Acetylene Sensing by ZnO/TiO2 Nanoparticles

2020 ◽  
Vol 15 (1) ◽  
pp. 41-45 ◽  
Author(s):  
Zhi-Cheng Zhong ◽  
Zhao-Jun Jing ◽  
Kui-Yuan Liu ◽  
Tong Liu
Keyword(s):  
Gas Sensors ◽  
Operating Temperature ◽  
Sol Gel ◽  
Fast Response ◽  
X Ray Diffraction ◽  
Uniform Size ◽  
X Ray ◽  
Recovery Times ◽  
Response And Recovery ◽  
Hydrothermal Methods

We adopted the sol–gel and hydrothermal methods to prepare the TiO2 nanomaterials doped with ZnO. We adopted X-ray diffraction, scanning electron microscopy, and the Brunauer–Emmett–Teller method to investigate the materials’ structures and morphologies. The results showed that the prepared TiO2 nanomaterials had uniform size and good dispersibility. Gas sensors were fabricated and their performances in acetylene sensing were assessed. The results show that the sensor prepared with the ZnO/TiO2 nanomaterial doped with 10 wt% ZnO gave fast response and recovery times for acetylene gas at different concentrations. When the operating temperature was 280 °C, the gas sensor detected 200 ppm acetylene gas with a response sensitivity of 9.9, a response time of 5 s, and a recovery time of 2 s.

Ce(1-x)MXO2, {M=Ru, In} Solid Solutions as Novel Gas Sensors for CO Detection

2011 ◽  
Vol 14 ◽  
pp. 135-143 ◽  
Author(s):  
R. Rangel ◽  
L. Chávez Chávez ◽  
M. Meléndrez ◽  
P. Batolo-Pérez ◽  
Eduardo G. Pérez-Tijerina ◽  
...  
Keyword(s):  
Surface Area ◽  
Solid Solutions ◽  
Gas Sensors ◽  
Electrical Resistance ◽  
Low Temperatures ◽  
Sol Gel ◽  
Fast Response ◽  
X Ray Diffraction ◽  
X Ray ◽  
Co Detection

In the present work, the study of semiconducting Ce(1-x)MXO2 (M=Ru, In) solid-solutions nanostructures with application to gas sensors is addressed. Nanostructured powers were prepared by means of the sol-gel route. The electrical resistance of obtained materials under different conditions of time, concentration and temperature in CO presence was tested. These systems were characterized using x-ray diffraction, SEM microscopy and surface area measurements. The solid solutions demonstrated good sensorial response at low temperatures, as well as fast response as a function of time. Our results show that these novel materials can be potentially applied as gas sensors.

scholarly journals Synthesis of CuO by Electrospinning Method for Sensing of Hydrogen and Carbon Monoxide Gases

2021 ◽  
Vol 68 (4) ◽  
pp. 945-954
Author(s):  
Abdollah Fallah Shojaei ◽  
Parisa Fallah Komsari
Keyword(s):  
Carbon Monoxide ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Particle Morphology ◽  
Fast Response ◽  
X Ray Diffraction ◽  
Sem Images ◽  
X Ray ◽  
Electrospinning Method ◽  
Response And Recovery

The pure CuO nanofibers were synthesized via the electrospinning method successfully. The calcinated CuO nanofibers were investigated for sensing hydrogen and carbon monoxide gases. Structural properties of the synthesized calcinated nanofibers were studied using Fourier –transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDX), and particle morphology by scanning electron microscopy (SEM). SEM images confirmed string-like structures, nanofibers. The sensor based on the calcinated CuO nanofibers exhibited excellent gas sensing performance at the low operating temperature of 175 °C and the fast response and recovery characteristics at a low concentration. Moreover, good stability, prominent reproducibility, and excellent selectivity are also observed based on the calcinated nanofibers. These results demonstrate the potential application of calcinated CuO nanofibers for sensing hydrogen (10–200 ppm) and carbon monoxide (400–700 ppm) gases.

Structural and Acetone Sensing Properties of La-Doped Porous In2O3 Nanospheres by Hydrothermal Synthesis

2014 ◽  
Vol 1053 ◽  
pp. 177-180
Author(s):  
Dan Han ◽  
Peng Song ◽  
Qi Wang ◽  
Hui Hui Zhang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Operating Temperature ◽  
X Ray Diffraction ◽  
Acetone Concentration ◽  
X Ray ◽  
Recovery Times ◽  
Response And Recovery ◽  
La Doped ◽  
Scanning Electron

The La-doped porous In2O3 nanospheres were prepared by a simple hydrothermal method, and La3+ accounted for 3 mol% of the In3+. The La exists and has been doped in the lattice of In2O3 characterized respectively by the means of energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD), the morphology of the samples with uniform nanospheres observed by field-emission scanning electron microscopy (FESEM). Moreover, the sensor exhibits higher response properties compared with pure porous In2O3 nanospheres towards different acetone concentration at operating temperature 300 °C. The response and recovery times is about 13 s and 8 s to 50 ppm acetone.

scholarly journals Preparation, Characterization, and Mechanistic Understanding of Pd-Decorated ZnO Nanowires for Ethanol Sensing

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Xiao Deng ◽  
Shengbo Sang ◽  
Pengwei Li ◽  
Gang Li ◽  
Fanqin Gao ◽  
...  
Keyword(s):  
Gas Sensing ◽  
Operating Temperature ◽  
Zno Nanowires ◽  
X Ray Diffraction ◽  
X Ray ◽  
Recovery Times ◽  
Response And Recovery ◽  
New Perspective ◽  
Ethanol Sensing ◽  
Higher Sensitivity

ZnO nanowires (ZnO-NWs) and Pd-decorated ZnO nanowires (Pd-ZnO-NWs) were prepared by hydrothermal growth and characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). When used for gas sensing, both types of nanowires showed a good selectivity to ethanol but a higher sensitivity and lower operating temperature were found with Pd-ZnO-NWs sensors comparing to those of ZnO-NWs sensor. When exposed to 200 ppm ethanol, our ZnO-NWs sensor showed a sensitivity of about 2.69 at 425°C whereas 1.3 at. % Pd-ZnO-NWs sensor provided a 57% more detection sensibility at 325°C. In addition, both response and recovery times of Pd-ZnO-NWs sensors were significantly reduced (9 s) comparing to the ZnO-NWs. Finally, Pd-ZnO-NWs sensor also showed a much lower detection limit of about 1 ppm. The sensing mechanism of Pd-ZnO-NWs sensors has also been clarified, thereby providing a new perspective for further improvement of the sensing performance of ethanol sensors.

CuOX Films for NO2 Detection: Microstructural Characterization

2013 ◽  
Vol 481 ◽  
pp. 133-136 ◽  
Author(s):  
T.N. Myasoedova ◽  
G.E. Yalovega ◽  
N.K. Plugotarenko ◽  
M. Brzhezinskaya ◽  
V.V. Petrov ◽  
...  
Keyword(s):  
Gas Sensors ◽  
Secondary Electron ◽  
Operating Temperature ◽  
Sol Gel ◽  
Microstructural Characterization ◽  
Temperature Treatment ◽  
Copper Oxides ◽  
Edge Structure ◽  
X Ray ◽  
X Ray Absorption

Copper oxides films as promising materials for gas sensors applications were studied. Copper oxide films were deposited onto Si/SiO2substrates using a citrate sol-gel method with the subsequent temperature treatment at 150-5000C. These films were characterized by means of secondary electron microscopy (SEM) and X-ray-absorption near-edge structure (XANES) spectroscopy. The prepared films were utilized in NO2sensors. The dependences of the NO2response on the operating temperature and NO2concentration (10-200 ppm) were investigated. The maximum NO2response was achieved for the film annealed at 2500C.

Xylene-sensing of Fe2(MoO4)3 nanoplates prepared via a hydrothermal method

2017 ◽  
Vol 10 (03) ◽  
pp. 1750022 ◽  
Author(s):  
Mengying Xu ◽  
Zhidong Lin ◽  
Wenying Guo ◽  
Yuyuan Hong ◽  
Ping Fu ◽  
...  
Keyword(s):  
Gas Sensors ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Hydrothermal Process ◽  
Optimum Operating ◽  
Average Crystalline Size ◽  
Optimum Operating Temperature ◽  
Recovery Times ◽  
Response And Recovery ◽  
Simple Hydrothermal Process

Fe2(MoO4)3 nanoplates were prepared via a simple hydrothermal process. The average crystalline size of these nanoplates is 85.8[Formula: see text]nm. The sensor based on Fe2(MoO4)3 shows a high gas sensing performance to xylene. The response of Fe2(MoO4)3 sensor is 25.9–100[Formula: see text]ppm xylene at optimum operating temperature of 340[Formula: see text]C. The response and recovery times to 100[Formula: see text]ppm xylene are 4 and 10[Formula: see text]s, respectively. Furthermore, the Fe2(MoO4)3 sensor exhibits remarkable selectivity detection of xylene gas with negligible responses to toluene and benzene. Therefore, the Fe2(MoO4)3 is a promising material for the detection of xylene gas sensors.

Fabrication of TiO2 sensor using rapid breakdown anodization method to measure pressure, humidity and sense gases at room temperature

2019 ◽  
pp. 1694-1703
Author(s):  
Reem Saadi Khaleel ◽  
Mustafa Shakir Hashim
Keyword(s):  
Room Temperature ◽  
Average Pressure ◽  
Spherical Nanoparticles ◽  
X Ray Diffraction ◽  
X Ray ◽  
Recovery Times ◽  
Sensitivity And Selectivity ◽  
Response And Recovery ◽  
Anodization Method ◽  
Rapid Breakdown Anodization

Rapid breakdown anodization (RBA) process was used to fabricate TiO2 sensor to measure pressure and humidity and sense gases at room temperature. This chemical process transformed Ti to its oxide (TiO2) as a powder with amorphous phase as X ray diffraction (XRD) technique confirmed.  This oxide consisted from semi spherical nanoparticles and titania nanotubes (TNTs) as Scanning electron microscope (SEM) technique showed.  TiO2 powder was deposited on Ti substrates by using electrophoretic deposition (EPD) method.   Average pressure sensitivity was 0.34 MΩ/bar and hysteresis area was 1.4 MΩ .bar. Resistance of TiO2 decreased exponentially with the increasing of relative humidity (RH%). The sensitivity% of TiO2 for RH% was greater than 70% in the range of (50-95). TiO2 was tested as a sensor for Ammonia, Ethanol and Methanol. Its sensitivity and selectivity towards Ammonia were the greatest but the shortest response and recovery times were recorded toward Methanol.

scholarly journals Oxide Nanomaterials Based on SnO2 for Semiconductor Hydrogen Sensors

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
George Fedorenko ◽  
Ludmila Oleksenko ◽  
Nelly Maksymovych
Keyword(s):  
Tin Dioxide ◽  
Sol Gel ◽  
Average Particle Size ◽  
Fast Response ◽  
Average Particle ◽  
Hydrogen Sensors ◽  
Measuring Range ◽  
X Ray ◽  
Response And Recovery ◽  
Good Repeatability

Nanosized tin dioxide with an average particle size of 5.3 nm was synthesized by a sol-gel method and characterized by IR spectroscopy, TEM, X-ray, and electron diffraction. The obtained SnO2 can be used as initial material for creation of gas-sensitive layers of adsorption semiconductor sensors. Addition of palladium into the initial nanomaterial allows to improve response to hydrogen of such sensors in comparison with sensors based on undoped SnO2 and provides fast response and recovery time, a wide measuring range of hydrogen content in air ambient, and good repeatability of the sensor signal. Such promising properties could make useful the sensors based on these nanomaterials for devices intended to determine hydrogen in air.

scholarly journals SnO2/TiO2 Thin Film n-n Heterostructures of Improved Sensitivity to NO2

Sensors ◽  
2020 ◽  
Vol 20 (23) ◽  
pp. 6830
Author(s):  
Piotr Nowak ◽  
Wojciech Maziarz ◽  
Artur Rydosz ◽  
Kazimierz Kowalski ◽  
Magdalena Ziąbka ◽  
...  
Keyword(s):  
Thin Film ◽  
Operating Temperature ◽  
Incidence Geometry ◽  
X Ray Diffraction ◽  
X Ray ◽  
Langmuir Blodgett ◽  
Response Recovery ◽  
Low Concentrations ◽  
Highly Sensitive ◽  
Recovery Times

Thin-film n-n nanoheterostructures of SnO2/TiO2, highly sensitive to NO2, were obtained in a two-step process: (i) magnetron sputtering, MS followed by (ii) Langmuir-Blodgett, L–B, technique. Thick (200 nm) SnO2 base layers were deposited by MS and subsequently overcoated with a thin and discontinuous TiO2 film by means of L–B. Rutile nanopowder spread over the ethanol/chloroform/water formed a suspension, which was used as a source in L–B method. The morphology, crystallographic and electronic properties of the prepared sensors were studied by scanning electron microscopy, SEM, X-ray diffraction, XRD in glancing incidence geometry, GID, X-ray photoemission spectroscopy, XPS, and uv-vis-nir spectrophotometry, respectively. It was found that amorphous SnO2 films responded to relatively low concentrations of NO2 of about 200 ppb. A change of more than two orders of magnitude in the electrical resistivity upon exposure to NO2 was further enhanced in SnO2/TiO2 n-n nanoheterostructures. The best sensor responses RNO2/R0 were obtained at the lowest operating temperatures of about 120 °C, which is typical for nanomaterials. Response (recovery) times to 400 ppb NO2 were determined as a function of the operating temperature and indicated a significant decrease from 62 (42) s at 123 °C to 12 (19) s at 385 °C A much smaller sensitivity to H2 was observed, which might be advantageous for selective detection of nitrogen oxides. The influence of humidity on the NO2 response was demonstrated to be significantly below 150 °C and systematically decreased upon increase in the operating temperature up to 400 °C.

A Formaldehyde Gas Sensor Based on Zinc Doped Lanthanum Ferrite

2013 ◽  
Vol 873 ◽  
pp. 304-310 ◽  
Author(s):  
Jin Zhang ◽  
Yu Min Zhang ◽  
Chang Yi Hu ◽  
Zhong Qi Zhu ◽  
Qing Ju Liu
Keyword(s):  
Gas Sensing ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Lanthanum Ferrite ◽  
Gas Sensing Properties ◽  
Recovery Times ◽  
Response And Recovery ◽  
Sensing Characteristics

The gas-sensing properties of zinc doped lanthanum ferrite (Zn-LaFeO3) compounds for formaldehyde were investigated in this paper. Zn-LaFeO3 powders were prepared using sol-gel method combined with microwave chemical synthesis. The powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The formaldehyde gas-sensing characteristics for the sample were examined. The experimental results indicate that the sensor based on the sample Zn-LaFeO3 shows excellent gas-sensing properties to formaldehyde gas. At the optimal operating temperature of 250°C, the sensitivity of the sensor based on LaFe0.7Zn0.3O3 to 100ppm formaldehyde is 38, while to other test gases, the sensitivity is all lower than 20. The response and recovery times for the sample to formaldehyde gas are 100s and 100s, respectively.

Sign in / Sign up

Export Citation Format

Share Document