scholarly journals Comprehensive Study about Effect of Basalt Fiber, Gradation, Nominal Maximum Aggregate Size and Asphalt on the Anti-Cracking Ability of Asphalt Mixtures

2021 ◽  
Vol 11 (5) ◽  
pp. 2289
Author(s):  
Keke Lou ◽  
Xing Wu ◽  
Peng Xiao ◽  
Aihong Kang ◽  
Zhengguang Wu ◽  
...  
Keyword(s):  
Crack Resistance ◽  
Asphalt Mixture ◽  
Basalt Fiber ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Bending Test ◽  
Maximum Aggregate Size ◽  
Test Results ◽  
Cracking Performance ◽  
Test Ideal

There are many parameters that could affect the properties of asphalt mixtures, such as the fiber additive, gradation type, nominal maximum aggregate size (NMAS), and asphalt. To evaluate the influence of these factors on the crack resistance of asphalt mixture, 10 different types of asphalt mixtures were prepared. The indirect tensile asphalt cracking test (IDEAL-CT) and semi-circle bending test (SCB) were adopted to test the anti-cracking ability of the test samples. The parameters of these two test results were also used to conduct the correlation analysis to find the correlation between different parameters, and scanning electron microscope (SEM) test was also used to analyze the micro cracks of asphalt mixture. The results showed that basalt fiber could further enhance the anti-cracking ability of asphalt mixture. Stone matrix asphalt (SMA) showed better anti-cracking performance than Superpave (SUP) asphalt mixtures. The increase in the nominal maximum aggregate size could decrease the anti-cracking ability of asphalt mixtures. Styrene-Butadiene-Styrene (SBS) modified asphalt could better reinforce the anti-cracking ability than pure asphalt. The CTindex of IDEAL-CT test and Flexibility index (FI) value of SCB test results showed better correlation. This paper has certain significance in guiding the design of asphalt mixtures having good crack resistance.

Laboratory Investigate of the Effect of Fine Aggregates on Asphalt Mixture Materials

2011 ◽  
Vol 225-226 ◽  
pp. 577-580
Author(s):  
Yong Ye ◽  
Yi Zhou Cai
Keyword(s):  
Compressive Strength ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Fine Aggregate ◽  
Test Results ◽  
Creep Tests ◽  
Aggregate Gradation ◽  
Static Creep ◽  
Fine Aggregates

The objective of this study is to investigate and evaluate the effect of fine aggregates (aggregate size smaller than or equal to 2.36 mm) on the compressive strength and creep behavior of asphalt mixtures. The variables that are considered in the study include the sizes and gradations of fine aggregate. A kind of standant aggregate gradation and four kinds of reduced aggregate gradation mixture specimens are used. Uniaxial compression and static creep tests were realized at different loading conditions. The test results showed that the different fine aggregate sizes do not result in significant differences in compressive strength and creep values using the same percentage of fine aggregates (38.4%). Only the different gradations showed a little differences for mixtures made with different gradations but same aggregate size (between 2.36 and 1.18 mm).

Evaluation of Small Specimen Geometries for Asphalt Mixture Performance Testing and Pavement Performance Prediction

2017 ◽  
Vol 2631 (1) ◽  
pp. 74-82 ◽  
Author(s):  
Kangjin Lee ◽  
Sonja Pape ◽  
Cassie Castorena ◽  
Y. Richard Kim
Keyword(s):  
Phase Angle ◽  
Dynamic Modulus ◽  
Asphalt Mixture ◽  
Performance Testing ◽  
Aggregate Size ◽  
Pavement Performance ◽  
Maximum Aggregate Size ◽  
Small Specimen ◽  
Test Results ◽  
Multiple Test

The use of small specimen geometries in asphalt mixture performance testing to enable the testing of as-built pavement layers has been gaining attention in recent years. Small specimens could also improve the testing efficiency of laboratory-fabricated specimens by allowing the extraction of multiple test specimens per gyratory-compacted sample. Rigorous assessment of the small specimen geometries is required before the use of such geometries is standardized. In this study, small specimens were evaluated for dynamic modulus and simplified viscoelastic continuum damage fatigue. Three specimen geometries (100-mm- and 38-mm-diameter cylindrical specimens and 25- × 50-mm prismatic specimens) were compared by using five mixtures with a nominal maximum aggregate size (NMAS) ranging from 9.5 to 25.0 mm. The results show that the dynamic modulus and phase angle master curves agreed at low and intermediate temperatures, regardless of the NMAS values of the mixture. At the high temperature, the small specimen dynamic modulus values were slightly higher and the phase angle values were slightly lower than those of the large specimens. The specimen-to-specimen variability for the large and small specimens was comparable. The fatigue test results for the mixtures evaluated were comparable, except for the 25-mm mixture, which proved problematic in the testing of both small and large specimens. Pavement performance was predicted by the layered viscoelastic analysis for critical distresses program by using the test results for the small and large specimens. These results suggest that specimen geometry had a minimal effect on pavement fatigue damage predictions, which indicates promise for the use of small specimen geometries in practice.

Study on High Temperature Performance of Asphalt Mixture Based on Rutting Test

2015 ◽  
Vol 744-746 ◽  
pp. 1316-1319
Author(s):  
Yi Wang ◽  
Wei Li
Keyword(s):  
High Temperature ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Temperature Stability ◽  
Maximum Aggregate Size ◽  
Test Results ◽  
High Temperature Stability ◽  
Modified Asphalt ◽  
Temperature Performance ◽  
Nominal Size

In order to deeply reveal the high temperature stability of asphalt mixture, rutting test was implemented to evaluate the high temperature stability of asphalt mixture, and the evaluation index is dynamic stability. The effect of asphalt type, degree of compaction, gradation type and nominal maximum aggregate size on rutting test results was studied respectively. The results showed that: modified asphalt can improve the high temperature stability of asphalt mixture effectively; the anti-rutting performance of asphalt mixture reduces gradually with decrease of the degree of compaction; the anti-rutting performance of SAC-16 is greater than that of AC-16; and the anti-rutting performance of asphalt mixture is improved with increase of the nominal size of aggregate.

scholarly journals Effects of Fiber Diameter on Crack Resistance of Asphalt Mixtures Reinforced by Basalt Fibers Based on Digital Image Correlation Technology

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7426
Author(s):  
Zhaohui Pei ◽  
Keke Lou ◽  
Heyu Kong ◽  
Bangwei Wu ◽  
Xing Wu ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Crack Resistance ◽  
Digital Image ◽  
Fiber Diameter ◽  
Basalt Fiber ◽  
Asphalt Mixtures ◽  
Image Correlation ◽  
Bending Test ◽  
Basalt Fibers ◽  
The Impact

It is now more popular to use basalt fibers in the engineering programs to reinforce the crack resistance of asphalt mixtures. However, research concerning the impact of the basalt fiber diameter on the macro performance of AC-13 mixtures is very limited. Therefore, in this paper, basalt fibers with three diameters, including 7, 13 and 25 μm, were selected to research the influences of fiber diameter on the crack resistance of asphalt mixtures. Different types of crack tests, such as the low temperature trabecular bending test (LTTB), the indirect tensile asphalt cracking test (IDEAL-CT), and the semi-circular bend test (SCB), were conducted to reveal the crack resistance of AC-13 mixtures. The entire cracking process was recorded through the digital image correlation (DIC) technique, and the displacement cloud pictures, strain, average crack propagation rate (V) and fracture toughness (FT) indicators were used to evaluate the crack inhibition action of the fiber diameter on the mixture. The results showed that the incorporation of basalt fiber substantially improved the crack resistance, slowed down the increase of the displacement, and delayed the fracture time. Basalt fiber with a diameter of 7 μm presented the best enhancement capability on the crack resistance of the AC-13 mixture. The flexibility index (FI) of the SCB test showed a good correlation with V and FT values of DIC test results, respectively. These findings provide theoretical advice for the popularization and engineering application of basalt fibers in asphalt pavement.

scholarly journals Suitability of Fiber Lengths for Hot Mix Asphalt with Different Nominal Maximum Aggregate Size: A Pilot Experimental Investigation

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3685 ◽  
Author(s):  
Keke Lou ◽  
Peng Xiao ◽  
Aihong Kang ◽  
Zhengguang Wu ◽  
Pengcheng Lu
Keyword(s):  
Low Temperature ◽  
Crack Resistance ◽  
Fiber Length ◽  
Hot Mix Asphalt ◽  
Basalt Fiber ◽  
Aggregate Size ◽  
Temperature Deformation ◽  
Maximum Aggregate Size ◽  
Fiber Reinforced ◽  
Splitting Test

Fiber length is a key parameter for the mixture design of basalt fiber-reinforced hot mix asphalt (HMA), which significantly affects the mix performance. To evaluate the suitability of fiber lengths for HMA with different nominal maximum aggregate size (NMAS), basalt fiber with the lengths of 3, 6, 9, 12, and 15 mm were selected for dense graded gradations with different NMASs (namely, SUP-13, SUP-20, and SUP-25), so as to prepare the fiber-reinforced HMA mixtures. Then, the mix performance was evaluated by an indirect tensile asphalt cracking test (IDEAL-CT), a four-point bending beam fatigue test, a wheel tracking test, a uniaxial penetration test, a low temperature bending beam test, and a freeze-thaw splitting test. Based on the performance results, the optimum fiber length for each mix gradation was proposed by the normalization method. The results showed that adding basalt fiber can enhance the comprehensive performance of all three types of HMA to a great extent. Furthermore, fiber length presented remarkable impact on the crack resistance, the fatigue resistance of the HMA, and the low temperature crack resistance, but it had limited influence on the high temperature deformation resistance, and water stability. The optimum fiber length for SUP-13, SUP-20, and SUP-25 was 6, 9, and 12 mm, respectively.

Research on Crack Resistance Evaluation of Asphalt Mixture at Low Temperature

2013 ◽  
Vol 753-755 ◽  
pp. 668-672
Author(s):  
Li Jie Ma ◽  
Hai Bin Chen ◽  
Jin Yu Zhang
Keyword(s):  
Low Temperature ◽  
Crack Resistance ◽  
Tensile Strain ◽  
Unit Volume ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Bending Test ◽  
Test Unit ◽  
Research Areas ◽  
Temperature Crack

In order to improve the low temperature evaluation, on the basis of the low temperature bending test unit volume destruction to evaluate the low temperature crack resistance of asphalt mixtures. Since the destruction can be indicators of unit volume mixture critical flexural tensile strain and flexural strength of two indicators integrated. Therefore, use it to assess the low temperature crack resistance of asphalt mixture is more scientific, the indicators has also become a new method of low-temperature research areas.

THE EFFECT OF INCORPORATING RECLAIMED ASPHALT PAVEMENT ON THE PERFORMANCE OF HOT MIX ASPHALT MIXTURES

2015 ◽  
Vol 77 (32) ◽  
Author(s):  
Mohd Khairul Idham ◽  
Mohd Rosli Hainin
Keyword(s):  
Resilient Modulus ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Reclaimed Asphalt Pavement ◽  
Optimum Amount ◽  
Rutting Resistance ◽  
Reclaimed Asphalt

In pavement industries, incorporating appropriate amount of reclaimed asphalt pavement (RAP) in the fresh mixtures is one of the approaches to attain sustainable principle in construction. Usage RAP materials have been practiced since 1970s, however, pavements made with RAP will reach the end of service life and need to be recycled again. Only a few studies done on the second recycle of RAP (R2AP). Therefore, this paper aimed to investigate the effect of incorporating RAP and R2AP in the asphalt mixture. RAP was collected from in-service road which was exposed to the environment and traffic for seven years. While, the second cycle of RAP (R2AP) was obtained through the laboratory aging process.  20, 40, and 60 % of RAP and R2AP were mixed with fresh dense graded aggregates to form Asphaltic Concrete with 14 mm nominal maximum aggregate size (AC 14). Resilient modulus test was performed to evaluate the performance on rutting resistance. Tensile strength was also evaluated at 25 °C as an indicator for fatigue resistance. 60 % of RAP and 40 % of R2AP are observed to the best optimum amount to be added in the fresh mixture in order to improve both fatigue and rutting resistance.

Evaluation of Viscoelastic and Fracture Properties of Asphalt Mixtures with Long-Term Laboratory Conditioning

2018 ◽  
Vol 2672 (28) ◽  
pp. 503-513 ◽  
Author(s):  
Reyhaneh Rahbar-Rastegar ◽  
Jo Sias Daniel ◽  
Eshan V. Dave
Keyword(s):  
Viscoelastic Properties ◽  
Complex Modulus ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Cracking Behavior ◽  
Fracture Properties ◽  
Fracture Parameters

Aging affects the properties of asphalt mixtures in different ways; increase of stiffness, decrease of relaxation capability, and the increase of brittleness, resulting in changes in cracking behavior of asphalt mixtures. In this study, ten plant-produced, lab-compacted mixtures with various compositions (recycled materials, binder grades, binder source, and nominal maximum aggregate size) are evaluated at different long-term aging levels (24 hours at 135°C, 5 days at 95°C, and 12 days at 95°C on loose mix and 5 days at 85°C on compacted specimens). The asphalt mixture linear viscoelastic properties (|E*| and δ) and master curve shape parameters measured from complex modulus testing and fracture properties (measured from disc-shaped compact tension and semi-circular bending fracture testing) are compared at different levels of aging. The results indicate that the mixture exposure time to aging is proportional to the dynamic modulus and phase angle changes. Generally, the fracture parameters of mixtures become worse when aging level changes from 5 to 12 days aging. In spite of the similar viscoelastic properties, the mixtures with 24 hours at 135°C and 12 days at 95°C aging do not show similar fracture parameters.

scholarly journals Asphalt Mixture for the First Asphalt Concrete Directly Fastened Track in Korea

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Seong-Hyeok Lee ◽  
Dae-Wook Park ◽  
Hai Viet Vo ◽  
Samer Dessouky
Keyword(s):  
Asphalt Concrete ◽  
Design Method ◽  
Asphalt Mixture ◽  
Digital Camera ◽  
Aggregate Size ◽  
Fatigue Tests ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Aggregate Gradation ◽  
Modified Asphalt

The research has been initiated to develop the asphalt mixtures which are suitable for the surface of asphalt concrete directly fastened track (ADFT) system and evaluate the performance of the asphalt mixture. Three aggregate gradations which are upper (finer), medium, and below (coarser). The nominal maximum aggregate size of asphalt mixture was 10 mm. Asphalt mixture design was conducted at 3 percent air voids using Marshall mix design method. To make impermeable asphalt mixture surface, the laboratory permeability test was conducted for asphalt mixtures of three different aggregate gradations using asphalt mixture permeability tester. Moisture susceptibility test was conducted based on AASHTO T 283. The stripping percentage of asphalt mixtures was measured using a digital camera and analyzed based on image analysis techniques. Based on the limited research results, the finer aggregate gradation is the most suitable for asphalt mixture for ADFT system with the high TSR value and the low stripping percentage and permeable coefficient. Flow number and beam fatigue tests for finer aggregate asphalt mixture were conducted to characterize the performance of asphalt mixtures containing two modified asphalt binders: STE-10 which is styrene-butadiene-styrene (SBS) polymer and ARMA which is Crum rubber modified asphalt. The performance tests indicate that the STE-10 shows the higher rutting life and fatigue life.

scholarly journals Enhanced Dry Process Method for Modified Asphalt Containing Plastic Waste

2021 ◽  
Vol 8 ◽  
Author(s):  
Hasanain Radhi Radeef ◽  
Norhidayah Abdul Hassan ◽  
Ahmad Razin Zainal Abidin ◽  
Mohd Zul Hanif Mahmud ◽  
Nur Izzi Md. Yusoffa ◽  
...  
Keyword(s):  
Resilient Modulus ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Aggregate Size ◽  
Plastic Waste ◽  
Asphalt Mixtures ◽  
Maximum Aggregate Size ◽  
Dry Process ◽  
Modified Asphalt ◽  
And Performance

In recent years, the proliferation of plastic waste has become a global problem. A potential solution to this problem is the dry process, which incorporates plastic waste into asphalt mixtures. However, the dry process often has inconsistent performance due to poor interaction with binder and improper distribution of plastic waste particles in the mixture skeleton. This inconsistency may be caused by inaccurate mixing method, shredding size, mixing temperature and ingredient priorities. Thus, this study aims to improve the consistency of the dry process by comparing the control asphalt mixture and two plastic waste-modified asphalt mixtures prepared using the dry process. This study used crushed granite aggregate with the nominal maximum aggregate size of 14 mm whereas the shredded plastic bag is in the range of 5–10 mm. Quantitative sieving analysis and performance tests were carried out to examine the effects of plastic waste added into the asphalt mixture. The volumetric and performance properties combined with image analysis of the modified mixtures were obtained and compared with the control mixture. In addition, the moisture damage, resilient modulus, creep deformation and rutting were evaluated. This study also highlighted in detail the distribution of plastic particles in the final skeleton of the asphalt mixture. Based on the analysis, an enhanced dry process of mixing procedure was proposed and evaluated. Results showed that the addition of plastic particles using the conventional dry process leads to the deviation in the aggregate structure as high plastic content is added. Furthermore, the enhanced dry process developed in this study presents substantial enhancement in the asphalt performance, particularly with plastic waste that accounts for 20% of the weight of the asphalt binder.

Sign in / Sign up

Export Citation Format

Share Document