scholarly journals On the Directivity of Acoustic Waves Generated by the Angle Beam Wedge Actuator in Thin-Walled Structures

Actuators ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 64 ◽  
Author(s):  
Sergey Shevtsov ◽  
Valery Chebanenko ◽  
Maria Shevtsova ◽  
Evgenia Kirillova ◽  
Evgeny Rozhkov
Keyword(s):  
Experimental Study ◽  
Acoustic Waves ◽  
Lamb Waves ◽  
Oscillation Amplitude ◽  
Element Model ◽  
Propagation Length ◽  
Thin Walled Structures ◽  
Plastic Panel ◽  
Thin Walled ◽  
The Waves

The paper aims to develop improved acoustic-based structural health monitoring (SHM) and nondestructive evaluation (NDE) techniques, which provide the waves directivity emitted by the angle beam wedge actuators in thin-walled structures made of plastic materials and polymeric composites. Our investigation includes the dispersive analysis of the waves that can be excited in the studied plastic panel. Its results allowed to find two kinds of generated acoustic waves—anti-symmetric Lamb waves (A0) and shear horizontally polarized SH waves (SS0). The bounds of the chosen frequency range for the experimental and numerical studies were accepted as a compromise between the desire to obtain a high defect resolution by generating short waves, their adjustable directivity, and maximum propagation length. The finite element model for the transducer was built by using the results of an actuator structure experimental study. The frequency response functions for the actuator current and oscillation amplitude of the footprint surface demonstrated good agreement. The found eigenfrequencies of the actuator’s structure were used for the numerical and experimental study of the Lamb and SH wave generation and propagation in a thin-walled plastic panel. Our results convincingly demonstrated the satisfactory directivity of the actuated waves at their excitation on the frequencies that corresponded to the natural modes of the actuator oscillation. The authors assume that an efficient use of the proposed technique for other analyzed quasi-isotropic materials and applied actuators can be provided by preliminary research using a similar approach and methods presented in this article.

scholarly journals On the Directivity of Acoustic Waves Generated by the Angle Beam Wedge Actuator in Thin Walled Structures

2019 ◽  
Author(s):  
Sergey Shevtsov ◽  
Valery Chebanenko ◽  
Maria Shevtsova ◽  
Evgenia Kirillova ◽  
Evgeny Rozhkov
Keyword(s):  
Experimental Study ◽  
Acoustic Waves ◽  
Lamb Waves ◽  
Oscillation Amplitude ◽  
Element Model ◽  
Propagation Length ◽  
Thin Walled Structures ◽  
Plastic Panel ◽  
Thin Walled ◽  
The Waves

The paper is aimed to develop an improved acoustic-based Structural Health Monitoring (SHM) and Non-Destructive Evaluation (NDE) techniques, which provide the waves directivity emitting by the angle-beam wedge actuators in the thin-walled structures made of plastic materials and polymeric composites. Our investigation includes the dispersive analysis of the waves that can be excited in the studied plastic panel. Its results allowed to find two kinds of the generated acoustic waves - anti-symmetric Lamb waves A0 and shear horizontally polarized SH waves SS0. The bounds of the chosen frequency range for the experimental and numerical studies were accepted as a compromise between the desire to obtain high defects resolution by generating short waves, their adjustable directivity and maximum propagation length. The finite element model for the transducer was built by using the results of actuator structure experimental study. The frequency response functions for the actuator current and oscillation amplitude of the footprint surface demonstrated good agreement. The found eigenfrequencies of actuator's structure were used for the numerical and experimental study of the Lamb and SH wave generation and propagation in a thin-walled plastic panel. Our results convincingly demonstrated the satisfactory directivity of the actuated waves at their excitation on the frequencies that corresponded to the natural modes of the actuator oscillation. The authors assume that an efficient use of the proposed technique for other analyzed quasi-isotropic materials and applied actuators can be provided by a preliminary research using the similar approach and methods presented in this article.

scholarly journals Dynamic Analysis of Tapered Thin-Walled Beams Using Spectral Finite Element Method

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Yiping Shen ◽  
Zhijun Zhu ◽  
Songlai Wang ◽  
Gang Wang
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Wind Turbine ◽  
Element Model ◽  
Rotor Blades ◽  
Mode Shapes ◽  
Modal Frequency ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Spectral Finite Element

Tapered thin-walled structures have been widely used in wind turbine and rotor blade. In this paper, a spectral finite element model is developed to investigate tapered thin-walled beam structures, in which torsion related warping effect is included. First, a set of fully coupled governing equations are derived using Hamilton’s principle to account for axial, bending, and torsion motion. Then, the differential transform method (DTM) is applied to obtain the semianalytical solutions in order to formulate the spectral finite element. Finally, numerical simulations are conducted for tapered thin-walled wind turbine rotor blades and validated by the ANSYS. Modal frequency results agree well with the ANSYS predictions, in which approximate 30,000 shell elements were used. In the SFEM, one single spectral finite element is needed to perform such calculations because the interpolation functions are deduced from the exact semianalytical solutions. Coupled axial-bending-torsion mode shapes are obtained as well. In summary, the proposed spectral finite element model is able to accurately and efficiently to perform the modal analysis for tapered thin-walled rotor blades. These modal frequency and mode shape results are important to carry out design and performance evaluation of the tapered thin-walled structures.

Damage Detection Using Lamb Waves (Review)

2014 ◽  
Vol 1028 ◽  
pp. 161-166 ◽  
Author(s):  
Zai Lin Yang ◽  
Hamada M. Elgamal ◽  
Yao Wang
Keyword(s):  
Damage Detection ◽  
Health Monitoring ◽  
Guided Waves ◽  
Damage Identification ◽  
Lamb Waves ◽  
Long Distance ◽  
The Past ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Analytical Complexity

Several techniques have been researched for detecting damage in plates. Each of these techniques offers their own unique advantages in detecting certain types of damage with various levels of analytical complexity. Lamb waves are guided waves that exist in thin walled structures. Because this type of wave can travel long distance with little attenuation, they have been studied intensively for structural health monitoring, especially in the past few decades. This paper presents an overview of using the Lamb waves in damage detection including the theory of lamb waves and the lamb-wave-based damage identification.

Detection of defects in thin-walled structures by means of Lamb waves

2012 ◽  
Author(s):  
Hauke Gravenkamp ◽  
Albert A. Saputra ◽  
Chongmin Song ◽  
Jens Prager
Keyword(s):  
Lamb Waves ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
Detection Of Defects

scholarly journals Numerical Models of the Connection of Thin-Walled Z-Profile Roof Purlins

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6573
Author(s):  
Přemysl Pařenica ◽  
Petr Lehner ◽  
Jiří Brožovský ◽  
Martin Krejsa
Keyword(s):  
Cross Section ◽  
Numerical Models ◽  
Element Model ◽  
Cross Sectional ◽  
Physical Test ◽  
Thin Walled Structures ◽  
Practical Design ◽  
Thin Walled ◽  
Bolt Connection ◽  
Experimental Preparation

High thin-walled purlins of Z cross-section are important elements in steel wide-span structures. Their behaviour is influenced by many variables that need to be examined for every specific case. Their practical design thus requires extended knowledge of their behaviour for the possible configurations and dimensions. Numerical analysis verified by experimental investigation can thus enrich such knowledge. Numerical models have the advantage of repeatability and the ability to offer parametric changes. The parametric study presented shows a detailed description of a finite element model of thin-walled cross-sectional roof purlins connected to other roof elements. Models include various approaches to modelling bolt connection. Two schemes of purlins, with and without cleats, are presented. The results of different approaches in numerical modelling are compared with the results of a physical test on a real structure. The article shows a significant agreement in the case of specific approaches and points out the differences with others. The results can be helpful in terms of how to approach the modelling of thin-walled structures and the effective approach to experimental preparation.

Nonlinear Response of C/C Composite Laminated Panels with Temperature Gradients under Guassian Pressure Waves

2013 ◽  
Vol 470 ◽  
pp. 1062-1068 ◽  
Author(s):  
Yun Dong Sha ◽  
Xiao Bo Jie ◽  
Lin Zhu
Keyword(s):  
Thermal Protection ◽  
Element Model ◽  
Carbon Composite ◽  
Temperature Gradients ◽  
System Response ◽  
Equivalent Linearization ◽  
Total System ◽  
Thin Walled Structures ◽  
Thin Walled ◽  
High Level

Carbon-Carbon composite material is widely used as the thermal protection systems (TPS) of hypersonic vehicles for its special mechanical and heat-proof capabilities. The thin-walled structures with this kind of materials would exhibit large displacement response under high-level acoustic loads. Usually, the external heating is non-uniform. In the paper, a finite element model for analyzing nonlinear random dynamic behaviors of Carbon-Carbon composite panels with temperature gradients under Guassian sound excitation is founded. The total system response is decomposed into the time-independent component and the time-dependent component, using the equivalent linearization technique. Numerical results include root mean square (RMS) values of maximum deflections, time histories and power spectrum densities (PSD) of the deflection response. The results obtained in this paper can contribute to the thorough understanding of thermo-acoustic response of composite thin-walled structures.

Influence of the Subtended Angle on the Behavior of Folded Tape Springs

2018 ◽  
Author(s):  
Marinus G. de Jong ◽  
Werner W. P. J. van de Sande ◽  
Just L. Herder
Keyword(s):  
Finite Element ◽  
Cross Section ◽  
Strain Energy ◽  
Element Model ◽  
Constant Cross Section ◽  
Curvature Analysis ◽  
Thin Walled Structures ◽  
Constant Radius ◽  
Thin Walled ◽  
Force Generator

Tape springs are thin-walled structures with zero longitudinal and constant transverse curvature. Folding them twice and connecting both ends creates a tape loop which acts as a linear guide. When using a tape spring with a non-constant cross-section, a force generator can be created. At this time there is insufficient understanding of the influence of the tape spring’s cross-section on its behavior. This study investigates the influence of the subtended angle on the tape spring’s behavior, especially the energy distribution and the fold radius. A tape spring is once folded in a finite element model. By performing a curvature analysis of this folded geometry, the different regions within a tape spring are identified. This information is used to identify the amount of strain energy of each region. Finally, the fold radius and fold angle are determined by analyzing the geometry of the bent region. The analysis showed that the energy within the transition regions cannot be neglected. The energy within these regions as ratio of the total energy and the length of the transition regions both increase with the subtended angle. It is also shown that the fold radius is not constant when the subtended angle is small. Therefore, when designing a force generator using tape loops, the energy within the transition regions should be taken into account. The subtended angle should not be small to ensure a constant radius.

scholarly journals Nonpenetrating Damage Identification Using Hybrid Lamb Wave Modes from Hilbert-Huang Spectrum in Thin-Walled Structures

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Zijian Wang ◽  
Pizhong Qiao ◽  
Binkai Shi
Keyword(s):  
Lamb Wave ◽  
Damage Identification ◽  
Lamb Waves ◽  
Wave Mode ◽  
Thin Walled Structures ◽  
Damage Indices ◽  
Thin Walled ◽  
Experimental Validations ◽  
The One ◽  
Wave Modes

Lamb waves have shown promising advantages for damage identification in thin-walled structures. Multiple modes of Lamb wave provide diverse sensitivities to different types of damage. To sufficiently utilize damage-related wave features, damage indices were developed by using hybrid Lamb wave modes from Hilbert-Huang spectra. Damage indices were defined as surface integrals of Hilbert-Huang spectra on featured regions determined by time and frequency windowing. The time windowing was performed according to individual propagation velocity of different Lamb wave mode, while the frequency windowing was performed according to the frequency of excitation. By summing damage indices for all transmitter-receiver pairs, pixels were calculated to reconstruct a damage map to characterize the degree of damage at each location on structure. Both numerical and experimental validations were conducted to identify a nonpenetrating damage. The results demonstrated that the proposed damage indices using hybrid Lamb wave modes are more sensitive and robust than the one using single Lamb wave mode.

Sign in / Sign up

Export Citation Format

Share Document