scholarly journals Advanced Design and Optimal Sizing of Hydrostatic Transmission Systems

Actuators ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 243
Author(s):  
Xiaofan Guo ◽  
Andrea Vacca
Keyword(s):  
Power Saving ◽  
Cost Effective ◽  
Operating Conditions ◽  
Genetic Optimization ◽  
Heavy Duty ◽  
Construction Machinery ◽  
Hydrostatic Transmission ◽  
High Efficient ◽  
Novel Method ◽  
Hydrostatic Transmissions

This paper presents a novel method for designing and sizing high-efficient hydrostatic transmissions (HTs) for heavy duty propulsion applications such as agricultural and construction machinery. The proposed method consists in providing cost effective HT architectures that maximizes efficiency at the most frequent operating conditions of the transmission, as opposed to the traditional HT design methods based on the most demanding requirements of the system. The sizing method is based on a genetic optimization algorithm for calculating the optimal displacement of the main units of the HT to maximizes the efficiency in the most frequent operating conditions of the vehicle. A simulation model for HTs is built in MATLAB/Simulink® environment to test three different circuit alternatives for basic HTs. Considering a particular 250 kW heavy-duty application for which drive cycle data were available, this study shows great improvement in energy efficiency (14%) and power saving (20.1%) at frequent operating conditions while still achieving the corner power condition.

CAD Of Anticorrosive Protection Of Steel Structures

2019 ◽  
pp. 18-23
Keyword(s):  
Protective Coating ◽  
Computer Aided Design ◽  
Steel Structures ◽  
Cost Effective ◽  
Operating Conditions ◽  
Computational Tool ◽  
Protection Method ◽  
Cost Effective Method ◽  
The Cost ◽  
Aided Design

The choice of cost-effective method of anticorrosive protection of steel structures is an urgent and time consuming task, considering the significant number of protection ways, differing from each other in the complex of technological, physical, chemical and economic characteristics. To reduce the complexity of solving this problem, the author proposes a computational tool that can be considered as a subsystem of computer-aided design and used at the stage of variant and detailed design of steel structures. As a criterion of the effectiveness of the anti-corrosion protection method, the cost of the protective coating during the service life is accepted. The analysis of existing methods of steel protection against corrosion is performed, the possibility of their use for the protection of the most common steel structures is established, as well as the estimated period of effective operation of the coating. The developed computational tool makes it possible to choose the best method of protection of steel structures against corrosion, taking into account the operating conditions of the protected structure and the possibility of using a protective coating.

Infrared Emission Spectroscopy as a Reliability Tool

1999 ◽  
Author(s):  
Q. Kim ◽  
S. Kayali
Keyword(s):  
Spatial Resolution ◽  
Emission Spectroscopy ◽  
Hot Spot ◽  
Cost Effective ◽  
Infrared Emission ◽  
Test System ◽  
Operating Conditions ◽  
Yield Enhancement ◽  
Infrared Emission Spectroscopy ◽  
Channel Temperature

Abstract In this paper, we report on a non-destructive technique, based on IR emission spectroscopy, for measuring the temperature of a hot spot in the gate channel of a GaAs metal/semiconductor field effect transistor (MESFET). A submicron-size He-Ne laser provides the local excitation of the gate channel and the emitted photons are collected by a spectrophotometer. Given the state of our experimental test system, we estimate a spectral resolution of approximately 0.1 Angstroms and a spatial resolution of approximately 0.9 μm, which is up to 100 times finer spatial resolution than can be obtained using the best available passive IR systems. The temperature resolution (<0.02 K/μm in our case) is dependent upon the spectrometer used and can be further improved. This novel technique can be used to estimate device lifetimes for critical applications and measure the channel temperature of devices under actual operating conditions. Another potential use is cost-effective prescreening for determining the 'hot spot' channel temperature of devices under normal operating conditions, which can further improve device design, yield enhancement, and reliable operation. Results are shown for both a powered and unpowered MESFET, demonstrating the strength of our infrared emission spectroscopy technique as a reliability tool.

scholarly journals A Novel Method for the Preparation of Fibrous CeO2–ZrO2–Y2O3 Compacts for Thermochemical Cycles

Crystals ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 885
Author(s):  
Nicole Knoblauch ◽  
Peter Mechnich
Keyword(s):  
Large Scale ◽  
Preparation Method ◽  
Cost Effective ◽  
High Porosity ◽  
Thermochemical Cycles ◽  
Redox Cycles ◽  
Redox Kinetics ◽  
Direct Infiltration ◽  
Novel Method ◽  
Functional Components

Zirconium-Yttrium-co-doped ceria (Ce0.85Zr0.13Y0.02O1.99) compacts consisting of fibers with diameters in the range of 8–10 µm have been successfully prepared by direct infiltration of commercial YSZ fibers with a cerium oxide matrix and subsequent sintering. The resulting chemically homogeneous fiber-compacts are sinter-resistant up to 1923 K and retain a high porosity of around 58 vol% and a permeability of 1.6–3.3 × 10−10 m² at a pressure gradient of 100–500 kPa. The fiber-compacts show a high potential for the application in thermochemical redox cycling due its fast redox kinetics. The first evaluation of redox kinetics shows that the relaxation time of oxidation is five times faster than that of dense samples of the same composition. The improved gas exchange due to the high porosity also allows higher reduction rates, which enable higher hydrogen yields in thermochemical water-splitting redox cycles. The presented cost-effective fiber-compact preparation method is considered very promising for manufacturing large-scale functional components for solar-thermal high-temperature reactors.

scholarly journals Removal of heavy metal ions from wastewater: a comprehensive and critical review

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Naef A. A. Qasem ◽  
Ramy H. Mohammed ◽  
Dahiru U. Lawal
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Large Volume ◽  
Heavy Metal Ions ◽  
Membrane Separation ◽  
Cost Effective ◽  
Operating Conditions ◽  
Future Research ◽  
Sludge Formation ◽  
Metals Removal

AbstractRemoval of heavy metal ions from wastewater is of prime importance for a clean environment and human health. Different reported methods were devoted to heavy metal ions removal from various wastewater sources. These methods could be classified into adsorption-, membrane-, chemical-, electric-, and photocatalytic-based treatments. This paper comprehensively and critically reviews and discusses these methods in terms of used agents/adsorbents, removal efficiency, operating conditions, and the pros and cons of each method. Besides, the key findings of the previous studies reported in the literature are summarized. Generally, it is noticed that most of the recent studies have focused on adsorption techniques. The major obstacles of the adsorption methods are the ability to remove different ion types concurrently, high retention time, and cycling stability of adsorbents. Even though the chemical and membrane methods are practical, the large-volume sludge formation and post-treatment requirements are vital issues that need to be solved for chemical techniques. Fouling and scaling inhibition could lead to further improvement in membrane separation. However, pre-treatment and periodic cleaning of membranes incur additional costs. Electrical-based methods were also reported to be efficient; however, industrial-scale separation is needed in addition to tackling the issue of large-volume sludge formation. Electric- and photocatalytic-based methods are still less mature. More attention should be drawn to using real wastewaters rather than synthetic ones when investigating heavy metals removal. Future research studies should focus on eco-friendly, cost-effective, and sustainable materials and methods.

Experimental Investigation of a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
Jinlong Liu ◽  
Hemanth Kumar Bommisetty ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Compression Ignition ◽  
Heavy Duty ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Cycle Variation ◽  
Spark Timing ◽  
Ci Engines

Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.

Potential of the Variable Valve Actuation (VVA) Strategy on a Heavy Duty CNG Engine

2014 ◽  
Author(s):  
Mirko Baratta ◽  
Roberto Finesso ◽  
Daniela Misul ◽  
Ezio Spessa ◽  
Yifei Tong ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Operating Conditions ◽  
Intake Valve ◽  
Heavy Duty ◽  
Engine Emissions ◽  
Variable Valve Actuation ◽  
Cng Engine ◽  
Variable Valve ◽  
Working Point ◽  
Valve Actuation

The environmental concerns officially aroused in 1970s made the control of the engine emissions a major issue for the automotive industry. The corresponding reduction in fuel consumption has become a challenge so as to meet the current and future emission legislations. Given the increasing interest retained by the optimal use of a Variable Valve Actuation (VVA) technology, the present paper investigates into the potentials of combining the VVA solution to CNG fuelling. Experiments and simulations were carried out on a heavy duty 6-cylinders CNG engine equipped with a turbocharger displaying a twin-entry waste-gate-controlled turbine. The analysis aimed at exploring the potentials of the Early Intake Valve Closure (EIVC) mode and to identify advanced solutions for the combustion management as well as for the turbo-matching. The engine model was developed within the GT-Power environment and was finely tuned to reproduce the experimental readings under steady state operations. The 0D-1D model was hence run to reproduce the engine operating conditions at different speeds and loads and to highlight the effect of the VVA on the engine performance as well as on the fuel consumption and engine emissions. Pumping losses proved to reduce to a great extent, thus decreasing the brake specific fuel consumption (BSFC) with respect to the throttled engine. The exhaust temperature at the turbine inlet was kept to an almost constant value and minor variations were allowed. This was meant to avoid an excessive worsening in the TWC working conditions, as well as deterioration in the turbocharger performance during load transients. The numerical results also proved that full load torque increases can be achieved by reducing the spark advance so that a higher enthalpy is delivered to the turbocharger. Similar torque levels were also obtained by means of Early Intake Valve Closing strategy. For the latter case, negligible penalties in the fuel consumption were detected. Moreover, for a given combustion phasing, the IVC angle directly controls the mass-flow rate and thus the torque. On the other hand, a slight dependence on the combustion phasing can be detected at part load. Finally, the simulations assessed for almost constant fuel consumption for a wide range of IVC and SA values. Specific attention was also paid to the turbocharger group functioning and to its correct matching to the engine working point. The simulations showed that the working point on the compressor map can be optimized by properly setting the spark advance (SA) as referred to the adopted intake-valve closing angle. It is anyhow worth observing that the engine high loads set a constraint deriving from the need to meet the limits on the peak firing pressure (PFP), thus limiting the possibility to optimize the working point once the turbo-matching is defined.

scholarly journals Influence of the diesel pilot injector configuration on ethanol combustion and performance of a heavy-duty direct injection engine

2021 ◽  
pp. 146808742110012
Author(s):  
Nicola Giramondi ◽  
Anders Jäger ◽  
Daniel Norling ◽  
Anders Christiansen Erlandsson
Keyword(s):  
Direct Injection ◽  
Engine Performance ◽  
High Load ◽  
Operating Conditions ◽  
Injection System ◽  
Injection Timing ◽  
Diesel Combustion ◽  
Heavy Duty ◽  
Pure Ethanol ◽  
Ethanol Combustion

Thanks to its properties and production pathways, ethanol represents a valuable alternative to fossil fuels, with potential benefits in terms of CO2, NOx, and soot emission reduction. The resistance to autoignition of ethanol necessitates an ignition trigger in compression-ignition engines for heavy-duty applications, which in the current study is a diesel pilot injection. The simultaneous direct injection of pure ethanol as main fuel and diesel as pilot fuel through separate injectors is experimentally investigated in a heavy-duty single cylinder engine at a low and a high load point. The influence of the nozzle hole number and size of the diesel pilot injector on ethanol combustion and engine performance is evaluated based on an injection timing sweep using three diesel injector configurations. The tested configurations have the same geometric total nozzle area for one, two and four diesel sprays. The relative amount of ethanol injected is swept between 78 – 89% and 91 – 98% on an energy basis at low and high load, respectively. The results show that mixing-controlled combustion of ethanol is achieved with all tested diesel injector configurations and that the maximum combustion efficiency and variability levels are in line with conventional diesel combustion. The one-spray diesel injector is the most robust trigger for ethanol ignition, as it allows to limit combustion variability and to achieve higher combustion efficiencies compared to the other diesel injector configurations. However, the two- and four-spray diesel injectors lead to higher indicated efficiency levels. The observed difference in the ethanol ignition dynamics is evaluated and compared to conventional diesel combustion. The study broadens the knowledge on ethanol mixing-controlled combustion in heavy-duty engines at various operating conditions, providing the insight necessary for the optimization of the ethanol-diesel dual-injection system.

The Use of Electrostatic Charge Measurements as an Early Warning of Distress in Heavy-Duty Gas Turbines

2001 ◽  
Author(s):  
G. L. Lapini ◽  
M. Zippo ◽  
G. Tirone
Keyword(s):  
Monitoring System ◽  
Early Warning ◽  
Gas Turbines ◽  
Electrostatic Charge ◽  
Electric Utility ◽  
Operating Conditions ◽  
System Response ◽  
Jet Engines ◽  
Heavy Duty ◽  
Demonstration Program

The idea of measuring the electrostatic charge associated with the debris contained in the exhaust gases of a gas turbine (sometimes named EDMS, Engine Debris Monitoring System, or EEMS, Electrostatic Engine Monitoring System) has been demonstrated by several authors as an interesting diagnostic tool for the early warning of possible internal distresses (rubs, coating wear, hot spots in combustors, improper combustion, etc.) especially for jet engines or aeroderivative gas turbines. While potentially applicable to machines of larger size, the possibility of transferring this monitoring technology to heavy-duty gas turbines, which have exhaust ducts much bigger in size and different operating conditions, should be demonstrated. The authors present a synthesis of their experience and of the most significant data collected during a demonstration program performed on behalf of ENEL, the main Italian electric utility. The purpose of this program was to test this concept in real operating conditions on large turbines, and hence to evaluate the influence of the operating conditions on the system response and to assess its sensitivity to possible distresses. A good amount of testing has been performed, during this program, both on a full scale combustion rig, and on two machines rated at about 120 MW, during their normal and purposely perturbed operating conditions in a power plant. The authors, on the basis of the encouraging results obtained to date, comment on the work still required to bring this technology to full maturity.

Sign in / Sign up

Export Citation Format

Share Document