scholarly journals PRELIMINARY DESIGN OF RDE FEEDWATER PUMP IMPELLER

2018 ◽  
Vol 20 (1) ◽  
pp. 1 ◽  
Author(s):  
Sri Sudadiyo
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Thermal Power ◽  
Performance Characteristics ◽  
Preliminary Design ◽  
Triangle Diagram ◽  
Pump Impeller ◽  
Impeller Blade ◽  
Feedwater Pump

Nowadays, pumps are being widely used in the thermal power generation including nuclear power plants. Reaktor Daya Eksperimental (RDE) is a proposed nuclear reactor concept for the type of nuclear power plant in Indonesia. This RDE has thermal power 10 MWth, and uses a feedwater pump within its steam cycle. The performance of feedwater pump depends on size and geometry of impeller model, such as the number of blades and the blade angle. The purpose of this study is to perform a preliminary design on an impeller of feedwater pump for RDE and to simulate its performance characteristics. The Fortran code is used as an aid in data calculation in order to rapidly compute the blade shape of feedwater pump impeller, particularly for a RDE case. The calculations analyses is solved by utilizing empirical correlations, which are related to size and geometry of a pump impeller model, while performance characteristics analysis is done based on velocity triangle diagram. The effect of leakage, pass through the impeller due to the required clearances between the feedwater pump impeller and the volute channel, is also considered. Comparison between the feedwater pump of HTR-10 and of RDE shows similarity in the trend line of curve shape. These characteristics curves will be very useful for the values prediction of performance of a RDE feedwater pump. Preliminary design of feedwater pump provides the size and geometry of impeller blade model with 5-blades, inlet angle 14.5 degrees, exit angle 25 degrees, inside diameter 81.3 mm, exit diameter 275.2 mm, thickness 4.7 mm, and height 14.1 mm. In addition, the optimal values of performance characteristics were obtained when flow capacity was 4.8 kg/s, fluid head was 29.1 m, shaft mechanical power was 2.64 kW, and efficiency was 52 % at rotational speed 1750 rpm.Keywords: Blade, impeller, pump, RDEDESAIN AWAL IMPELER POMPA AIR UMPAN RDE. Saat ini, pompa digunakan secara luas dalam pembangkit tenaga termal termasuk pembangkit listrik tenaga nuklir. Reaktor Daya Eksperimental (RDE) merupakan konsep reaktor nuklir yang diusulkan untuk tipe PLTN di Indonesia. RDE ini memiliki daya termal 10 MWth, dan menggunakan pompa air umpan dalam siklus uapnya. Kinerja pompa air umpan bergantung pada ukuran dan geometri model impeller, seperti jumlah sudu dan sudut sudu. Tujuan dari penelitian ini adalah untuk membuat rancangan awal impeller pompa air umpan untuk RDE dan untuk mensimulasikan karakteristik kinerjanya. Kode Fortran digunakan sebagai bantuan dalam penghitungan data untuk untuk mengkalkulasi secara cepat bentuk sudu impeller pompa air umpan, terutama pada kasus RDE. Analisis perhitungan dipecahkan menggunakan korelasi empiris yang terkait dengan ukuran dan geometri model impeller pompa, sedangkan analisis karakteristik kinerja dilakukan berdasarkan diagram segitiga kecepatan. Pengaruh bocoran, melalui impeler akibat celah yang diperlukan antara impeller pompa air umpan dan saluran volute, juga dipertimbangkan. Perbandingan antara pompa air umpan HTR-10 dan RDE menunjukkan kemiripan dalam garis tren bentuk kurva. Kurva karakteristik ini akan sangat berguna untuk perkiraan nilai kinerja pompa air umpan RDE. Desain awal pompa air umpan memberikan ukuran dan geometri model sudu impeller dengan 5-sudu, sudut masuk 14,5 derajat, sudut keluar 25 derajat, diameter dalam 81,3 mm, diameter luar 275,2 mm, ketebalan 4,7 mm, dan tinggi 14,1 mm. Selain itu, nilai optimal karakteristik kinerja diperoleh ketika kapasitas aliran 4,8 kg/s, head fluida 29,1 m, tenaga mekanik poros 2,64 kW, dan efisiensi 52 % pada kecepatan putaran 1750 rpm.Kata kunci: Sudu, impeler, pompa, RDE

Reliability and redundancy allocation analysis applied to a nuclear protection system

2021 ◽  
Vol 9 (2B) ◽  
Author(s):  
Alexander Lucas Busse ◽  
João Manoel Losada Moreira
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Nuclear Reactors ◽  
Block Diagram ◽  
Thermal Power ◽  
Life Time ◽  
Spare Parts ◽  
Protection System ◽  
Under Construction

Brazil is constructing with national technology two small nuclear reactors for propulsion and for radioisotope production with thermal power levels between 20 and 50 MW. These nuclear reactors fit more in the class of small modular reactors (SMR) than in the class of large nuclear power plants. In this article we apply the design approach of SMRs to propose an architecture of reactor protection systems for the small reactor under construction in the country. To do that the probabilistic analysis of the architecture of a nuclear reactor protection system is evaluated to determine the sensitivity of the components through an Reliability Block Diagram modeling. It was evaluated the modification of the architecture and the addition of redundancies when using components with lower life time than the components usually used for this purpose. The results showed that after one year of operation, the reference RPS system presents a failure probability of 0.17 %. The modified system, with components with lower life time, presents a point reliability value only 0.070 % lower than the reference one, but this difference grows exponentially over time, and in 10 years of operation it can reach values above 95%. Using equipment with lower life time characteristics implies a greater number of redundancies and, additionally, a greater number of maintenance procedures and spare parts. Therefore, this technical feasibility analysis should consider a RAM simulation as well.

Thermodynamic Considerations for a Single-Reheat Cycle SCWR

2009 ◽  
Author(s):  
M. C. Naidin ◽  
R. Monichan ◽  
U. Zirn ◽  
K. Gabriel ◽  
I. Pioro
Keyword(s):  
Thermal Efficiency ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Thermal Power ◽  
Electrical Energy ◽  
Performance Simulation ◽  
Development Costs ◽  
And Performance ◽  
Steam Cycle

Currently, there are a number of Generation IV SuperCritical Water-cooled nuclear Reactor (SCWR) concepts under development worldwide. The main objectives for developing and utilizing SCWRs are: 1) Increase gross thermal efficiency of current Nuclear Power Plants (NPPs) from 30 – 35% to approximately 45 – 50%, and 2) Decrease capital and operational costs and, in doing so, decrease electrical-energy costs. SCW NPPs will have much higher operating parameters compared to current NPPs (i.e., steam pressures of about 25 MPa and steam outlet temperatures up to 625°C). Additionally, SCWRs will have a simplified flow circuit in which steam generators, steam dryers, steam separators, etc. will be eliminated. Furthermore, SCWRs operating at higher temperatures can facilitate an economical co-generation of hydrogen through thermo-chemical cycles (particularly, the copper-chlorine cycle) or direct high-temperature electrolysis. To decrease significantly the development costs of a SCW NPP, to increase its reliability, and to achieve similar high thermal efficiencies as the advanced fossil steam cycles it should be determined whether SCW NPPs can be designed with a steam-cycle arrangement that closely matches that of mature SuperCritical (SC) fossil-fired thermal power plants (including their SC-turbine technology). The state-of-the-art SC-steam cycles at fossil-fired power plants are designed with a single-steam reheat and regenerative feedwater heating. Due to that, they reach thermal steam-cycle efficiencies up to 54% (i.e., net plant efficiencies of up to 43% on a Higher Heating Value (HHV) Basis). This paper analyzes main parameters and performance in terms of thermal efficiency of a SCW NPP concept based on a direct regenerative steam cycle. To increase the thermal efficiency and to match current SC-turbine parameters, the cycle also includes a single steam-reheat stage. The cycle is comprised of: an SCWR, a SC turbine, which consists of one High-Pressure (HP) cylinder, one Intermediate-Pressure (IP) cylinder and two Low-Pressure (LP) cylinders, one deaerator, ten feedwater heaters, and pumps. Since this option includes a “nuclear” steam-reheat stage, the SCWR is based on a pressure-tube design. A thermal-performance simulation reveals that the overall thermal efficiency is approximately 50%.

Investigation of Thermal Efficiency of Generic Pressure-Channel Reactors With Steam Reheat

2016 ◽  
Author(s):  
Yifeng Zhou ◽  
Paul Ponomaryov ◽  
Cristina Mazza ◽  
Igor Pioro
Keyword(s):  
Thermal Efficiency ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Thermal Power ◽  
Difficult Problem ◽  
Combined Cycle ◽  
The Usa ◽  
Pressure Channel ◽  
High Neutron

Currently, i.e., in 2016, 4361 nuclear-power reactors operate in the world. 96.6% of these reactors are water-cooled (373 reactors (280 PWRs, 78 BWRs and 15 LGRs are cooled with light water and 48 reactors — PHWRs are cooled with heavy water. 15% of all water-cooled reactors are pressure-channel or pressure-tube design, the rest — pressure-vessel design. All current NPPs with water-cooled reactors have relatively low thermal efficiencies within 30–36% compared to that of current NPPs with AGRs (42%) and SFR (40%) and compared to that of modern advanced thermal power plants: combined-cycle plants (up to 62%) and supercritical-pressure coal-fired plants (up to 55%). Therefore, it is very important to propose ways of improvement of thermal efficiency for this largest group of nuclear-power reactors. It should be noted that among six Generation-IV nuclear-reactor concepts one concept is a SCWR, which might reach thermal efficiencies within the range of 45–50% and even beyond. However, this concept has been never tested, and the most difficult problem on the way of implementation of this type of reactor is the reliability of materials at supercritical pressures and temperatures, very aggressive reactor coolant – supercritical water, and high neutron flux. Up till now, no experiments on behavior of various core materials at these conditions have been reported so far in the open literature. As an interim way of thermal-efficiency improvement for water-cooled NPPs nuclear steam reheat can be considered. However, this way is more appropriate only for pressure-channel reactors, for example, CANDU-type or PHWRs. Moreover, in the 60’s and 70’s, Russia, the USA and some other countries have developed and implemented the nuclear steam reheat in subcritical-pressure experimental boiling reactors. Therefore, an objective of the current paper is to summarize this experience and to estimate effect of a number of parameters on thermal efficiencies of a generic pressure-channel reactors with nuclear steam reheat. For this purpose the DE-TOP program has been used.

General Layouts of Supercritical-Water NPPs

2010 ◽  
Author(s):  
I. Pioro ◽  
M. Naidin ◽  
S. Mokry ◽  
Eu. Saltanov ◽  
W. Peiman ◽  
...  
Keyword(s):  
Supercritical Water ◽  
Thermal Efficiency ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Thermal Power ◽  
Electrical Energy ◽  
Development Costs ◽  
Flow Circuit ◽  
Steam Cycle

Currently, there are a number of Generation IV SuperCritical Water-cooled nuclear Reactor (SCWR) concepts under development worldwide. The main objectives for developing and utilizing SCWRs are: 1) Increase gross thermal efficiency of current Nuclear Power Plants (NPPs) from 30–35% to approximately 45–50%, and 2) Decrease capital and operational costs and, in doing so, decrease electrical-energy costs. SuperCritical Water (SCW) NPPs will have much higher operating parameters compared to current NPPs (i.e., steam pressures of about 25 MPa and steam outlet temperatures up to 625°C). Additionally, SCWRs will have a simplified flow circuit in which steam generators, steam dryers, steam separators, etc. will be eliminated. Furthermore, SCWRs operating at higher temperatures can facilitate an economical co-generation of hydrogen through thermo-chemical cycles (particularly, the copper-chlorine cycle) or direct high-temperature electrolysis. To decrease significantly the development costs of an SCW NPP, to increase its reliability, and to achieve similar high thermal efficiencies as the advanced fossil-fired steam cycles, it should be determined whether SCW NPPs can be designed with a steam-cycle arrangement that closely matches that of mature SuperCritical (SC) fossil-fired thermal power plants (including their SC-turbine technology). The state-of-the-art SC-steam cycles at fossil-fired power plants are designed with a single-steam reheat and regenerative feedwater heating. Due to this, they reach thermal steam-cycle efficiencies up to 54% (i.e., net plant efficiencies of up to 43–50% on a Higher Heating Value (HHV) basis). This paper presents several possible general layouts of SCW NPPs, which are based on a regenerative-steam cycle. To increase the thermal efficiency and to match current SC-turbine parameters, the cycle also includes a single steam-reheat stage. Since these options include a nuclear steam-reheat stage, the SCWR is based on a pressure-tube design.

Power Cycles of Generation III and III+ Nuclear Power Plants

2014 ◽  
Author(s):  
Alexey Dragunov ◽  
Eugene Saltanov ◽  
Igor Pioro ◽  
Pavel Kirillov ◽  
Romney Duffey
Keyword(s):  
Renewable Energy ◽  
Natural Gas ◽  
Thermal Efficiency ◽  
Nuclear Power ◽  
Power Plants ◽  
Renewable Energy Sources ◽  
Thermal Power ◽  
Electrical Energy ◽  
Energy Sources ◽  
Thermal Power Plants

It is well known that the electrical-power generation is the key factor for advances in any other industries, agriculture and level of living. In general, electrical energy can be generated by: 1) non-renewable-energy sources such as coal, natural gas, oil, and nuclear; and 2) renewable-energy sources such as hydro, wind, solar, biomass, geothermal and marine. However, the main sources for electrical-energy generation are: 1) thermal - primary coal and secondary natural gas; 2) “large” hydro and 3) nuclear. The rest of the energy sources might have visible impact just in some countries. Modern advanced thermal power plants have reached very high thermal efficiencies (55–62%). In spite of that they are still the largest emitters of carbon dioxide into atmosphere. Due to that, reliable non-fossil-fuel energy generation, such as nuclear power, becomes more and more attractive. However, current Nuclear Power Plants (NPPs) are way behind by thermal efficiency (30–42%) compared to that of advanced thermal power plants. Therefore, it is important to consider various ways to enhance thermal efficiency of NPPs. The paper presents comparison of thermodynamic cycles and layouts of modern NPPs and discusses ways to improve their thermal efficiencies.

Nuclear Power Plant Fires and Explosions: Part IV — Water Hammer Explosion Mechanisms

2017 ◽  
Author(s):  
Robert A. Leishear
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Water Hammer ◽  
Compression Process ◽  
Flammable Gas ◽  
Piping Systems ◽  
Fukushima Daiichi ◽  
Accident Conditions

Water hammers, or fluid transients, compress flammable gasses to their autognition temperatures in piping systems to cause fires or explosions. While this statement may be true for many industrial systems, the focus of this research are reactor coolant water systems (RCW) in nuclear power plants, which generate flammable gasses during normal operations and during accident conditions, such as loss of coolant accidents (LOCA’s) or reactor meltdowns. When combustion occurs, the gas will either burn (deflagrate) or explode, depending on the system geometry and the quantity of the flammable gas and oxygen. If there is sufficient oxygen inside the pipe during the compression process, an explosion can ignite immediately. If there is insufficient oxygen to initiate combustion inside the pipe, the flammable gas can only ignite if released to air, an oxygen rich environment. This presentation considers the fundamentals of gas compression and causes of ignition in nuclear reactor systems. In addition to these ignition mechanisms, specific applications are briefly considered. Those applications include a hydrogen fire following the Three Mile Island meltdown, hydrogen explosions following Fukushima Daiichi explosions, and on-going fires and explosions in U.S nuclear power plants. Novel conclusions are presented here as follows. 1. A hydrogen fire was ignited by water hammer at Three Mile Island. 2. Hydrogen explosions were ignited by water hammer at Fukushima Daiichi. 3. Piping damages in U.S. commercial nuclear reactor systems have occurred since reactors were first built. These damages were not caused by water hammer alone, but were caused by water hammer compression of flammable hydrogen and resultant deflagration or detonation inside of the piping.

The analysis of emergency situations related to fires at nuclear power plants

2021 ◽  
Vol 30 (5) ◽  
pp. 66-75
Author(s):  
S. A. Titov ◽  
N. M. Barbin ◽  
A. M. Kobelev
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Emergency Situations ◽  
The Usa ◽  
Large Fires ◽  
Short Circuits ◽  
Nuclear Reactor Core

Introduction. The article provides a system and statistical analysis of emergency situations associated with fires at nuclear power plants (NPPs) in various countries of the world for the period from 1955 to 2019. The countries, where fires occurred at nuclear power plants, were identified (the USA, Great Britain, Switzerland, the USSR, Germany, Spain, Japan, Russia, India and France). Facilities, exposed to fires, are identified; causes of fires are indicated. The types of reactors where accidents and incidents, accompanied by large fires, have been determined.The analysis of major emergency situations at nuclear power plants accompanied by large fires. During the period from 1955 to 2019, 27 large fires were registered at nuclear power plants in 10 countries. The largest number of major fires was registered in 1984 (three fires), all of them occurred in the USSR. Most frequently, emergency situations occurred at transformers and cable channels — 40 %, nuclear reactor core — 15 %, reactor turbine — 11 %, reactor vessel — 7 %, steam pipeline systems, cooling towers — 7 %. The main causes of fires were technical malfunctions — 33 %, fires caused by the personnel — 30 %, fires due to short circuits — 18 %, due to natural disasters (natural conditions) — 15 % and unknown reasons — 4 %. A greater number of fires were registered at RBMK — 6, VVER — 5, BWR — 3, and PWR — 3 reactors.Conclusions. Having analyzed accidents, involving large fires at nuclear power plants during the period from 1955 to 2019, we come to the conclusion that the largest number of large fires was registered in the USSR. Nonetheless, to ensure safety at all stages of the life cycle of a nuclear power plant, it is necessary to apply such measures that would prevent the occurrence of severe fires and ensure the protection of personnel and the general public from the effects of a radiation accident.

scholarly journals Structural Modeling and Dynamic Analysis of a Nuclear Reactor Building

2020 ◽  
Author(s):  
Evrim Oyguc ◽  
Abdul Hayır ◽  
Resat Oyguc
Keyword(s):  
Nonlinear Dynamic ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Nuclear Reactor ◽  
Energy Sources ◽  
Finite Element Program ◽  
Design Spectrum ◽  
Reactor Building ◽  
Set Up

Increasing energy demand urge the developing countries to consider different types of energy sources. Owing the fact that the energy production capacity of renewable energy sources is lower than a nuclear power plant, developed countries like US, France, Japan, Russia and China lead to construct nuclear power plants. These countries compensate 80% of their energy need from nuclear power plants. Further, they periodically conduct tests in order to assess the safety of the existing nuclear power plants by applying impact type loads to the structures. In this study, a sample third-generation nuclear reactor building has been selected to assess its seismic behavior and to observe the crack propagations of the prestressed outer containment. First, a 3D model has been set up using ABAQUS finite element program. Afterwards, modal analysis is conducted to determine the mode shapes. Nonlinear dynamic time history analyses are then followed using an artificial strong ground motion which is compatible with the mean design spectrum of the previously selected ground motions that are scaled to Eurocode 8 Soil type B design spectrum. Results of the conducted nonlinear dynamic analyses are considered in terms of stress distributions and crack propagations.

scholarly journals Assessment of water hammer effects on boiling water nuclear reactor core dynamics

2007 ◽  
Vol 22 (1) ◽  
pp. 18-33 ◽  
Author(s):  
Anis Bousbia-Salah
Keyword(s):  
Pressure Wave ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Reactor Core ◽  
Water Hammer ◽  
Pressure Wave Amplitude ◽  
Sensitivity Studies ◽  
Rapid Transients ◽  
Complex Phenomena

Complex phenomena, as water hammer transients, occurring in nuclear power plants are still not very well investigated by the current best estimate computational tools. Within this frame work, a rapid positive reactivity addition into the core generated by a water hammer transient is considered. The numerical simulation of such phenomena was carried out using the coupled RELAP5/PARCS code. An over all data comparison shows good agreement between the calculated and measured core pressure wave trends. However, the predicted power response during the excursion phase did not correctly match the experimental tendency. Because of this, sensitivity studies have been carried out in order to identify the most influential parameters that govern the dynamics of the power excursion. After investigating the pressure wave amplitude and the void feed back responses, it was found that the disagreement between the calculated and measured data occurs mainly due to the RELAP5 low void condensation rate which seems to be questionable during rapid transients. .

scholarly journals Simulation of Steady States of Helium Loop at Long Time Scenarios

2020 ◽  
Vol 328 ◽  
pp. 01009
Author(s):  
František Világi ◽  
Branislav Knížat ◽  
Róbert Olšiak ◽  
Marek Mlkvik ◽  
Peter Mlynár ◽  
...  
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Reactor ◽  
Natural Circulation ◽  
Heat Removal ◽  
Iteration Process ◽  
Heat Accumulation ◽  
Proposed Model ◽  
Long Time ◽  
Convection Cooling

The natural circulation helium loop is an experimental facility designed for the research of the possibility of utilizing natural convection cooling for the case of decay heat removal from a fast nuclear reactor. This concept would bring an improved automated safety system for future nuclear power plants operating a gas-cooled reactor. The article presents a new possibility of direct use of energy conservation laws in a 1D simulation of natural circulation loops. The calculation is performed by a triple iteration process, nested into each other. The results of the calculations showed good agreement with the measurements at steady state. A calculation with the proposed model at unsteady state is not yet possible, especially because of the exclusion of heat accumulation into the material.

Sign in / Sign up

Export Citation Format

Share Document