scholarly journals A Displacement Measuring Interferometer Based on a Frequency-Locked Laser Diode with High Modulation Frequency

2020 ◽  
Vol 10 (8) ◽  
pp. 2693
Author(s):  
Thanh Tung Vu ◽  
Hong Hai Hoang ◽  
Toan Thang Vu ◽  
Ngoc Tam Bui
Keyword(s):  
Frequency Modulation ◽  
High Speed ◽  
Modulation Frequency ◽  
Laser Source ◽  
Interference Signal ◽  
Modulation Amplitude ◽  
Hyperfine Component ◽  
Synchronous Detection ◽  
High Modulation ◽  
Uncertainty Of Measurements

Laser interferometers can achieve a nanometer-order uncertainty of measurements when their frequencies are locked to the reference frequencies of the atom or molecule transitions. There are three types of displacement-measuring interferometers: homodyne, heterodyne, and frequency modulation (FM) interferometers. Among these types of interferometer, the FM interferometer has many advantageous features. The interference signal is a series of time-dependent harmonics of modulation frequency, so the phase shift can be detected accurately using the synchronous detection method. Moreover, the FM interferometer is the most suitable for combination with a frequency-locked laser because both require frequency modulation. In previous research, low modulation frequencies at some tens of kHz have been used to lock the frequency of laser diodes (LDs). The low modulation frequency for the laser source means that the maximum measurement speed of the FM interferometers is limited. This paper proposes a novel contribution regarding the application of a high-frequency modulation for an LD to improve both the frequency stability of the laser source and the measurement speed of the FM interferometer. The frequency of the LD was locked to an I2 hyperfine component at 1 MHz modulation frequency. A high bandwidth lock-in amplifier was utilized to detect the saturated absorption signals of the I2 hyperfine structure and induce the signal to lock the frequency of the LD. The locked LD was then used for an FM displacement measuring interferometer. Moreover, a suitable modulation amplitude that affected the signal-to-noise ratio of both the I2 absorption signal and the harmonic intensity of the interference signal was determined. In order to verify the measurement resolution of the proposed interferometer, the displacement induced by a piezo electric actuator was concurrently measured by the interferometer and a capacitive sensor. The difference of the displacement results was less than 20 nm. To evaluate the measurement speed, the interferometer was used to measure the axial error of a high-speed spindle at 500 rpm. The main conclusion of this study is that a stable displacement interferometer with high accuracy and a high measurement speed can be achieved using an LD frequency locked to an I2 hyperfine transition at a high modulation frequency.

scholarly journals Axial Error of Spindle Measurements Using a High-Frequency-Modulated Interferometer

Crystals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 801
Author(s):  
Thanh-Trung Nguyen ◽  
Thanh-Tung Vu ◽  
Thanh-Dong Nguyen ◽  
Toan-Thang Vu
Keyword(s):  
High Precision ◽  
Modulation Frequency ◽  
Zeeman Effect ◽  
Machining Process ◽  
Measuring System ◽  
Laser Source ◽  
Small Displacement ◽  
Interference Signal ◽  
High Modulation ◽  
The Difference

In this paper, a novel, compact, and high-precision axial error measurement using a frequency-modulated interferometer is developed. Normally, heterodyne interferometers are a powerful system for small displacement measurements due to their property of being less sensitive to temperature and pressure variations. However, the maximum measurement speed of the heterodyne interferometer is around 5 m/s because it is usually limited by the difference in frequency between the two components of the laser beam, which is no larger than 3 MHz or 20 MHz corresponding laser source based on the Zeeman effect and acousto-optic modulator, respectively. The proposed measuring system is realized by modulating the frequency of the laser diode source at a high modulation frequency and using lock-in amplifiers to extract the harmonics of the interference signal. The measurement speed is proportional to the modulation frequency. Thus, the higher the modulation frequency, the higher the measuring speed attains. The frequency-modulated interferometer is then applied to measure the axial error of an ultra-precision spindle. The proposed system can be a capable solution for noncontact and high-precision spindle error measurements in the machining process.

Quantitative FM Spectroscopy at High Temperatures: The Detection of 1CH2 behind Shock Waves

2000 ◽  
Vol 214 (12) ◽  
Author(s):  
G. Friedrichs ◽  
H.Gg. Wagner
Keyword(s):  
High Temperature ◽  
Shock Waves ◽  
High Temperatures ◽  
Frequency Modulation ◽  
Modulation Frequency ◽  
Optical Power ◽  
Time Resolved ◽  
Signal Conversion ◽  
High Modulation ◽  
Singlet Methylene

The technique of time resolved frequency modulation (FM) spectroscopy has been shown to provide a very sensitive means to detect small radicals behind shock waves. Features of high temperature FM spectroscopy behind shock waves will be discussed and a general signal conversion procedure to carry out quantitative concentration measurements will be presented.Using a high modulation frequency, a high modulation index and high total optical power, singlet methylene radicals (α

HIGH SPEED SEMICONDUCTOR LASERS

1994 ◽  
Vol 05 (01) ◽  
pp. 1-44 ◽  
Author(s):  
RADHAKRISHNAN NAGARAJAN ◽  
DANIEL TAUBER ◽  
JOHN E. BOWERS
Keyword(s):  
Quantum Well ◽  
Semiconductor Lasers ◽  
Dynamic Characteristics ◽  
Frequency Modulation ◽  
High Speed ◽  
Carrier Transport ◽  
Modulation Frequency ◽  
Signal Transmission ◽  
Photon Density ◽  
Intensity Noise

The strategy and methods to design high speed semiconductor lasers are reviewed here. The formalism for the analysis of intensity modulation, frequency modulation and intensity noise in quantum well lasers is first derived. Using this formalism the process of optimizing the laser structure for high speed operation is presented. In addition to the conventional factors such as the differential gain, photon density, photon lifetime and device parasitics, we also review the critical effects of carrier transport and microwave signal transmission on the dynamic characteristics and design of high speed semiconductor lasers.

A High Speed and Ultra Long-Haul Radio-Over-Fiber System Employing Dual Photoelectric Arms Coherent Modulation and Optical Duo-Binary Coding

2014 ◽  
Vol 988 ◽  
pp. 544-547
Author(s):  
Guang Li
Keyword(s):  
High Speed ◽  
Continuous Wave ◽  
Single Mode ◽  
Fiber Amplifier ◽  
Radio Over Fiber ◽  
Laser Source ◽  
Signal Spectrum ◽  
Fiber System ◽  
Binary Coding ◽  
Coherent Modulation

A novel high speed and ultra long-haul radio-over-fiber (ROF) system based on Dual Photoelectric Arms Coherent Modulation (DPACM) and Optical Duo-Binary Coding (ODBC) is proposed, and demonstrated. The signal spectrum bandwidth, generated by ODBC based on the first order DPACM, is half of non-return-to-zero (NRZ ) signal spectrum bandwidth. The secondary order DPACM generates a 40-GHz Millimeter-wave (mm-wave) that is transmitted over fiber (ROF). The simulation results show that, the bit rate can be up to 40 Gbps and the transmission distance is over 1500 Km, based on the ROF system with a 0 dBm continuous-wave laser source, multiple stages Er-Doped Fiber Amplifier (EDFA), a standard single mode fiber (SSMF) with a dispersion of 17 ps/nm/Km and a attenuation of 0.2 dB/Km.

scholarly journals Neuro-Inspired Computing with Spin-VCSELs

2021 ◽  
Vol 11 (9) ◽  
pp. 4232
Author(s):  
Krishan Harkhoe ◽  
Guy Verschaffelt ◽  
Guy Van der Sande
Keyword(s):  
Processing Speed ◽  
Delay Time ◽  
High Speed ◽  
State Of The Art ◽  
Polarization Modulation ◽  
Time Interval ◽  
Computing Technique ◽  
High Modulation ◽  
Short Time ◽  
Modulation Speed

Delay-based reservoir computing (RC), a neuromorphic computing technique, has gathered lots of interest, as it promises compact and high-speed RC implementations. To further boost the computing speeds, we introduce and study an RC setup based on spin-VCSELs, thereby exploiting the high polarization modulation speed inherent to these lasers. Based on numerical simulations, we benchmarked this setup against state-of-the-art delay-based RC systems and its parameter space was analyzed for optimal performance. The high modulation speed enabled us to have more virtual nodes in a shorter time interval. However, we found that at these short time scales, the delay time and feedback rate heavily influence the nonlinear dynamics. Therefore, and contrary to other laser-based RC systems, the delay time has to be optimized in order to obtain good RC performances. We achieved state-of-the-art performances on a benchmark timeseries prediction task. This spin-VCSEL-based RC system shows a ten-fold improvement in processing speed, which can further be enhanced in a straightforward way by increasing the birefringence of the VCSEL chip.

Sources of the Scalp-Recorded Amplitude-Modulation Following Response

2002 ◽  
Vol 13 (04) ◽  
pp. 188-204 ◽  
Author(s):  
Shigeyuki Kuwada ◽  
Julia S. Anderson ◽  
Ranjan Batra ◽  
Douglas C. Fitzpatrick ◽  
Natacha Teissier ◽  
...  
Keyword(s):  
Animal Model ◽  
Amplitude Modulation ◽  
Single Unit ◽  
Modulation Frequency ◽  
Multiple Sources ◽  
High Modulation ◽  
Before And After ◽  
Single Unit Recordings ◽  
Composite Response ◽  
The Brain

The scalp-recorded amplitude-modulation following response (AMFR)” is gaining recognition as an objective audiometric tool, but little is known about the neural sources that underlie this potential. We hypothesized, based on our human studies and single-unit recordings in animals, that the scalp-recorded AMFR reflects the interaction of multiple sources. We tested this hypothesis using an animal model, the unanesthetized rabbit. We compared AMFRs recorded from the surface of the brain at different locations and before and after the administration of agents likely to enhance or suppress neural generators. We also recorded AMFRs locally at several stations along the auditory neuraxis. We conclude that the surface-recorded AMFR is indeed a composite response from multiple brain generators. Although the response at any modulation frequency can reflect the activity of more than one generator, the AMFRs to low and high modulation frequencies appear to reflect a strong contribution from cortical and subcortical sources, respectively.

scholarly journals Neural Rate and Timing Cues for Detection and Discrimination of Amplitude-Modulated Tones in the Awake Rabbit Inferior Colliculus

2007 ◽  
Vol 97 (1) ◽  
pp. 522-539 ◽  
Author(s):  
Paul C. Nelson ◽  
Laurel H. Carney
Keyword(s):  
Inferior Colliculus ◽  
Dynamic Range ◽  
Modulation Depth ◽  
Average Rate ◽  
Modulation Frequency ◽  
Detection Threshold ◽  
Depth Functions ◽  
Depth Discrimination ◽  
High Modulation ◽  
Envelope Processing

Neural responses to amplitude-modulated (AM) tones in the unanesthetized rabbit inferior colliculus (IC) were studied in an effort to establish explicit relationships between physiological and psychophysical measures of temporal envelope processing. Specifically, responses to variations in modulation depth ( m) at the cell’s best modulation frequency, with and without modulation maskers, were quantified in terms of average rate and synchronization to the envelope over the entire perceptual dynamic range of depths. Statistically significant variations in the metrics were used to define neural AM detection and discrimination thresholds. Synchrony emerged at modulation depths comparable with psychophysical AM detection sensitivities in some neurons, whereas the lowest rate-based neural thresholds could not account for psychoacoustical thresholds. The majority of rate thresholds (85%) were −10 dB or higher (in 20 log m), and 16% of the population exhibited no systematic dependence of average rate on m. Neural thresholds for AM detection did not decrease systematically at higher SPLs (as observed psychophysically): thresholds remained constant or increased with level for most cells tested at multiple sound-pressure levels (SPLs). At depths higher than the rate-based detection threshold, some rate modulation-depth functions were sufficiently steep with respect to the across-trial variability of the rate to predict depth discrimination thresholds as low as 1 dB (comparable with the psychophysics). Synchrony, on the other hand, did not vary systematically with m in many cells at high modulation depths. A simple computational model was extended to reproduce several features of the modulation frequency and depth dependence of both transient and sustained pure-tone responders.

scholarly journals Polymer colour converter with very high modulation bandwidth for visible light communications

2017 ◽  
Vol 5 (35) ◽  
pp. 8916-8920 ◽  
Author(s):  
D. A. Vithanage ◽  
A. L. Kanibolotsky ◽  
S. Rajbhandari ◽  
P. P. Manousiadis ◽  
M. T. Sajjad ◽  
...  
Keyword(s):  
Visible Light ◽  
High Speed ◽  
Visible Light Communication ◽  
Modulation Bandwidth ◽  
Visible Light Communications ◽  
Semiconducting Polymer ◽  
High Modulation ◽  
Very High

We report the synthesis, photophysics and application of a novel semiconducting polymer as a colour converter for high speed visible light communication.

Sign in / Sign up

Export Citation Format

Share Document