scholarly journals Control Rod Drop Hydrodynamic Analysis Based on Numerical Simulation

2020 ◽  
Vol 8 ◽  
Author(s):  
Jie Cheng ◽  
Zhenying Wang ◽  
Chuan Lu ◽  
Jibin Zhang ◽  
Shumao Bi ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Nuclear Power ◽  
Power Plants ◽  
Degrees Of Freedom ◽  
Nuclear Reactor ◽  
Three Dimensional ◽  
Guide Tube ◽  
Control Rod ◽  
Drop Time ◽  
Maximum Impact Force

The drop time of the control rod plays an important role in judging whether a nuclear reactor can be safely shut down in an emergency condition and has become one of the most important parameters for the safety analysis of nuclear power plants. Exact assessment of the drop time is greatly dependent on the forces acting on the control rod. In this research, a three-dimensional numerical simulation of the control rod in a low-temperature heating reactor was established based on 6DOF (6 degrees of freedom) model using dynamic meshing technology, and it was used to analyze the control rod dropping experiment. The behavior of dropping the control rod was obtained, including the velocity, the displacement, and the pressure distribution on the control rod guide tube. The comparison between the simulation and the experiment results indicated that the simulation was capable of simulating the dropping characteristic of the control rod. Some important parameters can be calculated, such as the time of control rod dropping process and the maximum impact force. Based on this, useful information could be provided for the design of control rod driveline structure.

Validation of Analysis Models on Relocation Behavior of Molten Core Materials in Sodium-Cooled Fast Reactors Based on the Melt Discharge Experiment

2020 ◽  
Author(s):  
Kai Igarashi ◽  
Ryoji Onuki ◽  
Takaaki Sakai ◽  
Shinya Kato ◽  
Ken-ichi Matsuba ◽  
...  
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Large Scale ◽  
Heat Removal ◽  
Early Discharge ◽  
Core Material ◽  
Bottom Plate ◽  
Guide Tube ◽  
Control Rod ◽  
Analysis Models

Abstract In order to improve the safety of nuclear power plants, it is necessary to make sure measures against their severe accidents. Especially, in the case of a sodium-cooled fast reactor (SFR), there is a possibility of significant energy release due to formation of a large-scale molten fuel pool accompanied by re-criticality in the event of a core disruptive accident (CDA). It is important to ensure in-vessel retention that keeps and confines damaged core material in the reactor vessel even if the CDA occurs. CDA scenario initiated by Unprotected Loss Of Flow (ULOF), which is a typical cause of core damage, is generally categorized into four phases according to the progression of core-disruptive status, which are the initiating, early-discharge, material-relocation and heat-removal phases for the latest design in Japan. During the material-relocation phase, the molten core material flows down mainly through the control rod guide tube and is discharged into the inlet coolant plenum below the bottom of the core. The discharged molten core material collides with the bottom plate of the inlet plenum. Clarification of the accumulation behavior of molten core material with such a collision on the bottom plate is important to reduce uncertainties in the safety assessment of CDA. In present study, in order to make clear behavior of core melt materials during the CDAs of SFRs, analysis was conducted using the SIMMER-III code for a melt discharge simulation experiment [1] in which low-melting-point alloy was discharged into a shallow water pool. This report shows the validation results for the melt behavior by comparing with the experimental data.

Dynamic Response of a Nuclear Power Plant Subjected to External Accident Event

2010 ◽  
Author(s):  
Rosa Lo Frano ◽  
Giuseppe Forasassi
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Failure Modes ◽  
Nuclear Reactor ◽  
Structural Integrity ◽  
Three Dimensional ◽  
Containment System ◽  
Dynamic Loadings ◽  
Water Reactors ◽  
Set Up

In recent times there is a renewed worldwide interest in the development and application of advanced nuclear power plants (NPPs). Decisions on the construction of several NPPs with evolutionary light water reactors have been made (e.g. EPR in Finland and France, AP1000 in China, etc.) and more are under consideration for licensing in several countries. Innovative NPPs are designed to be built with very broad siting conditions; therefore the safety aspects related to the external events might follow new scenarios and failure modes, different from those well known for the currently operated reactors. In this paper, the intent is evaluating the structural integrity of a nuclear containment system subjected to dynamic loadings due to a Design Base Earthquake and an aircraft impact (large size civilian jets or military aircrafts impact), which represent the two most relevant external accidents that should be considered and investigated as part of the basic design of a NPP in particular a III+ and IV Gens. In fact a suitable safety design of the NPP containment system (according to the international safety and design code guidelines, as NRC or IAEA ones), even if designed to meet other design goal, may represent a “built-in protection” to avoid or mitigate the effects of mentioned dynamic loadings. To the purpose a rather sophisticated numerical methodology, adopting finite element (FEM) approach, is employed for studying the overall dynamic behaviour of nuclear reactor and to determine the structural effects of the propagation of dynamic seismic as well as impulsive loads (containment structure response) up to the relevant nuclear components. Therefore representative three-dimensional FEM models of mentioned NPP containment and aircraft structures were set up, and used, in the performed analyses taking also into account the suitable materials behaviour and their related constitutive laws as well as the seismic excitation (determined according to the NRC rules). Moreover the performed analyses and the carried out response analyses of internal components, to both the ground motion and impact loads, were studied to check the considered NPP containment strength reserve in the case of the considered events. The obtained results seem to confirm the possibility to achieve an optimization of the NPP internal components.

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons With Experiments

2010 ◽  
Author(s):  
Dean Deng ◽  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Nuclear Power ◽  
Power Plants ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Dissimilar Metal ◽  
Water Reactors

Recent discoveries of stress corrosion cracking (SCC) at nickel-based metals in pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It has been recognized that welding residual stress is an important factor causing the issue of SCC in a weldment. In this study, both numerical simulation technology and experimental method were employed to investigate the characteristics of welding residual stress distribution in several typical welded joints, which are used in nuclear power plants. These joints include a thick plate butt-welded Alloy 600 joint, a dissimilar metal J-groove set-in joint and a dissimilar metal girth-butt joint. First of all, numerical simulation technology was used to predict welding residual stresses in these three joints, and the influence of heat source model on welding residual stress was examined. Meanwhile, the influence of other thermal processes such as cladding, buttering and heat treatment on the final residual stresses in the dissimilar metal girth-butt joint was also clarified. Secondly, we also measured the residual stresses in three corresponding mock-ups. Finally, the comparisons of the simulation results and the measured data have shed light on how to effectively simulate welding residual stress in these typical joints.

Nuclear Power Plant Fires and Explosions: Part IV — Water Hammer Explosion Mechanisms

2017 ◽  
Author(s):  
Robert A. Leishear
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Water Hammer ◽  
Compression Process ◽  
Flammable Gas ◽  
Piping Systems ◽  
Fukushima Daiichi ◽  
Accident Conditions

Water hammers, or fluid transients, compress flammable gasses to their autognition temperatures in piping systems to cause fires or explosions. While this statement may be true for many industrial systems, the focus of this research are reactor coolant water systems (RCW) in nuclear power plants, which generate flammable gasses during normal operations and during accident conditions, such as loss of coolant accidents (LOCA’s) or reactor meltdowns. When combustion occurs, the gas will either burn (deflagrate) or explode, depending on the system geometry and the quantity of the flammable gas and oxygen. If there is sufficient oxygen inside the pipe during the compression process, an explosion can ignite immediately. If there is insufficient oxygen to initiate combustion inside the pipe, the flammable gas can only ignite if released to air, an oxygen rich environment. This presentation considers the fundamentals of gas compression and causes of ignition in nuclear reactor systems. In addition to these ignition mechanisms, specific applications are briefly considered. Those applications include a hydrogen fire following the Three Mile Island meltdown, hydrogen explosions following Fukushima Daiichi explosions, and on-going fires and explosions in U.S nuclear power plants. Novel conclusions are presented here as follows. 1. A hydrogen fire was ignited by water hammer at Three Mile Island. 2. Hydrogen explosions were ignited by water hammer at Fukushima Daiichi. 3. Piping damages in U.S. commercial nuclear reactor systems have occurred since reactors were first built. These damages were not caused by water hammer alone, but were caused by water hammer compression of flammable hydrogen and resultant deflagration or detonation inside of the piping.

The analysis of emergency situations related to fires at nuclear power plants

2021 ◽  
Vol 30 (5) ◽  
pp. 66-75
Author(s):  
S. A. Titov ◽  
N. M. Barbin ◽  
A. M. Kobelev
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Emergency Situations ◽  
The Usa ◽  
Large Fires ◽  
Short Circuits ◽  
Nuclear Reactor Core

Introduction. The article provides a system and statistical analysis of emergency situations associated with fires at nuclear power plants (NPPs) in various countries of the world for the period from 1955 to 2019. The countries, where fires occurred at nuclear power plants, were identified (the USA, Great Britain, Switzerland, the USSR, Germany, Spain, Japan, Russia, India and France). Facilities, exposed to fires, are identified; causes of fires are indicated. The types of reactors where accidents and incidents, accompanied by large fires, have been determined.The analysis of major emergency situations at nuclear power plants accompanied by large fires. During the period from 1955 to 2019, 27 large fires were registered at nuclear power plants in 10 countries. The largest number of major fires was registered in 1984 (three fires), all of them occurred in the USSR. Most frequently, emergency situations occurred at transformers and cable channels — 40 %, nuclear reactor core — 15 %, reactor turbine — 11 %, reactor vessel — 7 %, steam pipeline systems, cooling towers — 7 %. The main causes of fires were technical malfunctions — 33 %, fires caused by the personnel — 30 %, fires due to short circuits — 18 %, due to natural disasters (natural conditions) — 15 % and unknown reasons — 4 %. A greater number of fires were registered at RBMK — 6, VVER — 5, BWR — 3, and PWR — 3 reactors.Conclusions. Having analyzed accidents, involving large fires at nuclear power plants during the period from 1955 to 2019, we come to the conclusion that the largest number of large fires was registered in the USSR. Nonetheless, to ensure safety at all stages of the life cycle of a nuclear power plant, it is necessary to apply such measures that would prevent the occurrence of severe fires and ensure the protection of personnel and the general public from the effects of a radiation accident.

scholarly journals Structural Modeling and Dynamic Analysis of a Nuclear Reactor Building

2020 ◽  
Author(s):  
Evrim Oyguc ◽  
Abdul Hayır ◽  
Resat Oyguc
Keyword(s):  
Nonlinear Dynamic ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Energy Sources ◽  
Finite Element Program ◽  
Design Spectrum ◽  
Reactor Building ◽  
Set Up

Increasing energy demand urge the developing countries to consider different types of energy sources. Owing the fact that the energy production capacity of renewable energy sources is lower than a nuclear power plant, developed countries like US, France, Japan, Russia and China lead to construct nuclear power plants. These countries compensate 80% of their energy need from nuclear power plants. Further, they periodically conduct tests in order to assess the safety of the existing nuclear power plants by applying impact type loads to the structures. In this study, a sample third-generation nuclear reactor building has been selected to assess its seismic behavior and to observe the crack propagations of the prestressed outer containment. First, a 3D model has been set up using ABAQUS finite element program. Afterwards, modal analysis is conducted to determine the mode shapes. Nonlinear dynamic time history analyses are then followed using an artificial strong ground motion which is compatible with the mean design spectrum of the previously selected ground motions that are scaled to Eurocode 8 Soil type B design spectrum. Results of the conducted nonlinear dynamic analyses are considered in terms of stress distributions and crack propagations.

scholarly journals Assessment of water hammer effects on boiling water nuclear reactor core dynamics

2007 ◽  
Vol 22 (1) ◽  
pp. 18-33 ◽  
Author(s):  
Anis Bousbia-Salah
Keyword(s):  
Pressure Wave ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Water Hammer ◽  
Pressure Wave Amplitude ◽  
Sensitivity Studies ◽  
Rapid Transients ◽  
Complex Phenomena

Complex phenomena, as water hammer transients, occurring in nuclear power plants are still not very well investigated by the current best estimate computational tools. Within this frame work, a rapid positive reactivity addition into the core generated by a water hammer transient is considered. The numerical simulation of such phenomena was carried out using the coupled RELAP5/PARCS code. An over all data comparison shows good agreement between the calculated and measured core pressure wave trends. However, the predicted power response during the excursion phase did not correctly match the experimental tendency. Because of this, sensitivity studies have been carried out in order to identify the most influential parameters that govern the dynamics of the power excursion. After investigating the pressure wave amplitude and the void feed back responses, it was found that the disagreement between the calculated and measured data occurs mainly due to the RELAP5 low void condensation rate which seems to be questionable during rapid transients. .

scholarly journals PRELIMINARY DESIGN OF RDE FEEDWATER PUMP IMPELLER

2018 ◽  
Vol 20 (1) ◽  
pp. 1 ◽  
Author(s):  
Sri Sudadiyo
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Thermal Power ◽  
Performance Characteristics ◽  
Preliminary Design ◽  
Triangle Diagram ◽  
Pump Impeller ◽  
Impeller Blade ◽  
Feedwater Pump

Nowadays, pumps are being widely used in the thermal power generation including nuclear power plants. Reaktor Daya Eksperimental (RDE) is a proposed nuclear reactor concept for the type of nuclear power plant in Indonesia. This RDE has thermal power 10 MWth, and uses a feedwater pump within its steam cycle. The performance of feedwater pump depends on size and geometry of impeller model, such as the number of blades and the blade angle. The purpose of this study is to perform a preliminary design on an impeller of feedwater pump for RDE and to simulate its performance characteristics. The Fortran code is used as an aid in data calculation in order to rapidly compute the blade shape of feedwater pump impeller, particularly for a RDE case. The calculations analyses is solved by utilizing empirical correlations, which are related to size and geometry of a pump impeller model, while performance characteristics analysis is done based on velocity triangle diagram. The effect of leakage, pass through the impeller due to the required clearances between the feedwater pump impeller and the volute channel, is also considered. Comparison between the feedwater pump of HTR-10 and of RDE shows similarity in the trend line of curve shape. These characteristics curves will be very useful for the values prediction of performance of a RDE feedwater pump. Preliminary design of feedwater pump provides the size and geometry of impeller blade model with 5-blades, inlet angle 14.5 degrees, exit angle 25 degrees, inside diameter 81.3 mm, exit diameter 275.2 mm, thickness 4.7 mm, and height 14.1 mm. In addition, the optimal values of performance characteristics were obtained when flow capacity was 4.8 kg/s, fluid head was 29.1 m, shaft mechanical power was 2.64 kW, and efficiency was 52 % at rotational speed 1750 rpm.Keywords: Blade, impeller, pump, RDEDESAIN AWAL IMPELER POMPA AIR UMPAN RDE. Saat ini, pompa digunakan secara luas dalam pembangkit tenaga termal termasuk pembangkit listrik tenaga nuklir. Reaktor Daya Eksperimental (RDE) merupakan konsep reaktor nuklir yang diusulkan untuk tipe PLTN di Indonesia. RDE ini memiliki daya termal 10 MWth, dan menggunakan pompa air umpan dalam siklus uapnya. Kinerja pompa air umpan bergantung pada ukuran dan geometri model impeller, seperti jumlah sudu dan sudut sudu. Tujuan dari penelitian ini adalah untuk membuat rancangan awal impeller pompa air umpan untuk RDE dan untuk mensimulasikan karakteristik kinerjanya. Kode Fortran digunakan sebagai bantuan dalam penghitungan data untuk untuk mengkalkulasi secara cepat bentuk sudu impeller pompa air umpan, terutama pada kasus RDE. Analisis perhitungan dipecahkan menggunakan korelasi empiris yang terkait dengan ukuran dan geometri model impeller pompa, sedangkan analisis karakteristik kinerja dilakukan berdasarkan diagram segitiga kecepatan. Pengaruh bocoran, melalui impeler akibat celah yang diperlukan antara impeller pompa air umpan dan saluran volute, juga dipertimbangkan. Perbandingan antara pompa air umpan HTR-10 dan RDE menunjukkan kemiripan dalam garis tren bentuk kurva. Kurva karakteristik ini akan sangat berguna untuk perkiraan nilai kinerja pompa air umpan RDE. Desain awal pompa air umpan memberikan ukuran dan geometri model sudu impeller dengan 5-sudu, sudut masuk 14,5 derajat, sudut keluar 25 derajat, diameter dalam 81,3 mm, diameter luar 275,2 mm, ketebalan 4,7 mm, dan tinggi 14,1 mm. Selain itu, nilai optimal karakteristik kinerja diperoleh ketika kapasitas aliran 4,8 kg/s, head fluida 29,1 m, tenaga mekanik poros 2,64 kW, dan efisiensi 52 % pada kecepatan putaran 1750 rpm.Kata kunci: Sudu, impeler, pompa, RDE

Sign in / Sign up

Export Citation Format

Share Document