scholarly journals Triangular Slot-Loaded Wideband Planar Rectangular Antenna Array for Millimeter-Wave 5G Applications

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 778
Author(s):  
Iftikhar Ahmad ◽  
Houjun Sun ◽  
Umair Rafique ◽  
Zhang Yi
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Communication Systems ◽  
Ground Plane ◽  
Simulated Data ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Single Antenna ◽  
Rectangular Patch ◽  
Half Power

This paper presents a design of a triangular slot-loaded planar rectangular antenna array for wideband millimeter-wave (mm-wave) 5G communication systems. The proposed array realizes an overall size of 35.5 × 14.85 mm2. To excite the array elements, a four-way broadband corporate feeding network was designed and analyzed. The proposed array offered a measured impedance bandwidth in two different frequency ranges, i.e., from 23 to 24.6 GHz and from 26 to 45 GHz. The single-antenna element of the array consists of a rectangular patch radiator with a triangular slot. The partial ground plane was used at the bottom side of the substrate to obtain a wide impedance bandwidth. The peak gain in the proposed array is ≈12 dBi with a radiation efficiency of >90%. Furthermore, the array gives a half-power beamwidth (HPBW) of as low as 12.5°. The proposed array has been fabricated and measured, and it has been observed that the measured results are in agreement with the simulated data.

scholarly journals A DR Loaded Substrate Integrated Waveguide Antenna for 60 GHz High Speed Wireless Communication Systems

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Nadeem Ashraf ◽  
Hamsakutty Vettikalladi ◽  
Majeed A. S. Alkanhal
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
High Speed ◽  
Metal Layer ◽  
Simulation Software ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Substrate Integrated Waveguide ◽  
60 Ghz ◽  
Single Antenna

The concept of substrate integrated waveguide (SIW) technology along with dielectric resonators (DR) is used to design antenna/array for 60 GHz communication systems. SIW is created in the substrate of RT/duroid 5880 having relative permittivityεr=2.23and loss tangenttan⁡δ=0.003. H-shaped longitudinal slot is engraved at the top metal layer of the substrate. Two pieces of the DR are placed on the slot without any air gap. The antenna structures are modeled using CST Microwave Studio and then the results are verified using another simulation software HFSS. Simulation results of the two designs are presented; first a single antenna element and then to enhance the gain of the system a broadside array of1×4is presented in the second design. For the single antenna element, the impedance bandwidth is 10.33% having a gain up to 5.5 dBi. Whereas in an array of1×4elements, the impedance bandwidth is found to be 10.70% with a gain up to 11.20 dBi. For the single antenna element and1×4antenna array, the simulated radiation efficiency is found to be 81% and 78%, respectively.

scholarly journals Decoupled and Descattered Monopole MIMO Antenna Array with Orthogonal Radiation Patterns

2020 ◽  
Author(s):  
Hussain Al-Rizzo ◽  
Ayman A. Isaac ◽  
Sulaiman Z. Tariq ◽  
Samer Yahya
Keyword(s):  
Antenna Array ◽  
Mutual Coupling ◽  
Ground Plane ◽  
Design Concept ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Radiation Patterns ◽  
Mimo Antenna ◽  
Single Antenna ◽  
Novel Design

This chapter introduces a novel design concept to reduce mutual coupling among closely-spaced antenna elements of a MIMO array. This design concept significantly reduces the complexity of traditional/existing design approaches such as metamaterials, defected ground plane structures, soft electromagnetic surfaces, parasitic elements, matching and decoupling networks using a simple, yet a novel design alternative. The approach is based on a planar single decoupling element, consisting of a rectangular metallic ring resonator printed on one face of an ungrounded substrate. The decoupling structure surrounds a two-element vertical monopole antenna array fed by a coplanar waveguide structure. The design is shown both by simulations and measurements to reduce the mutual coupling by at least 20 dB, maintain the impedance bandwidth over which S11, is less than −10 dB, and reduce the envelope correlation coefficient to below 0.001. The boresight of the far-field radiation patterns of the two vertical monopole wire antennas operating at 2.4 GHz and separated by 8 mm (λo/16), where λo is the free-space wavelength at 2.45 GHz, is shown to be orthogonal and inclined by 45° with respect to the horizontal (azimuthal) plane while maintaining the shape of the isolated single antenna element.

scholarly journals A Novel High Gain Monopole Antenna Array for 60 GHz Millimeter-Wave Communications

2020 ◽  
Vol 10 (13) ◽  
pp. 4546
Author(s):  
Tarek S. Mneesy ◽  
Radwa K. Hamad ◽  
Amira I. Zaki ◽  
Wael A. E. Ali
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Ground Plane ◽  
High Gain ◽  
Monopole Antenna ◽  
Impedance Bandwidth ◽  
Single Element ◽  
60 Ghz ◽  
Defected Ground Structure ◽  
Element Array

This paper presented the design and implementation of a 60 GHz single element monopole antenna as well as a two-element array made of two 60 GHz monopole antennas. The proposed antenna array was used for 5G applications with radiation characteristics that conformed to the requirements of wireless communication systems. The proposed single element was designed and optimized to work at 60 GHz with a bandwidth of 6.6 GHz (57.2–63.8 GHz) and a maximum gain of 11.6 dB. The design was optimized by double T-shaped structures that were added in the rectangular slots, as well as two external stubs in order to achieve a highly directed radiation pattern. Moreover, ring and circular slots were made in the partial ground plane at an optimized distance as a defected ground structure (DGS) to improve the impedance bandwidth in the desired band. The two-element array was fed by a feed network, thus improving both the impedance bandwidth and gain. The single element and array were fabricated, and the measured and simulated results mimicked each other in both return loss and antenna gain.

scholarly journals Miniature Dual-Band Substrate Integrated Waveguide Slotted Antenna Array for Millimeter-Wave 5G Applications

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Fei-Peng Lai ◽  
Lu-Wu Chang ◽  
Yen-Sheng Chen
Keyword(s):  
Antenna Array ◽  
Millimeter Wave ◽  
Communication Systems ◽  
Single Layer ◽  
High Gain ◽  
Dual Band ◽  
Substrate Integrated Waveguide ◽  
Suitable Candidate ◽  
Fifth Generation ◽  
Half Power

A compact substrate integrated waveguide (SIW) antenna array that operates at 28 GHz and 38 GHz is proposed for fifth generation (5G) applications. The proposed array consists of four SIW cavities fabricated on one single layer of substrate. Each cavity implements a rhombic slot and a triangular-split-ring slot, resonating on TE101 and TE102 modes at 28 GHz and 38 GHz, respectively. In comparison with dual-band SIW antennas in the literature, the proposed configuration depicts a miniature footprint (28.7 × 30.8 mm2) without stacking substrates. To excite the four cavities with equal power, a broadband power divider that supports the propagation of TE10 mode is designed. Accordingly, the impedance bandwidths are 26.6–28.3 GHz and 36.8–38.9 GHz. The measured realized peak gain over the lower and higher bands is 9.3–10.9 dBi and 8.7–12.1 dBi, respectively. The measured half-power beam widths (HPBWs) at 28 GHz and 38 GHz are 20.7° and 15.0°, respectively. Considering these characteristics, including dual bands, high gain, narrow beam widths, miniaturization, and single layer, the proposed antenna array is a suitable candidate for millimeter-wave 5G communication systems with the flexibility in switching operating frequency bands against channel quality variations.

SERIES FEED FAN-BEAM ANTENNA ARRAY WITH A LOW SIDELOBE LEVEL FOR POSITIONING SYSTEM

2020 ◽  
pp. 55-65
Author(s):  
Le Minh Thuy
Keyword(s):  
Antenna Array ◽  
Radiation Pattern ◽  
Amplitude Distribution ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Positioning System ◽  
Sidelobe Level ◽  
Single Antenna ◽  
Low Sidelobe

In this paper, a novel antenna array at 5GHz is presented with a low sidelobe level and wide impedance bandwidth for indoor positioning applications . The antenna array has the size of 450 ×57×0.8 mm3 with the high gain of 14.5dBi and the low SLL of -18 dB at 5GHz. The series feed using Unequal Split T-Junction is proposed with the Chebyshev-amplitude distribution to improve SLL. Besides the 1800 phase and amplitude distribution, by deploying driven elements above each single antenna element, the radiation pattern and the gain of the antenna aray are significantly improved.

Dual-band B-shaped antenna array for satellite applications

2020 ◽  
pp. 1-8
Author(s):  
Muhammad Mateen Hassan ◽  
Muzhair Hussain ◽  
Adnan Ahmed Khan ◽  
Imran Rashid ◽  
Farooq Ahmed Bhatti
Keyword(s):  
Antenna Array ◽  
Impedance Matching ◽  
Ground Plane ◽  
Bottom Layer ◽  
Dual Band ◽  
Impedance Bandwidth ◽  
Rectangular Patch ◽  
Full Wave ◽  
Satellite Applications ◽  
Strip Lines

Abstract The paper presents a 1 × 2 B-shaped antenna array for dual-band operation at 4 and 8 GHz. The antenna design consists of a rectangular patch with two annular-strip lines fabricated on the top layer and finite ground plane on the bottom layer. The array is formed by designing an optimum T-shaped microstrip line for impedance matching. The dimensions of the antenna array are 78 × 36 × 1.6 mm3. Full-wave simulations have been conducted and the measured results are in good consent with the simulated results. The measured impedance bandwidth (reference −10 dB) has been observed at 3.84–4.16 and 7.78–8.38 GHz. Measured peak gain and radiation efficiency at 4 and 8 GHz are 8.3, 9.4 dB and 82.5 and 81.2%, respectively.

Light-weight wideband antenna array with low sidelobes for SAR applications

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Reza Kazemi ◽  
Mohsen Fallah ◽  
Bijan Abbasi ◽  
Seyyed Hossein MohseniArmaki
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Linear Array ◽  
Side Lobe ◽  
Impedance Bandwidth ◽  
Side Lobe Level ◽  
Antenna Element ◽  
Light Weight ◽  
Content Type ◽  
Compact Size

Purpose The purpose of this study is to achieve the low-cost, light-weight and compact antenna array with wide bandwidth and low side lobe levels for synthetic aperture radar (SAR) applications in Ku frequency band. Design/methodology/approach A compact design of a rectangular microstrip patch antenna array using multilayered dielectric structure is presented in Ku-band for advanced broadband SAR systems. In this design, stepped pins are used to connect the microstrip feed lines to the radiating patches. Findings The simulation and fabrication results of the multilayered antenna and a 1×16-element linear array of the antenna with Taylor amplitude distribution in the feeding network are presented. The antenna element has a 10-dB impedance bandwidth of more than 26%, and the linear array shows reduction in bandwidth percentage (about 15.4%). Thanks to Taylor amplitude tapering, the side lobe level (SLL) of the array is lower than −24 dB. The maximum measured gains of the antenna element and the linear array are 7 and 19.2 dBi at the center frequency, respectively. Originality/value In the communication systems, a high gain narrow beamwidth radiation pattern achieved by an array of multiple antenna elements with optimized spacing is a solution to overcome the path loss, atmospheric loss, polarization loss, etc. Also, wideband characteristics and compact size are desirable in satellite and SAR systems. This paper provides the combination of these features by microstrip structures.

scholarly journals Minimized Triple-Band Eight-Element Antenna Array for 5G Metal-frame Smartphone Applications

Micromachines ◽  
2022 ◽  
Vol 13 (1) ◽  
pp. 136
Author(s):  
Jianlin Huang ◽  
Zhuoni Chen ◽  
Qibo Cai ◽  
Tian Hong Loh ◽  
Gui Liu
Keyword(s):  
Antenna Array ◽  
Multiple Input Multiple Output ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Total Efficiency ◽  
Smartphone Applications ◽  
Single Antenna ◽  
Metal Frame ◽  
5 Ghz ◽  
Triple Band

A multiple-input-multiple-output (MIMO) antenna array for triple-band 5G metal-frame smartphone applications is proposed in this paper. Each single antenna element consists of an S-shaped feeding strip and an L-shaped radiation strip on the metal frame. The dimension of the antenna element is only 6.5 mm × 7 mm (0.076 λ0 × 0.082 λ0, λ0 is the free-space wavelength at the frequency of 3.5 GHz). The −6 dB impedance bandwidth of the proposed eight-antenna array can cover 3.3–3.8 GHz, 4.8–5 GHz, and 5.15–5.925 GHz. The evolution design and the analysis of the optimal parameters for a single antenna element are derived to investigate the principle of the antenna. The measured total efficiency is larger than 70%. The measured isolation is better than 13 dB. The measurements of the prototype agree well with the simulation results.

scholarly journals A Broadband High-Gain Printed Antenna Array Using Dipole and Loop Patches for 5G Communication Systems

2021 ◽  
Vol 15 ◽  
pp. 42-45
Author(s):  
Yuanzhi Liu ◽  
Mustapha C.E. Yagoub
Keyword(s):  
Antenna Array ◽  
Communication Systems ◽  
Low Cost ◽  
High Gain ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Wave Band ◽  
Printed Antenna ◽  
Compact Size ◽  
5G Communication

A broadband and high-gain printed antenna array is presented in this paper. Its single antenna element consists of a loop and two symmetric dipole patches, making the element exhibiting broad impedance bandwidth and improved gain at the targeted frequency, which is 28 GHz, one of the 5G mm-wave band, for this design. An 8×3 antenna array fed by a microstrip line feed network was designed and simulated. With a compact size of 98×32.5 mm2 , the array presents a broad -10 dB impedance bandwidth of 6.8 GHz (24.3%) and a high gain of 18 dBi at 28 GHz. Besides, the single-layered array also features low profile, simple geometry, and low cost, making it a good candidate for 5G communication systems.

Quad-Band multi-polarized antenna with modified electric-inductive−capacitive resonator

2021 ◽  
pp. 1-12
Author(s):  
Ghanshyam Singh ◽  
Binod Kumar Kanaujia ◽  
Vijay Kumar Pandey ◽  
Sachin Kumar
Keyword(s):  
Communication Systems ◽  
Ground Plane ◽  
Axial Ratio ◽  
Antenna Design ◽  
Planar Antenna ◽  
Rectangular Slot ◽  
Printed Circuits ◽  
Rectangular Patch ◽  
Easy Integration ◽  
Defected Ground Plane

Abstract A compact circularly polarized (CP) patch antenna is presented for modern communication systems. The prospective antenna consists of a microstrip-line inset-fed rectangular patch and a defected ground plane. A rotated rectangular slot and a modified electric-inductive-capacitive (m-ELC) resonator are introduced in the patch and the ground plane to achieve multiband behaviour. A corner of the radiating patch is truncated and an arrow-shaped stub is introduced for generating circular polarization. The physical area of the substrate is 0.26λ0 × 0.22λ0, and the radiator size is 0.16λ0 × 0.14λ0, where λ0 is the free-space wavelength estimated at the lowest frequency. The measured (S11≤-10 dB) bandwidths of the antenna are 80 MHz (3.58%) at 2.23 GHz, 75 MHz (2.64%) at 2.84 GHz, 80 MHz (2.50%) at 3.19 GHz, and 70 MHz (1.82%) at 3.83 GHz. The measured 3-dB axial ratio bandwidths are 40 MHz (1.41%), 100 MHz (3.12%), and 60 MHz (1.57%) at 2.84, 3.20 and 3.82 GHz, respectively. The proposed planar antenna design does not need dual-feed or multi-layered patches for achieving multiple CP bands. It offers easy integration with the printed circuits of the communication systems.

Sign in / Sign up

Export Citation Format

Share Document