 8.4193 Å with the addition of Ce3+ ions. , The surface morphology and homogeneity of the samples were investigated by using SEM and EDAX spectra. Grain size obtained from SEM analysis is found in the range 29 nm to 33 nm with negligible agglomeration. Analysis of EDAX spectra confirms the stoichiometric proportion of the constituents. Substitution of Ce3+ ions shows typical ferromagnetic curves with enhanced saturation magnetization and magneton number from 54 to 63 emu/gm and 2.71 to 3.09 B respectively. Dielectric measurements of the entire samples show the typical behavior of spinel ferrite. The results predict that the samples are best suitable for high-frequency region applications.

Proficient Ni-Zn-Cr Ferrites: Synthesis and Characterization

2012 ◽  
Vol 510-511 ◽  
pp. 343-347
Author(s):  
S. Nasir ◽  
M.A. Malik ◽  
G. Asghar ◽  
G.H. Tariq ◽  
M. Akram ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zn Ferrite ◽  
Phase Spinel ◽  
Scherrer Formula ◽  
Xrd Patterns ◽  
Cr Doping

Ni-Zn ferrite nanoparticles with Cr doping, having the general formula Ni0.5Zn0.5CrxFe2-xO4(x = 0.1, 0.3, 0.5) were prepared by simplified sol-gel method and sintered at 750±5°C. The structural and magnetic properties of the samples sintered at 750±5°C were studied. From X-ray diffraction (XRD) patterns, it was confirmed that the samples have single phase spinel structure. The crystallite size was calculated from the most intense peak (3 1 1) using the Debye Scherrer formula and was found to be in the range of 29-34 nm. The scanning electron microscope images showed that the particle size of the samples were in the range 60-120nm. Quantum design PPMS model 6700 was used to study magnetic properties of these samples. The effect of Cr doping on the magnetic properties was explained on the basis of cations distribution in the crystal structure.

scholarly journals Structural and Electrical Properties of Nano [Ni 0.6 Zn 0.4 Fe2 O4] Spinel Ferrite

2021 ◽  
pp. 115-118
Author(s):  
Ramesh N. Taikar ◽  
Sadanand R. Sarve ◽  
Disha T. Yele ◽  
Deepak R. Taikar ◽  
Kalpana R. Nagde
Keyword(s):  
Electrical Properties ◽  
Spinel Ferrite ◽  
Sol Gel ◽  
Average Particle Size ◽  
Combustion Method ◽  
Average Particle ◽  
X Ray Diffraction ◽  
X Ray ◽  
Zn Ferrite ◽  
Auto Combustion

Nano Ni-Zn ferrite with composition Ni 0.6 Zn 0.4 Fe2O4 is prepared by using sol-gel auto-combustion method with citric acid as a fuel. The structural properties of synthesized nano-ferrite is characterized by powder X-ray diffraction (XRD) technique while the electrical properties have been studied using two probe method. The X-ray diffraction study confirms that, there is a formation of single-phase cubic spinel with most intense peak at [311] having lattice constant of 8.3585 A0 and the average particle size is found to be 45.63 nm. In addition to this, the electrical resistivity of Ni-Zn Ferrite decreases with increase in temperature which exhibits semiconductor nature.

High Curie temperature perovskite BiInO3–PbTiO3 ceramics

2004 ◽  
Vol 19 (7) ◽  
pp. 2185-2193 ◽  
Author(s):  
Runrun Duan ◽  
Robert F. Speyer ◽  
Edward Alberta ◽  
Thomas R. Shrout
Keyword(s):  
Curie Temperature ◽  
Sol Gel ◽  
High Curie Temperature ◽  
Dielectric Measurements ◽  
X Ray Diffraction ◽  
Compound Formation ◽  
X Ray ◽  
Oxide Powders ◽  
Phase Pure ◽  
Pbtio3 Ceramics

The extent of BiInO3 substitution in the perovskite system xBiInO3–(1 - x)PbTiO3 and the corresponding raise in the Curie temperature were investigated using thermal analysis, dielectric measurements, x-ray diffraction, and electron microscopy. Maximum tetragonal perovskite distortion (c/a = 1.082) was obtained for x = 0.20, with a corresponding Curie temperature of 582 °C. Phase-pure tetragonal perovskite was obtained for x ⩽ 0.25. Compound formation after calcining mixed oxide powders resulted in agglomerated cube-shaped tetragonal perovskite particles, which could be fired to 94.7% of theoretical density (TD). Sol-gel fabrication resulted in nano-sized tetragonal or pseudo-cubic perovskite particles, which after two-step firing, resulted in a tetragonal perovskite microstructure at as high as (x = 0.20) 98.1% of TD.

scholarly journals Crystal Structures and Magnetic Properties of Polyethylene Glycol (PEG-4000) Encapsulated Co0.5Ni0.5Fe2O4 Magnetic Nanoparticles

2018 ◽  
Vol 8 (2) ◽  
pp. 75
Author(s):  
Edi Suharyadi ◽  
Lintang Griyanika ◽  
Joko Utomo ◽  
Ayu Kurnia Agustina ◽  
Takeshi Kato ◽  
...  
Keyword(s):  
Magnetic Nanoparticles ◽  
Crystallite Size ◽  
Spinel Ferrite ◽  
Lattice Parameter ◽  
X Ray ◽  
Maximum Magnetization ◽  
Peg 4000 ◽  
Significant Difference ◽  
Ray Density ◽  
Xrd Patterns

Nanocrystalline mixed spinel ferrite of Co0.5Ni0.5Fe2O4 magnetic nanoparticles (MNPs) has been successfully synthesized by coprecipitation method and encapsulated by PEG-4000 with various concentrations. X-Ray Diffraction (XRD) patterns showed that nanoparticles contained Co0.5Ni0.5Fe2O4 spinel ferrite with crystallite size of 14.9 nm. After PEG-4000 encapsulation particles size decreased became 7.7 nm. Interaction Co0.5Ni0.5Fe2O4 nanoparticles with long chain PEG-4000 caused the crystal growth trap. Lattice parameter and X-Ray density have no significant difference after encapsulated PEG-4000. The coercivity (𝐻𝑐) of Co0.5Ni0.5Fe2O4 was 214 Oe. The 𝐻𝑐 decreased after PEG-4000 encapsulation became 127 Oe, which is due to the decrease of crystallite size. The maximum magnetization (Mmax) of Co0.5Ni0.5Fe2O4 was 12.0 emu/g, and decreased after PEG-4000 encapsulation to 11.7 emu/g, because PEG-4000 is paramagnetic. After the concentration of PEG-4000 increased, then the amount of paramagnetic material increase which lead maximum magnetization decrease.

scholarly journals Effect of Re and Tm-site on morphology structure and optical band gap of ReTmO3 (Re: La, Ce, Nd, Gd, Dy, Y and Tm: Fe, Cr) prepared by sol-gel method

2018 ◽  
Vol 64 (4) ◽  
pp. 381
Author(s):  
Muhammad Tufiq Jamil ◽  
Javed Ahmad ◽  
Syed Hamad Bukhari ◽  
Murtaza Saleem
Keyword(s):  
Band Gap ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Sem Analysis ◽  
X Ray Diffraction ◽  
Orthorhombic Crystal ◽  
X Ray ◽  
Average Grain Size ◽  
Auto Combustion ◽  
Uv Visible

Rare earth nano sized pollycrystalline orthoferrites and orthocromites ReT mO3 (Re = La, Nd, Gd, Dy, Y and T m = Fe, Cr) have been synthesized by sol-gel auto combustion citrate method. The samples have been characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), and UV-visible spectroscopy. The samples are single phase as confirmed by XRD analysis and correspond to the orthorhombic crystal symmetry with space group pbnm. Debye Scherer formula and Williamson Hall analysis have been used to calculate the average grain size which is consistent with that of determined from SEM analysis and varied between 25-75 nm. The elemental compositions of all samples have been checked by EDX analysis. Different crystallographic parameters are calculated with strong structural correlation among Re and Tm sites. The optical energy band gap has been calculated by using Tauc relation estimated to be in the range of 1.77 - 1.87 eV and 2.77 - 3.14 eV, for ReFeO3 and ReCrO3, respectively.

Antibacterial Activity of Nickel -Doped ZnO\MWCNTs hybrid Prepared by Sol-Gel technique

2021 ◽  
Author(s):  
Selma M.H. AL-Jawad ◽  
Zahraa S. Shakir ◽  
Duha S. Ahmed
Keyword(s):  
Antibacterial Activity ◽  
Sol Gel ◽  
Inhibition Zone ◽  
Sem Analysis ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Zno Nps ◽  
X Ray ◽  
Vis Spectroscopy ◽  
Doped Zno

ZnO/MWCNTs hybrid and doped with different concentration of Nickel element prepared by using Sol-gel been technique reported. All samples were prepared and characterized by X-Ray Diffraction Analysis (XRD), Energy Dispersive X-ray Spectroscopy (EDS), Fourier-Transform Infrared Spectroscopy (FTIR), Field-Emission Scanning Electron Microscopy (FE-SEM), and UV-Vis spectroscopy have been identified the structural, optical and morphological properties. X-ray diffraction showed the polycrystalline nature with hexagonal wutzite structure of hybrid and doped with Nickel. The crystalline size of the hybrid nanostructure was increasing from 23.73 nm to 34.59 nm. Besides, the UV-Vis spectroscopy showed a significant decrease in the band gap values from 2.97 eV to 2.01 eV. Whereas the FE-SEM analysis confirm the formation spherical shapes of ZnO NPs deposited on cylindrical tubes representing the MWCNTs. The antibacterial activity reveals that the inhibition zone of Ni doped-ZnO/MWCNTs hybrid was 28.5 mm, 26.5 mm toward E. coli and S. aureus bacteria, respectively.

Synthesis and Characterization of Cadmium with Titanium Oxide (Cd-TiO2) Nanocomposite: Testing its Antibacterial Effect

2021 ◽  
Vol 12 (4) ◽  
pp. 2523-2529
Author(s):  
Daniel Sam N ◽  
Anish C I ◽  
Sabeena G ◽  
Rajaduraipandian S ◽  
Manobala ◽  
...  
Keyword(s):  
Sol Gel ◽  
Gram Negative Bacteria ◽  
X Ray Diffraction ◽  
Sem Images ◽  
Gram Negative ◽  
X Ray ◽  
Weight Percentage ◽  
Inhibition Concentration ◽  
Xrd Patterns

Sol gel methods were used for the study of the antimicrobial activity of Cd-TiO2 against gram-negative and positive bacteria. These Cd-TiO2 have been characterized by various optical and techniques. They have been exhibited by X-ray diffraction, scanning electron microscopy, ultraviolet spectroscopy, and infrared spectroscopy. The structures of the various XRD patterns indicate that the product has a structure. The particle size of Cd-TiO2 is 35nm. The SEM images confirm the spherical appearance of the sample. The energy X-ray spectra have been confirmed as well and then C, O, Ti, Cd, Pt element are present in Cd-TiO2. The weight percentage of Cadmium is 5.8%, Ti is 51.03%, C is 5.13% and O is 31.75% in Cd-TiO2. BET image shows that the major pore size distribution of Cd-TiO2 is ranged from 2.24 nm. The Cd-TiO2 that the antibacterial activity when tested against the pathogens only gram-negative bacteria such as Pseudomonas. The zone of minimum inhibition concentration was measured in a range of 20mm in 25μl and 30mm in 100μl.

Effects of Glass Elements on the Structural Evolution ofin situGrown Ferroelectric Perovskite Crystals in Sol-gel Derived Glass-ceramics

1997 ◽  
Vol 12 (4) ◽  
pp. 1131-1140 ◽  
Author(s):  
Kui Yao ◽  
Weiguang Zhu ◽  
Liangying Zhang ◽  
Xi Yao
Keyword(s):  
Crystallization Process ◽  
Sol Gel ◽  
Glass Ceramics ◽  
Structural Evolution ◽  
Dielectric Measurements ◽  
X Ray Diffraction ◽  
Process Change ◽  
X Ray ◽  
Ferroelectric Perovskite

Several ABO3perovskite ferroelectric crystals, PbTiO3, Pb(Zr, Ti)O3, and BaTiO3have beenin situgrown from amorphous gels with glass elements, and the structural evolution has been systematically investigated using x-ray diffraction (XRD), infrared spectra (IR), differential thermal analysis (DTA), thermogravimetric analysis (TGA), and dielectric measurements. It is found that in the Si-contained glass-ceramic systems, Si and B glass elements are incorporated into the crystalline structures, resulting in the variation of the crystallization process, change of lattice constant, and dielectric properties. Some metastable phases expressed by a general formula AxByGzOw(A = Pb and Ba; B = Zr and Ti; G for glass elements, especially for Si) have been observed and discussed.

Synthesis and Characterization of CeO2 Doped ZrO2 Ceramics by a Simple Sol-Gel Route

2017 ◽  
Vol 907 ◽  
pp. 56-60
Author(s):  
Ummuhanı Hilal Özer ◽  
Kerim Emre Öksüz ◽  
Ali Özer
Keyword(s):  
Tetragonal Phase ◽  
Sol Gel ◽  
Lattice Parameter ◽  
X Ray Diffraction ◽  
Ceramic Powders ◽  
Zirconia Ceramics ◽  
Simple Method ◽  
X Ray ◽  
Gel Technique

It is well known that sol-gel technique is a simple method to produce nano sized ceramic powders. In this study, cerium oxide doped zirconia samples, with 10 mol%-12mol% and14mol% CeO2, were synthesized by sol-gel technique and characterized. The surface morphology, elemental composition, microstructure, and phase analysis, of the sintered CeO2 doped ZrO2 ceramics were characterized by field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray (EDS) analysis, and X-ray diffraction (XRD) respectively. X-ray diffraction for samples sintered at 1550 °C for 4h revealed that the zirconia ceramics have a tetragonal phase structure. The addition of CeO2 can raise the content of the tetragonal phase, but the minor monoclinic phase exists even at the CeO2 content of 10 mol%. The effect of dopant concentration on the lattice parameter, average primary crystallite size and micro-strain was studied. Relative densities for CeO2 doped ZrO2 bulk ceramics varied between 95% and 99 %, depending on the CeO2 addition.

scholarly journals Enhancement of Photocatalytic Activity by Mg2+ Doped Ceria Quantum Dots

2017 ◽  
Vol 2 (1) ◽  
Keyword(s):  
Quantum Dots ◽  
Photocatalytic Activity ◽  
Quantum Dot ◽  
Sol Gel ◽  
Lattice Parameter ◽  
Doped Ceria ◽  
X Ray Diffraction ◽  
X Ray ◽  
Gel Technique ◽  
Cubic Structure

The pure and Mg2+ doped CeO2 quantum dot were synthesized by sol-gel technique. The prepared quantum dots were characterized using X-ray diffraction pattern (XRD), Scanning electron microscope (SEM-EDX). The XRD results show cubic structure of the CeO2 quantum dots. The crystalline size (D), microstrain (ε), dislocation density (δ) and lattice parameter (α) were calculated and analyzed. SEM-EDX analysis shows the morphology and the presence of elements. The photocatalytic activity of the synthesized quantum dot was evaluated based on the photodegradation of methylene blue (MB) by UV-Vis spectrometry.

Sign in / Sign up

Export Citation Format

Share Document