scholarly journals Dynamic Responses of Asphalt Concrete Waterproofing Layer in Ballastless Track

2019 ◽  
Vol 9 (3) ◽  
pp. 375 ◽  
Author(s):  
Jie Zhou ◽  
Xianhua Chen ◽  
Qinghong Fu ◽  
Gang Xu ◽  
Degou Cai
Keyword(s):  
Cross Section ◽  
Asphalt Concrete ◽  
Test Section ◽  
High Speed ◽  
Viscoelastic Behavior ◽  
Dynamic Responses ◽  
Track Structure ◽  
High Speed Railway ◽  
Ballastless Track ◽  
Full Cross Section

The application of asphalt concrete waterproofing layer (ACWL) for the subgrade has been a trend in Chinese high-speed railway. The purpose of this research is to discuss the dynamic characteristics of full cross-section ACWL in the ballastless track structure under the train loads. The laboratory tests were conducted to evaluate the performance of the asphalt mixtures for the ACWL and a test section of ACWL was constructed on the high-speed railway in north China. The linear viscoelastic behavior of the asphalt concrete obtained from the test section was characterized by the generalized Maxwell model according to the results of dynamic modulus test. Then a 3D finite element model for the interaction system of vehicle and ballastless track structure was presented and validated by field measured data. The results indicated that the tensile strain at the bottom of the ACWL was at a relatively low level and the vertical dynamic responses of each structural layer are obviously reduced due to the application of ACWL. Therefore, the full cross-section ACWL helps to reduce the vibration of the track structure and maintain the long-term stability of the subgrade.

scholarly journals Mechanical Performance of a Ballastless Track System for the Railway Bridges of High-Speed Lines: Experimental and Numerical Study under Thermal Loading

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2876
Author(s):  
Yingying Zhang ◽  
Lingyu Zhou ◽  
Akim D. Mahunon ◽  
Guangchao Zhang ◽  
Xiusheng Peng ◽  
...  
Keyword(s):  
High Speed ◽  
Thermal Loading ◽  
Mechanical Performance ◽  
Track Structure ◽  
Box Girder ◽  
High Speed Railway ◽  
Ballastless Track ◽  
Track System ◽  
Girder Bridge ◽  
Track Slab

The mechanical performance of China Railway Track System type II (CRTS II) ballastless track suitable for High-Speed Railway (HSR) bridges is investigated in this project by testing a one-quarter-scaled three-span specimen under thermal loading. Stress analysis was performed both experimentally and numerically, via finite-element modeling in the latter case. The results showed that strains in the track slab, in the cement-emulsified asphalt (CA) mortar and in the track bed, increased nonlinearly with the temperature increase. In the longitudinal direction, the zero-displacement section between the track slab and the track bed was close to the 1/8L section of the beam, while the zero-displacement section between the track slab and the box girder bridge was close to the 3/8L section. The maximum values of the relative vertical displacement between the track bed and the bridge structure occurred in the section at three-quarters of the span. Numerical analysis showed that the lower the temperature, the larger the tensile stresses occurring in the different layers of the track structure, whereas the higher the temperature, the higher the relative displacement between the track system and the box girder bridge. Consequently, quantifying the stresses in the various components of the track structure resulting from sudden temperature drops and evaluating the relative displacements between the rails and the track bed resulting from high-temperature are helpful in the design of ballastless track structures for high-speed railway lines.

Analysis of Dynamic Responses of Bridge-Subgrade Transition of High-Speed Railway

2011 ◽  
Vol 90-93 ◽  
pp. 189-196 ◽  
Author(s):  
Chang Wei Yang ◽  
Jian Jing Zhang ◽  
Chuan Bin Zhu
Keyword(s):  
High Speed ◽  
Deflection Angle ◽  
Coupled System ◽  
Dynamic Responses ◽  
Practical Situation ◽  
High Speed Railway ◽  
Ballastless Track ◽  
Track Dynamics ◽  
Coupling Dynamics ◽  
Analysis Models

Referred the vehicle-track coupling dynamics theory [1] and the vertical dynamic analysis models of Bridge-Subgrade transition developed by Zhai [2] ，Wang [3] and others [4]. This article takes account of the interaction between different structural layers in the subgrade system further by using the dynamic ballastless track model and finally establishes a space dynamic numerical model of the vehicle-track-subgrade coupled system. The dynamic response of the coupled system is analyzed when the speed of the train is 350km/h and the transition is filled with graded broken stones mixed with cement of 3%. Results show that the setting forms of Bridge-Subgrade transition have little effect on the dynamic responses, so designers can choose it on account of the practical situation. Due to the location away from abutment about 5m has greater deformation; the stiffness within 5m should be designed alone. Based on the study from vehicle-track dynamics, we suggest that the maximum allowable track deflection angle is 0.9‰ and K30190Mpa within 5m behind the abutment.

Simplified seismic model of CRTS II ballastless track structure on high-speed railway bridges in China

2020 ◽  
Vol 211 ◽  
pp. 110453 ◽  
Author(s):  
Wei Guo ◽  
Yao Hu ◽  
Hongye Gou ◽  
Qiaodan Du ◽  
Wenbin Fang ◽  
...  
Keyword(s):  
High Speed ◽  
Track Structure ◽  
Seismic Model ◽  
High Speed Railway ◽  
Railway Bridges ◽  
Ballastless Track

Full-Scale Model Testing on Ballasted High-Speed Railway: Dynamic Responses and Accumulated Settlements

2018 ◽  
Vol 2672 (10) ◽  
pp. 125-135 ◽  
Author(s):  
Wei Li ◽  
Xuecheng Bian ◽  
Xiang Duan ◽  
Erol Tutumluer
Keyword(s):  
High Speed ◽  
Stable State ◽  
Model Testing ◽  
Full Scale ◽  
Dynamic Responses ◽  
Scale Model ◽  
Vibration Velocity ◽  
Track Structure ◽  
High Speed Railway ◽  
Soil Stress

High-speed trains generate much higher vibrations in track structures than conventional trains and intensive train passages (e.g., on the Beijing–Shanghai high-speed railway line where the train passage interval is less than 5 minutes) cause accumulated permanent settlement in the railway track substructures, which will decrease track performance and jeopardize the safety of trains. Since very few field measurements on ballasted high-speed railways are available in literature, this paper presents experimental results of vibration velocity, dynamic soil stress, and the accumulated settlement of a ballasted high-speed railway from a full-scale model testing facility with simulated trains moving loads at various speeds. A portion of a realistic ballasted railway consisting of track structure, ballast layer, subballast, embankment, and piled foundation was constructed in a larger box. An eight-actuator sequential loading system was used to generate equivalent vertical loadings on the track structure for simulating the dynamic excitations due to train movements. Dynamic stresses measured in the track substructure layers (ballast, subballast, and embankment) were found to be strongly dependent on train speeds especially for speeds higher than 144 km/h. It was found that both the vibration velocity and the dynamic soil stress were greatly amplified as the train speed increased to 300 km/h, and the ballast layer effectively reduced the vibrations transmitted from the track structure to underlying soil. The accumulated settlement of the substructure did not reach a stable state even after 100,000 moving train loads at a speed of 300 km/h.

Seismic Damage Mechanism of CRTS-II Slab Ballastless Track Structure on High-Speed Railway Bridges

2019 ◽  
Vol 20 (01) ◽  
pp. 2050011 ◽  
Author(s):  
Wei Guo ◽  
Yao Hu ◽  
Wenqi Hou ◽  
Xia Gao ◽  
Dan Bu ◽  
...  
Keyword(s):  
High Speed ◽  
Damage Mechanism ◽  
Seismic Damage ◽  
Track Structure ◽  
Seismic Responses ◽  
High Speed Railway ◽  
Transition Section ◽  
Finite Element Software ◽  
Ballastless Track ◽  
Track System

China Railway Track System II (CRTS II) slab ballastless track structure is one of commonly adopted track systems on the high-speed railway bridge, which has been found seismically vulnerable under strong earthquakes. To investigate the earthquake-induced damage mechanism of the CRTS II slab ballastless track structure, a nonlinear numerical model of typical 7-span simply supported bridge–track system was established by the finite element software OpenSees and well calibrated by the test data and relative literatures. The nonlinear time history analysis was employed to calculate seismic responses of bridge and track parts under a suite of 10 seismic records. Results demonstrate that the sliding layer in the track structure is the most damage-prone component, especially at the bridge-subgrade transition section, and the shear alveolar may also sustain earthquake-induced fail. By analyzing the seismic damage mechanism of the track structure, this paper reveals that the nonuniform displacement responses of the girders and friction plate at the bridge-subgrade transition section are main factors that result in the extensive damage of the sliding layer and failure of the shear alveolar. However, the damage of these two components are beneficial to reduce the seismic responses of other components in the track structure and protect them from being damaged. From the perspective of engineering safety, the sliding layer and shear alveolar should be rigorously designed because the residual displacement of the sliding layer increases along with the maximum displacement and the failure of the shear alveolar may make the whole track structure failed.

The Calculation of the Supporting Stress of Track Plate in Ballastless High-Speed Rail Structure

2011 ◽  
Vol 97-98 ◽  
pp. 3-9
Author(s):  
Yang Wang ◽  
Quan Mei Gong ◽  
Mei Fang Li
Keyword(s):  
Stress Distribution ◽  
High Speed ◽  
Design Theory ◽  
Moving Load ◽  
Structure Design ◽  
Track Structure ◽  
Beam Model ◽  
High Speed Rail ◽  
Slab Track ◽  
Ballastless Track

The slab track is a new sort of track structure, which has been widely used in high-speed rail and special line for passenger. However, the ballastless track structure design theory is still not perfect and can not meet the requirements of current high-speed rail and passenger line ballastless track. In this paper, composite beam method is used to calculate the deflection of the track plate and in this way the vertical supporting stress distribution of the track plate can be gotten which set a basis for the follow-up study of the dynamic stress distribution in the subgrade. Slab track plate’s bearing stress under moving load is analyzed through Matlab program. By calculation and analysis, it is found that the deflection of track plate and the rail in the double-point-supported finite beam model refers to the rate of spring coefficient of the fastener and the mortar.The supporting stress of the rail plate is inversely proportional to the supporting stress of the rail. The two boundary conditions of that model ,namely, setting the end of the model in the seams of the track plate or not , have little effect on the results. We can use the supporting stress of the track plates on state 1to get the distribution of the supporting stress in the track plate when bogies pass. Also, when the dynamic load magnification factor is 1.2, the track plate supporting stress of CRST I & CRST II-plate non-ballasted structure is around 40kPa.

scholarly journals Monitoring and Modeling Railway Structures on High-Speed Lines with Asphalt Concrete Underlay: A Study on the Bretagne–Pays de la Loire Line

2020 ◽  
Vol 2674 (12) ◽  
pp. 600-607
Author(s):  
Diana Khairallah ◽  
Olivier Chupin ◽  
Juliette Blanc ◽  
Pierre Hornych ◽  
Jean-Michel Piau ◽  
...  
Keyword(s):  
Asphalt Concrete ◽  
High Speed ◽  
Large Scale ◽  
Strain Gages ◽  
Railway Transportation ◽  
Dynamic Stresses ◽  
High Speed Railway ◽  
High Frequencies ◽  
High Acceleration ◽  
High Speed Trains

The design and durability of high-speed railway lines is a major challenge in the field of railway transportation. In France, 40 years of feedback on the field behavior of ballasted tracks led to improvements in the design rules. However, the settlement and wear of ballast, caused by dynamic stresses at high frequencies, remains a major problem on high-speed tracks leading to high maintenance costs. Studies have shown that this settlement is linked to the high acceleration produced in the ballast layer by high-speed trains traveling on the track, disrupting the granular assembly. The “Bretagne–Pays de la Loire” high-speed line (BPL HSL), with its varied subgrade conditions, represents the first large-scale application of asphalt concrete (GB) as the ballast sublayer. This line includes 77 km of conventional track with a granular sublayer of unbound granular material (UGM) and 105 km of track with an asphalt concrete sublayer under the ballast. During construction, instruments such as accelerometers, anchored deflection sensors, and strain gages, among others, were installed on four sections of the track. This paper examines the instrumentation as well as the acquisition system installed on the track. The data processing is explained first, followed by a presentation of the ViscoRail software, developed for modeling railway tracks. The bituminous section’s behavior and response is modeled using a multilayer dynamic response model, implemented in the ViscoRail software. A good match between experimental and calculated results is highlighted.

Sign in / Sign up

Export Citation Format

Share Document