scholarly journals Preparation of Powders Containing Sb, Ni, and O for the Design of a Novel CO and C3H8 Sensor

2021 ◽  
Vol 11 (20) ◽  
pp. 9536
Author(s):  
Jorge Alberto Ramírez-Ortega ◽  
José Trinidad Guillén-Bonilla ◽  
Alex Guillén-Bonilla ◽  
Verónica María Rodríguez-Betancourtt ◽  
Lorenzo Gildo-Ortiz ◽  
...  

In this work, powders of NiSb2O6 were synthesized using a simple and economical microwave-assisted wet chemistry method, and calcined at 700, 800, and 900 °C. It was identified through X-ray diffraction that the oxide is a nanomaterial with a trirutile-type structure and space group P42/mnm (136). UV–Vis spectroscopy measurements showed that the bandgap values were at ~3.10, ~3.14, and ~3.23 eV at 700, 800, and 900 °C, respectively. Using scanning electron microscopy (SEM), irregularly shaped polyhedral microstructures with a size of ~154.78 nm were observed on the entire material’s surface. The particle size was estimated to average ~92.30 nm at the calcination temperature of 900 °C. Sensing tests in static atmospheres containing 300 ppm of CO at 300 °C showed a maximum sensitivity of ~72.67. On the other hand, in dynamic atmospheres at different CO flows and at an operating temperature of 200 °C, changes with time in electrical resistance were recorded, showing a high response, stability, and repeatability, and good sensor efficiency during several operation cycles. The response times were ~2.77 and ~2.10 min to 150 and 200 cm3/min of CO, respectively. Dynamic tests in propane (C3H8) atmospheres revealed that the material improved its response in alternating current signals at two different frequencies (0.1 and 1 kHz). It was also observed that at 360 °C, the ability to detect propane flows increased considerably. As in the case of CO, NiSb2O6’s response in propane atmospheres showed very good thermal stability, efficiency, a high capacity to detect C3H8, and short response and recovery times at both frequencies. Considering the great performance in propane flows, a sensor prototype was developed that modulates the electrical signals at 360 °C, verifying the excellent functionality of NiSb2O6.

2019 ◽  
pp. 1694-1703
Author(s):  
Reem Saadi Khaleel ◽  
Mustafa Shakir Hashim

Rapid breakdown anodization (RBA) process was used to fabricate TiO2 sensor to measure pressure and humidity and sense gases at room temperature. This chemical process transformed Ti to its oxide (TiO2) as a powder with amorphous phase as X ray diffraction (XRD) technique confirmed.  This oxide consisted from semi spherical nanoparticles and titania nanotubes (TNTs) as Scanning electron microscope (SEM) technique showed.  TiO2 powder was deposited on Ti substrates by using electrophoretic deposition (EPD) method.   Average pressure sensitivity was 0.34 MΩ/bar and hysteresis area was 1.4 MΩ .bar. Resistance of TiO2 decreased exponentially with the increasing of relative humidity (RH%). The sensitivity% of TiO2 for RH% was greater than 70% in the range of (50-95). TiO2 was tested as a sensor for Ammonia, Ethanol and Methanol. Its sensitivity and selectivity towards Ammonia were the greatest but the shortest response and recovery times were recorded toward Methanol.


2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Nadezhda Markova ◽  
Olga Berezina ◽  
Nikolay Avdeev ◽  
Alexander Pergament

Indium-zinc oxide (IZO) nanofiber matrices are synthesized on SiO2-covered silicon substrates by the electrospinning method. The nanofibers’ dimensions, morphology, and crystalline structure are characterized by scanning electron microscopy, atomic force microscopy, and X-ray diffraction. The results of studying the electrical properties of nanofibers, as well as their sensitivity to UV radiation depending on the In-to-Zn concentration ratio, are presented. It is shown that the highest sensitivity to UV is observed at the indium content of about 50 atomic %. The photocurrent increment with respect to the dark current is more than 4 orders of magnitude. The response and recovery times are 60 and 500 sec, respectively. The results obtained suggest that IZO nanofibers can find application as UV sensors with improved characteristics.


2013 ◽  
Vol 873 ◽  
pp. 304-310 ◽  
Author(s):  
Jin Zhang ◽  
Yu Min Zhang ◽  
Chang Yi Hu ◽  
Zhong Qi Zhu ◽  
Qing Ju Liu

The gas-sensing properties of zinc doped lanthanum ferrite (Zn-LaFeO3) compounds for formaldehyde were investigated in this paper. Zn-LaFeO3 powders were prepared using sol-gel method combined with microwave chemical synthesis. The powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The formaldehyde gas-sensing characteristics for the sample were examined. The experimental results indicate that the sensor based on the sample Zn-LaFeO3 shows excellent gas-sensing properties to formaldehyde gas. At the optimal operating temperature of 250°C, the sensitivity of the sensor based on LaFe0.7Zn0.3O3 to 100ppm formaldehyde is 38, while to other test gases, the sensitivity is all lower than 20. The response and recovery times for the sample to formaldehyde gas are 100s and 100s, respectively.


2018 ◽  
Vol 36 (3) ◽  
pp. 452-459
Author(s):  
Raad S. Sabry ◽  
Roonak Abdul Salam A. Alkareem

AbstractZnO-CuO flower-like hetero-nanostructures were successfully prepared by combining hydrothermal and dip coating methods. Flower-like hetero-nanostructures of ZnO-CuO were examined by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and UV-Vis. The sensing properties of ZnO-CuO flower-like hetero-nanostructures to volatile organic compounds (VOCs) were evaluated in a chamber containing acetone or isopropanol gas at room temperature. The sensitivity of ZnO-CuO flower-like hetero-nanostructures to VOCs was enhanced compared to that of pure leafage-like ZnO nanostructures. Response and recovery times were about 5 s and 6 s to 50 ppm acetone, and 10 s and 8 s to 50 ppm isopropanol, respectively. The sensing performance of ZnO-CuO flower-like hetero-nanostructures was attributed to the addition of CuO that led to formation of p-n junctions at the interface between the CuO and ZnO. In addition, the sensing mechanism was briefly discussed.


2020 ◽  
Vol 15 (1) ◽  
pp. 41-45 ◽  
Author(s):  
Zhi-Cheng Zhong ◽  
Zhao-Jun Jing ◽  
Kui-Yuan Liu ◽  
Tong Liu

We adopted the sol–gel and hydrothermal methods to prepare the TiO2 nanomaterials doped with ZnO. We adopted X-ray diffraction, scanning electron microscopy, and the Brunauer–Emmett–Teller method to investigate the materials’ structures and morphologies. The results showed that the prepared TiO2 nanomaterials had uniform size and good dispersibility. Gas sensors were fabricated and their performances in acetylene sensing were assessed. The results show that the sensor prepared with the ZnO/TiO2 nanomaterial doped with 10 wt% ZnO gave fast response and recovery times for acetylene gas at different concentrations. When the operating temperature was 280 °C, the gas sensor detected 200 ppm acetylene gas with a response sensitivity of 9.9, a response time of 5 s, and a recovery time of 2 s.


2000 ◽  
Vol 638 ◽  
Author(s):  
Elisabetta Comini ◽  
Matteo Ferroni ◽  
Vincenzo Guidi ◽  
Giuliano Martinelli ◽  
Michele Sacerdoti ◽  
...  

AbstractThe Mo-W-O thin films were deposited by RF reactive sputtering from composite target of W and Mo (20:80 weight ratio). Structural characterisation was carried out by X-ray diffraction spectroscopy and the composition of the film was obtained by Rutherford backscattering analysis. The layers were investigated by volt-amperometric technique for electrical and gas-sensing properties. The films were capable of sensing CO. No effect of poisoning of the surface was recorded and recovery of the resistance was complete. A concentration of CO as low as 15 ppm produced a relative variation in the conductance of 390% with response and recovery times of about 2 minutes at a working temperature of 200°C.


Sensors ◽  
2020 ◽  
Vol 20 (17) ◽  
pp. 4961
Author(s):  
Ziyang Yu ◽  
Liang Zhang ◽  
Xiangyue Wang ◽  
Dong He ◽  
Hui Suo ◽  
...  

ZnO and carbon quantum dots (CQDs) were synthesized by a hydrothermal method, and CQDs were doped into ZnO by a grinding method to fabricate a ZnO/CQDs composite. The X-ray diffraction and the scanning electron microscope revealed that the as-prepared ZnO has a structure of wurtzite hexagonal ZnO and a morphology of a flower-like microsphere which can provide more surface areas to adsorbed gases. The ZnO/CQDs composite has a higher gas sensitivity response to NO gas than ZnO microspheres. A gas sensitivity test of the ZnO/CQDs composite showed that the sensor had a high NO response (238 for 100 ppm NO) and NO selectivity. The detection limit of the ZnO/CQDs composite to NO was 100 ppb and the response and recovery times were 34 and 36 s, respectively. The active functional group provided by CQDs has a significant effect on NO gas sensitivity, and the gas sensitivity mechanism of the ZnO/CQDs composite is discussed.


2021 ◽  
pp. 2176-2187
Author(s):  
S.M. AbdulKareem ◽  
M.H. Suhail ◽  
I. K. Adehmash

     Chromium oxide (Cr2O3) doped ZnO nanoparticles were prepared by pulsed laser deposition (PLD) technique at different concentration ratios (0, 3, 5, 7 and 9 wt %) of ZnO on glass substrate. The effects of ZnO dopant on the average crystallite size of the synthesized nanoparticles was examined By X-ray diffraction. The morphological features were detected using atomic force microscopy (AFM). The optical band gap value was observed to range between 2.78 to 2.50 eV by UV-Vis absorption spectroscopy, with longer wavelength shifted in comparison with that of the bulk Cr2O3 (~3eV). Gas sensitivity, response, and recovery times of the sensor in the presence of NH3 gas were studied and discussed. In the present work, we found that the sensitivity was increased upon increasing the concentration ratio from 3 to 5%wt of ZnO, whereas it was decreased again over that value. Also, we found that the sensitivity was increased when increasing operating temperature, while the response time was decreased. The optimum concentrations ratio for NH3 gas sensitivity at 5%wt ZnO revealed sensitivity of 66.67% and response time of 14s at operating temperature of 300oC and 700mJ PLD energy.


2014 ◽  
Vol 1053 ◽  
pp. 177-180
Author(s):  
Dan Han ◽  
Peng Song ◽  
Qi Wang ◽  
Hui Hui Zhang

The La-doped porous In2O3 nanospheres were prepared by a simple hydrothermal method, and La3+ accounted for 3 mol% of the In3+. The La exists and has been doped in the lattice of In2O3 characterized respectively by the means of energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD), the morphology of the samples with uniform nanospheres observed by field-emission scanning electron microscopy (FESEM). Moreover, the sensor exhibits higher response properties compared with pure porous In2O3 nanospheres towards different acetone concentration at operating temperature 300 °C. The response and recovery times is about 13 s and 8 s to 50 ppm acetone.


Author(s):  
Artem Mikhailov ◽  
Vedran Vuković ◽  
Christian Kijatkin ◽  
Emmanuel Wenger ◽  
Mirco Imlau ◽  
...  

The complex trans-[RuNO(NH3)4F]SiF6 was synthesized in quantitative yield and the structure was characterized by X-ray diffraction and spectroscopic methods. The complex crystallizes in the non-centrosymmetric space group Pn. Hirshfeld surface analysis revealed that the dominant intermolecular interactions are of types H...F and F...O, which are likely to be responsible for the packing of the molecules in a non-centrosymmetric structure. Irradiation with blue light leads to the formation of Ru–ON (metastable state MS1) and Ru–η2-(NO) (metastable state MS2) bond isomers, as shown by IR and UV–Vis spectroscopy. The structural features of the MS1 isomer were elucidated by photocrystallography. The complex exhibits exceptionally good thermal stability of the metastable state MS1, such that it can be populated by light at 290–300 K, which is important for potential applications. The second harmonic (SH) emission can be generated by femtosecond-pulsed irradiation of the complex. The generated SH is rather efficient and stable under long-term exposure. Finally, since both metastable states and harmonic generation can be generated at room temperature, an attempt to drive the SH response by photoisomerization of the nitrosyl ligand was made and is discussed.


Sign in / Sign up

Export Citation Format

Share Document