scholarly journals Feasibility study of exploiting gearbox oil temperature of wind turbine for improving a heat pump water heater in cold areas

2021 ◽  
pp. 54-62
Author(s):  
Refat Mohammed Abdullah Eshaq ◽  
Eryi Hu ◽  
Ameen A Alshaba ◽  
Aiman A.M Alsenwi
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Fuel Consumption ◽  
Heat Pump ◽  
Thermal Energy ◽  
Mechanical Energy ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Solar Collectors ◽  
Water Heater

Purpose. Feasibility of completely dispensing with solar collectors (SCs) that are used in heat pump (HP) systems for hot water in cold areas. Methodology. Since the temperature of gearbox oil is relatively high, lots of heat can be exploited. Therefore, the recovery of this unutilized heat from gearbox oil temperature of a wind turbine shows a promising solution in improving heat pump (HP) efficiency for hot water especially in cold environment or the district that is located in the north of our planet where the solar energy is very low. This investigation focuses on the feasibility of direct conversion of mechanical energy harvested from the wind speed into thermal energy by exploiting only the friction phenomenon inside the gearbox of the wind turbine by completely dispensing with solar collectors (SCs) that are used in combined solar assisted heat pump (SAHP) because the SCs have various problems, such as large heat loss, low efficiency, freezing and tube-burst, which may limit their applications. Findings. Results show that the wind turbine can provide the power required for HP during the winter season due to high wind speed in Xuzhou city, Jiangsu, China particularly in January. At best, coefficient of performance (COP) may reach 4.08 without SCs, thus the suggested system ensures high COP in addition to decrease in the fuel consumption by 23.25%. Originality. Wind power driven HPs have been suggested in many pervious papers as a sustainable measure to provide heat to a house; however, to improve COP of HP system, we suggest using a wind turbine to directly drive the HP and exploit gearbox oil temperature in an assistant heat exchanger installed after the HP evaporator for providing additional thermal energy to refrigerant R12 and cooling the gearbox oil. Practical value. The coefficient of performance (COP) of HP has reached 4.08 without SCs, so the suggested system demonstrates high COP in addition to the reduced fuel consumption. Approximately 23.25% of energy could be saved using this novel system compared to a fuel water heater for DHW.

scholarly journals Theoretical Analysis of a Single-Stage Gas-fired Ejector Heat Pump Water Heater

2021 ◽  
pp. 1-28
Author(s):  
Jeremy Spitzenberger ◽  
Pengtao Wang ◽  
Laith Ismael ◽  
Hongbin Ma ◽  
Ahmad Abuheiba ◽  
...  
Keyword(s):  
Heat Pump ◽  
Thermal Energy ◽  
Ambient Air ◽  
Single Stage ◽  
Coefficient Of Performance ◽  
Water Heater ◽  
Pump System ◽  
Heat Pump System ◽  
Heating Capacity ◽  
Condenser Temperature

Abstract Ejector driven systems have the ability to operate at high efficiencies, utilizing recycled thermal energy as a power source. For a typical ejector heat pump system, the increase of the condenser temperature reduces the coefficient of performance (COP). In addition, if the condenser temperature is higher than the critical temperature, the ejector may not function. In this situation, the condenser temperature must be reduced, and an additional heater will be utilized to heat the production water from the condenser temperature to the desired temperature. In this investigation, a single-stage gas-fired ejector heat pump (EHP) is investigated and thermodynamically modeled in order to optimize the system COP for the purpose of heating water by utilizing the thermal energy from the ambient air. The effects of the high-temperature evaporator (HTE) and low-temperature evaporator (LTE) temperatures on the ejector critical back pressure and the EHP system performance are examined for a HTE temperature range of 120-180 °C and LTE temperatures of 15.5, 17.5, and 19.5 °C. Results show that an optimized COP of the EHP system exists which depends on HTE and LTE temperatures, primary nozzle throat diameters. In addition, it is found that the EHP COP is independent of the ejector COP. From this investigation a maximum EHP COP of 1.31 is able to be achieved for a HTE temperature of 160 °C and a LTE temperature of 19.5 °C with a total heating capacity of 15.98 kW.

Performance of Add-On Heat Pump Water Heater (HPWH) Systems and Their Impacts on Electric Utility Loads

2010 ◽  
Author(s):  
Yahya I. Sharaf-Eldeen ◽  
Craig V. Muccio ◽  
Eric Gay
Keyword(s):  
Heat Pump ◽  
Energy Savings ◽  
Electric Energy ◽  
Electric Heating ◽  
Electric Utility ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Energy Output ◽  
Water Heater ◽  
Heat Pump Water Heater

This work involves measurements, analyses, and evaluations of the performance of add-on, Heat Pump Water Heater (HPWH) systems in residential and small commercial applications. Two air-source Heat Pump (HP) systems rated at 7,000- and 12,000-BTU (2.051- and 3.517-kWh), were utilized in this work. The two HPs were retrofitted to two 50-gallon (189.3 liters) electric-resistance storage water-heaters with their electric heating elements removed. A third, standard electric water-heater (EWH), was used for comparison. The testing set-up was fully instrumented for measurements of pertinent parameters, including inlet and outlet water temperatures, inlet and outlet air temperatures of the HPs, temperature and humidity of the air in the surrounding space, volume of water draws out of the storage heater tanks, as well as electric energy consumptions of the systems. Several performance measures were used in this work, including the Coefficient of Performance (COP), which is a measure of the instantaneous energy output in comparison with the energy input; Energy Factor (EF), which is an average measure of the COP taken over extended periods of time; and the First Hour Rating (FHR), which is a measure of the maximum volume of hot water that a storage type water-heater can supply to a residence within an hour. The results obtained clearly indicate that, HPWH systems are much more efficient as compared to standard EWHs. While the average value of the EF for a standard EWH is close to 1.0, the HPWH systems yield EFs averaging more than 2.00, resulting in annual energy savings averaging more than 50%. The results also showed that, HPWH systems are effective at reducing utility peak demand-loads, in addition to providing substantial cost savings to consumers.

scholarly journals Comparison of Transcritical CO2 and Conventional Refrigerant Heat Pump Water Heaters for Domestic Applications

Energies ◽  
2019 ◽  
Vol 12 (3) ◽  
pp. 479
Author(s):  
Ignacio Paniagua ◽  
Ángel Álvaro ◽  
Javier Martín ◽  
Celina Fernández ◽  
Rafael Carlier
Keyword(s):  
Heat Pump ◽  
Thermodynamic Cycle ◽  
Heat Pumps ◽  
Design Tool ◽  
Operating Conditions ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Ambient Conditions ◽  
Water Heater ◽  
Water Heaters

Although CO 2 as refrigerant is well known for having the lowest global warming potential (GWP), and commercial domestic heat pump water heater systems exist, its long expected wide spread use has not fully unfolded. Indeed, CO 2 poses some technological difficulties with respect to conventional refrigerants, but currently, these difficulties have been largely overcome. Numerous studies show that CO 2 heat pump water heaters can improve the coefficient of performance (COP) of conventional ones in the given conditions. In this study, the performances of transcritical CO 2 and R410A heat pump water heaters were compared for an integrated nearly zero-energy building (NZEB) application. The thermodynamic cycle of two commercial systems were modelled integrating experimental data, and these models were then used to analyse both heat pumps receiving and producing hot water at equal temperatures, operating at the same ambient temperature. Within the range of operation of the system, it is unclear which would achieve the better COP, as it depends critically on the conditions of operation, which in turn depend on the ambient conditions and especially on the actual use of the water. Technology changes on each side of the line of equal performance conditions of operation (EPOC), a useful design tool developed in the study. The transcritical CO 2 is more sensitive to operating conditions, and thus offers greater flexibility to the designer, as it allows improving performance by optimising the global system design.

scholarly journals Heat Pump Water Heater For Cold Climate – Canada

2021 ◽  
Author(s):  
Afarin Amirirad
Keyword(s):  
Energy Consumption ◽  
Heat Pump ◽  
Residential Buildings ◽  
Minimum Energy ◽  
Cold Climate ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Water Heater ◽  
Domestic Hot Water ◽  
Heat Pump Water Heater

Considering the large energy consumption of conventional water heaters in residential buildings, the performance of a new type of water heater has been characterized through conducting experiments and numerical modelling. The specific water heater investigated in this work benefits from heat absorption from the indoor air, denoted as the air source heat pump water heater (ASHPWH), and is located in the Archetype Sustainable Twin House B in Toronto. The experiments have been conducted under three different indoor conditions associated with temperature and humidity. The coefficient of performance (COP), which quantifies the ratio of heating capacity to the consumed power of ASHPWH, ranges between 1.5 and 5, depending on the indoor dry bulb and water inlet temperatures. A TRNSYS model of ASHPWH has been constructed based on the obtained experimental results and has subsequently been integrated with a TRNSYS model of the Archetype Sustainable House (ASH). The numerical results were verified with the experimental data. The model results suggests that after employing ASHPWH, the domestic hot water energy consumption reduces by 60.3% and 53.2% compared to the electric water heater in summer and winter respectively. Due to the energy absorption of ASHPWH from the indoor environment, the heating load of the ASH house increases while its cooling load decreases. Furthermore, the annual electricity consumption of the ASH house due to the required heating and cooling as well as the domestic hot water demand is reduced by 21.3%. Finally, as a consequence of employing ASHPWH, the energy cost and GHG emission were reduced respectively by 22% and 21.7%. By investigating the system in four other Canadian cities, it appears that Vancouver and Edmonton would have the maximum and minimum energy savings respectively.

scholarly journals Heat Pump Water Heater For Cold Climate – Canada

2021 ◽  
Author(s):  
Afarin Amirirad
Keyword(s):  
Energy Consumption ◽  
Heat Pump ◽  
Residential Buildings ◽  
Minimum Energy ◽  
Cold Climate ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Water Heater ◽  
Domestic Hot Water ◽  
Heat Pump Water Heater

Considering the large energy consumption of conventional water heaters in residential buildings, the performance of a new type of water heater has been characterized through conducting experiments and numerical modelling. The specific water heater investigated in this work benefits from heat absorption from the indoor air, denoted as the air source heat pump water heater (ASHPWH), and is located in the Archetype Sustainable Twin House B in Toronto. The experiments have been conducted under three different indoor conditions associated with temperature and humidity. The coefficient of performance (COP), which quantifies the ratio of heating capacity to the consumed power of ASHPWH, ranges between 1.5 and 5, depending on the indoor dry bulb and water inlet temperatures. A TRNSYS model of ASHPWH has been constructed based on the obtained experimental results and has subsequently been integrated with a TRNSYS model of the Archetype Sustainable House (ASH). The numerical results were verified with the experimental data. The model results suggests that after employing ASHPWH, the domestic hot water energy consumption reduces by 60.3% and 53.2% compared to the electric water heater in summer and winter respectively. Due to the energy absorption of ASHPWH from the indoor environment, the heating load of the ASH house increases while its cooling load decreases. Furthermore, the annual electricity consumption of the ASH house due to the required heating and cooling as well as the domestic hot water demand is reduced by 21.3%. Finally, as a consequence of employing ASHPWH, the energy cost and GHG emission were reduced respectively by 22% and 21.7%. By investigating the system in four other Canadian cities, it appears that Vancouver and Edmonton would have the maximum and minimum energy savings respectively.

Development and Performance Validation of a Heat Pump Water Heater

2006 ◽  
Author(s):  
H. I. Abu-Mulaweh
Keyword(s):  
Heat Pump ◽  
Testing Procedure ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Experimental Measurements ◽  
Water Heater ◽  
Flow Rates ◽  
Heat Pump Water Heater ◽  
And Performance ◽  
Performance Validation

Heat pump water heater was designed and a prototype was developed and constructed. The performance of the heat pump water heater prototype is described by presenting some experimental test data. The experimental measurements include temperature, flow rates, and power consumption. The testing procedure consisted of evaluating the recovery rate and the coefficient of performance (COP) of the system. The results strongly indicate that heat pump water heater system design is very practical and it provides the consumer with a more efficient hot water heater alternative.

Analysis of Domestic Hot Water Production Efficiency for Detached Houses

2015 ◽  
Vol 797 ◽  
pp. 185-191
Author(s):  
Arkadiusz Gużda ◽  
Norbert Szmolke
Keyword(s):  
Heat Pump ◽  
Production Efficiency ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Water Production ◽  
Water Heater ◽  
Domestic Hot Water ◽  
Air Source Heat Pump ◽  
Heat Pump Water Heater ◽  
Detached House

The article compares two means for domestic hot water production (DHW) for a detached house that is using gas boiler with a closed combustion chamber and air source heat pump water heater (ASHPWH). An analysis of domestic hot water production using an air source heat pump was made taking into account coefficient of performance listed according to the new BS EN 16147 standard. The analysis of outlay related to the investment and operating costs was also performed. Ultimately, the more profitable choice for domestic hot water production was made.

scholarly journals A New Solar Assisted Heat Pump System with Underground Energy Storage: Modelling and Optimisation

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5137
Author(s):  
Paweł Ocłoń ◽  
Maciej Ławryńczuk ◽  
Marek Czamara
Keyword(s):  
Energy Storage ◽  
Heat Pump ◽  
Thermal Energy ◽  
Waste Heat ◽  
Renewable Energy Sources ◽  
Energy Performance ◽  
Hot Water ◽  
Jaya Algorithm ◽  
Solar Collectors ◽  
Pump System

The objectives of this work are: (a) to present a new system for building heating which is based on underground energy storage, (b) to develop a mathematical model of the system, and (c) to optimise the energy performance of the system. The system includes Photovoltaic Thermal Hybrid Solar Panels (PVT) panels with cooling, an evacuated solar collector and a water-to-water heat pump. Additionally, storage tanks, placed underground, are used to store the waste heat from PVT panels cooling. The thermal energy produced by the solar collectors is used for both domestic hot water preparation and thermal energy storage. Both PVT panels and solar collectors are assembled with a sun-tracking system to achieve the highest possible solar energy gain. Optimisation of the proposed system is considered to achieve the highest Renewable Energy Sources (RES) share during the heating period. Because the resulting optimisation problem is nonlinear, the classical gradient-based optimisation algorithm gives solutions that are not satisfying. As alternatives, three heuristic global optimisation methods are considered: the Genetic Algorithm (GA), the Particle Swarm Optimisation (PSO) algorithm, and the Jaya algorithm. It is shown that the Jaya algorithm outperforms the GA and PSO methods. The most significant result is that 93% of thermal energy is covered by using the underground energy storage unit consisting of two tanks.

Performance optimization of an air source heat pump water heater using mathematical modelling

2015 ◽  
Vol 26 (1) ◽  
pp. 96-105 ◽  
Author(s):  
Stephen Tangwe ◽  
Michael Simon ◽  
Edson L. Meyer ◽  
Sampson Mwampheli ◽  
Golden Makaka
Keyword(s):  
Ambient Temperature ◽  
Heat Pump ◽  
Performance Optimization ◽  
Rate Of Change ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Water Tank ◽  
Water Heater ◽  
Conservation Of Energy ◽  
Air Source Heat Pump

In South Africa, there is an ongoing constraint on the electricity supply at the national grid to meet the demand. Eskom is implementing various measures such as the Integrated Demand Management and the promotion and encouragement of the use of energy efficient devices like an Air Source Heat pump (ASHP) water heater to replace the high electrical energy consuming conventional geysers for sanitary hot water production. The ASHP water heater market is fast gaining maturity. A critical mathematical model can lead to performance optimization of the systems that will further result in the conservation of energy and significant reduction in global warming potential. The ASHP water heater comprises of an ASHP unit and a hot water storage tank. In this study, a data acquisition system (DAS) was designed and built which monitored the energy used by the geyser and the whole building, the temperature at the evaporator, condenser, tank outlet hot water, tank inlet cold water, the ambient temperature and relative humidity in the vicinity of the ASHP evaporator. It is also worthy to mention that the DAS also included to a flow meter and two additional temperature sensors that measured the volume of water heated and inlet and outlet water temperature of the ASHP. This work focused on using the mathematical equation for the Coefficient of Performance (COP) of an ideal Carnot’s heat pump (CHP) water heater to develop basic computation in M-file of MATLAB software in order to model the system based on two reservoir temperatures: evaporator temperatures (Tevp) of 0°C to 40°C (approximated to ambient temperature, Ta) and condenser temperatures (TCon) set at 50°C, 55°C and 60°C (approximated to the hot water set temperature of 50°C, 55°C and 60°C) respectively. Finally, an analytical comparison of a CHP water heater to the practical ASHP water heater was conducted on a hot water set point temperature of 55°C. From the modelling results, it can be deduced that at 0°C Tevp, the COP was 5.96 and 2.63 for CHP and ASHP water heater respectively, at a hot water set temperature of 55°C. Above 20°C Tevp, the rate of change of COP increased exponentially for the ideal CHP system, but was constant at 0.01/°C for the practically modelled ASHP water heater.

ANALISA PERFORMA TURBIN ANGIN SUMBU HORISONTAL BERSUDU AIRFOIL MELALUI VARIASI JUMLAH SUDU

ROTOR ◽  
2018 ◽  
Vol 11 (2) ◽  
pp. 18
Author(s):  
Wabang A Jhon ◽  
Abanat D.J Jufra ◽  
Hattu Edwin
Keyword(s):  
Wind Speed ◽  
Kinetic Energy ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Mechanical Energy ◽  
Coefficient Of Performance ◽  
Research Activity ◽  
Average Wind Speed ◽  
Wind Speeds ◽  
Average Wind

Indonesia is an area that has the potential for sufficient wind resources to be utilized for kinetic energy into other energy such as mechanical energy and electrical energy through its generators (generators). The way to utilize wind kinetic energy into other energy is through a device called a wind turbine. Wind turbines have been around since ancient times, and are called airfoil angled wind turbines. This airfoil wind turbine is designed only for areas with average wind speeds above 6m / s. While in Indonesia not all regions have the same wind speed. In certain seasons, the average wind speed is below 6 m / s. This has become a major problem in regions that have average wind speeds below 6 m / s. Seeing this condition, there is a need for scientific research to obtain wind turbines that can be used in areas with average wind speeds below 5m / s. For this reason, the research I want to do is get a wind turbine that can be used as a power plant in areas that have wind speeds below 6m / s. This research was conducted on the basis of scientific theory in fluid mechanics regarding the sweeping area of wind turbines and the performance of variations in the number of blades in the wind. In addition, the research in several scientific journals was used as the basis of this research This research method is an experimental method, in the form of testing a wind turbine axis prototype horizontal and airfoil axis. The details of the research activity are the design and manufacture of laboratory scale horizontal airfoil axis turbines. Next, testing with a fan as a source of wind. The fan used has three variations of speed, all of which are used to determine the lowest average wind speed that can be applied. The results of the research are where wind turbines with the greatest torque and power and the Coefficient of Performance (CP) with the highest value will be used as a result to be applied to the community. Based on experimental data, it can be concluded that the greatest torque and power occur in turbines with 4 blades with details at speed 1, the largest torque and power are 0.201 Nm and 4.5 W; at speed 2, the biggest torque and power are 0.25 Nm and 7.21 W; at speed 3, the biggest torque and power are 0.28 Nm and 8.35 W Keywords: wind turbine, airfoil, nozzle, diffuser

Sign in / Sign up

Export Citation Format

Share Document